Ricoh Aficio MP7500SP User Manual

Timer Settings
53
2
❖Copier / Document Server Auto Reset Timer (copier/Document Server)
Specifies the time to elapse before copier and Document Server modes reset.
On
Off
If [Off] is selected, the machine does not automatically switch to the user code
entry screen.
The time can be set from 10 to 999 seconds, using the number keys.
The timing is set to 60 second(s) by default.
❖Printer Auto Reset Timer (printer)
Specifies the time to elapse before the printer function resets.
On
Off
The time can be...

System Settings
54
2
❖Weekly Timer Code
Set a password (using not more than eight digits) for turning on the power
during the time periods when Weekly Timer turns off the machines power.
On
Off
If you have selected On, enter the password. When you select on, you can-
not use the machine even if you turn the power switch to On, unless you en-
ter the password. If you select Off, you do not have to enter a password to
switch on the machine, you need only turn the power switch to On.
❖Weekly Timer: Monday...

Interface Settings
55
2 Interface Settings
This section describes various items of [Interface Settings] under [System Settings].
Default settings are shown in bold type.
Reference
p.3 “Accessing User Tools (System Settings)”
Network
This section describes various items of [Network] under [Interface Settings].
❖Machine IPv4 Address
Before using this machine in the network environment, you must configure
the IP address and subnet mask.
When you select [Specify], enter the [Machine IPv4 Address] and...

System Settings
56
2
❖IPv6 Gateway Address
The machine’s IPv6 gateway address appears.
❖IPv6 Stateless Address Autoconfiguration
You can set “IPv6 Stateless Address Autoconfiguration” to “Active” or “Inac-
tive”.
Active
Inactive
❖DNS Configuration
Make settings for the DNS server.
When you select [Specify], enter the [DNS Server 1] - [DNS Server 3] IP address
as “xxx.xxx.xxx.xxx(“x indicates a number).
Auto-Obtain (DHCP)
Specify
 DNS Server 1: 000.000.000.000
 DNS Server 2: 000.000.000.000
 DNS...

Interface Settings
57
2
❖Effective Protocol
Select the protocol to use in the network.
IPv4: Active / Inactive
 IPv6: Active / Inactive
NetWare: Active / Inactive
 SMB: Active / Inactive
 AppleTalk: Active / Inactive
❖NCP Delivery Protocol
Select the protocol for NCP delivery.
IPX Priority
TCP / IP Priority
IPX Only
 TCP / IP Only
❖NW Frame Type
Select the frame type when you use NetWare.
Auto Select
Ethernet II
 Ethernet 802.2
 Ethernet 802.3
 Ethernet SNAP
❖SMB Computer Name
Specify the...

System Settings
58
2
❖Ethernet Speed
Set the access speed for networks.
Select a speed that matches your network environment. [Auto Select] should
usually be selected.
Auto Select
 10Mbps Full Duplex
 10Mbps Half Duplex
 100Mbps Full Duplex
 100Mbps Half Duplex
❖LAN Type
When you have installed the optional IEEE 802.11b interface unit, select inter-
face, IEEE 802.11b (wireless LAN) or Ethernet.
Ethernet
 IEEE 802.11b
Appears when the IEEE 802.11b interface unit is installed.
If Ethernet and IEEE...

Interface Settings
59
2
❖Machine Name
Specify the machine name.
Enter the machine name using up to 31 alphanumerical characters.
Parallel Interface
This section describes various items of [Parallel Interface] under [Interface Settings].
[Parallel Interface] is displayed when this machine is installed with the IEEE 1284
interface board (optional).
❖Parallel Timing
Sets the timing for the control signal of the parallel interface.
ACK Outside
ACK Inside
STB Down
❖Parallel Communication Speed
Sets the...

System Settings
60
2
IEEE 1394
This section describes various items of [IEEE 1394] under [Interface Settings].
[IEEE 1394] is displayed when this machine is installed with the IEEE 1394 inter-
face board.
❖IPv4 Address
When you connect the machine to a network using the IEEE 1394 interface,
you must configure the IP address and subnet mask.
When you select [Specify], enter the [Machine IPv4 Address] and [Sub-net Mask]
as “xxx.xxx.xxx.xxx”(“x” indicates a number).
When you use the IEEE 1394 interface on a...

Interface Settings
61
2
❖WINS Configuration
You can specify the WINS server settings.
If [On] is selected, specify the WINS Server IPv4 address as “xxx.xxx.xxx.xxx
(“xxx indicates a number).
If DHCP is in use, specify the [Scope ID].
Enter [Scope ID] using up to 31 alphanumeric characters.
On
 Primary WINS Server: 000.000.000.000
 Secondary WINS Server: 000.000.000.000
Scope ID
Off
❖IPv4 over 1394
When you use the IPv4 over 1394 function of the IEEE 1394 interface to con-
nect the machine to the...

System Settings
62
2
IEEE 802.11b
This section describes various items of [IEEE 802.11b] under [Interface Settings].
[IEEE 802.11b] is displayed when this machine is installed with the wireless LAN
interface board (optional).
Implement respective settings simultaneously.
❖Communication Mode
Be sure to make all settings simultaneously.
 802.11 adhoc
adhoc
Infrastructure Mode
❖SSID Setting
Specifies SSID to distinguish the access point in infrastructure mode or 802.11
adhoc mode.
The characters that can...