Ricoh Aficio MP7500SP User Manual

							3
Accessing User Tools (System Settings)
This section is for Administrators in charge of this machine.
User Tools allow you to change or set defaults.
Note
❒Operations for system settings differ from normal operations. Always quit
User Tools when you have finished.
❒Any changes you make with User Tools remain in effect even if the main
power switch or operation switch is turned off, or the {Energy Saver} or {Clear
Modes} key is pressed.
Reference
p.4 “Quitting User Tools”
Changing Default Settings
This section describes how to change the settings of User Tools.
Important
❒If the Administrator Authentications specified, contact your administrator.
APress the {User Tools/Counter} key.
BSelect the menu.
To change the System Settings, Press [System Settings].
To change the Copier/Document Server Features, Press [Copier / Document
Server Features].
To change the Printer Features, Press [Printer Features].
To change the Scanner Features, Press [Scanner Features].
To change the displayed language, press [Français] or [English].
To find out who to contact for maintenance and where to order consumables,
press [Enquiry].
To check the counter, press [Counter].
CSelect the menu tab.
AMN001S
Downloaded From ManualsPrinter.com Manuals 
						

							4
DChange settings by following instructions on the display, and then press
[OK].
Note
❒To cancel changes made to settings and return to the initial display, press
the {User Tools/Counter} key.
Reference
p.41 “System Settings”
p.95 “Copier/Document Server Features”
p.137 “Printer Features”
p.153 “Scanner Features”
p.217 “Other User Tools”
Quitting User Tools
This section describes how to end User Tools.
APress the {User Tools/Counter} key.
Note
❒You can also quit User Tools by pressing [Exit].
About Menu Protect
Using Menu Protect, you can limit the settings available to users other than the
administrator. In the following User Tools menus, you can specify Menu Protect
for each setting.
 Copier/Document Server Features
Printer Features
 Scanner Features
For details about menu protect, contact your administrator.
AMN001S
Downloaded From ManualsPrinter.com Manuals 
						

							5
1. Connecting the Machine
Connect the machine to the network to configure network environment.
Connecting to the Interfaces
This section explains how to check the machine’s interface, connect the machine
according to the network environment, and specify the network settings.
1.IEEE 1394 ports (optional)
Ports for connecting the IEEE 1394 inter-
face cable
2.10BASE-T/100BASE-TX port
Port for connecting the 100BASE-TX or
10BASE-T cable
Port for connecting the 1000BASE-T,
100BASE-TX or 10BASE-T cable when
the Gigabit Ethernet (Optional) is in-
stalled
3.USB2.0 port
Port for connecting the USB2.0 interface
cable
4.IEEE 1284 port (optional)
Port for connecting the IEEE 1284 inter-
face cable
5.Wireless LAN port (optional)
Port for using the wireless LAN
Note
❒You cannnot install two or more of the
options below: IEEE 1394 interface
board, IEEE 1284 interface board,
IEEE 802.11b wireless LAN 
AMC004S
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting the Machine
6
1
Connecting to the Ethernet Interface
Connect 10BASE-T or 100BASE-TX cable to the Ethernet interface.
Important
❒If the main power switch is turned On, turn it Off.
AA ferrite core for the Ethernet cable is supplied with this machine. The
Ethernet cable loop should be about 15 cm (5.9 inch) (1) from the machine
end of the cable.
BMake sure the main power switch on the machine is Off.
CConnect the Ethernet interface cable to the 10BASE-T/100BASE-TX port.
DConnect the other end of the Ethernet cable to a network connection device
such as a hub.
AEV047S
AMM007S
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting to the Interfaces
7
1
ETurn the main power switch of the machine on.
AIndicator (green)
Remains green when the machine is properly connected to the network.
BIndicator (yellow)
Turns yellow when 100 BASE-TX is operating. Turns off when 10 BASE-T
is operating.
Reference
Turning On the Power About This Machine
Preparing the Machine Printer Reference
AMM008S
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting the Machine
8
1
Connecting to the USB Interface
Connect the USB2.0 interface cable to the USB2.0 port.
AConnect the USB 2.0 interface cable to the USB2.0 port.
BConnect the other end to the USB port on the host computer.
Note
❒Purchase a USB cable separately according to a personal computer in use.
❒The USB 2.0 interface board is supported by Windows Me / 2000 / XP,
Windows Server 2003, Mac OS X v10.3.3 or higher.
 For Windows Me:
Make sure to install USB Printing Support. If USB 2.0 is used with
Windows Me, only a speed equal to that of USB 1.1 is possible.
For Mac OS:
To use Macintosh, the machine must be equipped with the optional
PostScript 3 unit. If USB 2.0 is used with Mac OS X v10.3.3 or higher, a
transfer speed of USB 2.0 is supported.
❒For details about installing the printer driver, see Preparing the Machine
Printer Reference.
Reference
Preparing the Machine Printer Reference
AMM009S
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting to the Interfaces
9
1
Connecting to the IEEE 1394 Interface
Connect the IEEE 1394 interface cable to the IEEE 1394 interface board.
AConnect the IEEE 1394 interface cable to the IEEE 1394 port.
BFor IEEE 1394 (SCSI print) connection, plug the other end of the cable into
the interface connector on the host computer.
Make sure about the shape of the connector to the computer. Fasten the con-
nector securely to the computer.
Note
❒Use the interface cable supplied with the IEEE 1394 interface board (op-
tional).
❒Make sure the interface cable is not looped.
❒Two interface ports are available for connecting the IEEE 1394 interface ca-
ble. Either is suitable.
❒For details about installing the printer driver, see Preparing the Machine
Printer Reference.
Reference
Turning On the Power About this machine
Preparing the Machine Printer Reference
Connecting to the IEEE 1284 Interface
Connect the IEEE 1284 interface cable to the IEEE 1284 interface board.
AMake sure the main power switch on the machine is Off.
If the main power switch is turned On, turn it Off.
BTurn off the main power switch of the host computer
AMM010S
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting the Machine
10
1
CConnect the IEEE 1284 interface cable to the IEEE 1284 port.
To make the connection, use the conversion connector (1) supplied with the
IEEE 1284 interface board.
DPlug the other end of the cable into the interface connector on the host com-
puter.
Make sure about the shape of the connector to the computer. Fasten the con-
nector securely to the computer.
ETurn the main power switch of the machine On.
FTurn on the host computer.
When using Windows 95/98/Me/2000/XP and Windows Server 2003, a
printer driver installation screen might appear when the computer is turned
on. If this happens, click [Cancel] on the screen.
Note
❒For details about installing the printer driver, see Preparing the Machine
Printer Reference
Reference
Turning On the Power About this machine
Preparing the Machine Printer Reference
Connecting to the IEEE 802.11b (Wireless LAN) Interface
Connecting to the IEEE 802.11b (wireless LAN) interface.
Note
❒Check the setting of IPv4 address and subnet mask of this machine.
❒For how to set IPv4 address and subnet mask from the control panel of the
machine, see Interface Settings.
Reference
p.55 “Network”
AMB011S
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting to the Interfaces
11
1
Setup Procedure
Setup IEEE 802.11b (wireless LAN) according to the following flow:
Note
❒Select [802.11 Ad-hoc Mode] when connecting Windows XP as a wireless LAN
client using Windows XP standard driver or utilities, or when not using the
infrastructure mode.
❒For details about how to make settings of wireless LAN from the control pan-
el on the machine, see IEEE 802.11b.
❒For details about how to make settings of wireless LAN from other than the
control panel on the machine, see Using Utilities to Make Settings.
❒For details about the setting items, see IEEE 802.11b.
Reference
p.62 “IEEE 802.11b”
p.33 “Using Utilities to Make Settings”
AME006S
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting the Machine
12
1
Checking the Connection
Check the wireless LAN connection.
Make sure the LED of the IEEE 802.11b interface unit is lit.
❖When using in infrastructure mode
1.If [LAN Type] on the [Interface Settings] / [Network] screen is not set to [IEEE
802.11b], it does not light, even if the main power is on.
2.If it is connected properly to the network, the LED is green when in infra-
structure mode. If the LED is blinking, the machine is searching for devices.
❖When using in adhoc mode / 802.11 adhoc mode
1.If the IEEE 802.11b interface unit is working, it is lit in orange.
2.If it is connected properly to the network, the LED is green when in adhoc
mode or 802.11 adhoc mode. If the LED is blinking, the machine is searching
for devices. The LED will light after a few seconds.
Print the configuration page to verify settings.
Note
❒For more information about printing a configuration page, see Print List.
Reference
p.138 “Printing the configuration page”
ZGDH600J
1
2
ZGDH600J
1
2
Downloaded From ManualsPrinter.com Manuals