Ricoh Aficio MP 6000SP User Manual

							Reproduction Ratio
91
3
Inch version
 25%
 11”×17” → 5
1/2”×81/2” (50%)
 11”×17” → 8
1/2”×11” (65%)
 11”×15” → 8
1/2”×11” (73%)
8
1/2”×14” → 81/2”×11” (78%)
8
1/2”×13” → 81/2”×11” (85%)
 93%
8
1/2”×14” → 11”×17” (121%)
8
1/2”×11” → 11”×17” (129%)
5
1/2”×81/2” → 81/2”×14” (155%)
5
1/2×81/2 → 11×17 (200%)
 400%
 User R / E Ratio (25-400%)
❖R / E Ratio Priority
You can set the ratio with priority when [Reduce/ Enlarge] is pressed.
The default setting is 71% (Metric version) / 73% (Inch version).
❖Ratio for Create Margin
You can set a Reduce/Enlarge ratio when registering Create Margin in a
shortcut key.
Enter a ratio using number keys (in the range of 90 to 99%).
The default setting is 93%.
Reference
p.3 “Accessing User Tools”
Downloaded From ManualsPrinter.com Manuals 
						

							Copier/Document Server Features
92
3Edit
This section describes the user tools in the Edit menu under Copier/Document
Server Features.
Default settings are shown in bold type.
Enter the width of the binding margin with the number keys as follows:
 Metric version: 0–30 mm (in increments of 1 mm)
 Inch version: 0-1.2 (in increments of 0.1 inch)
Enter the width of the erased margin with the number keys as follows:
 Metric version: 2–99 mm (in increments of 1 mm)
  Inch version: 0.1-3.9 (in increments of 0.1 inch)
An image of approximately 1.5 mm (0.06”) will not be displayed as the width of
the separation line, when specifying solid or broken lines.
❖Front Margin: Left / Right
You can specify left and right margins on the front side of copies in Margin
Adjustment mode.
The default setting is Left, 5 mm (Metric version) / Left, 0.2 (Inch version).
❖Back Margin: Left / Right
You can specify left and right margins on the back side of copies in Margin
Adjustment mode.
The default setting is Right, 5 mm (Metric version) / Right, 0.2 (Inch ver-
sion).
❖Front Margin: Top / Bottom
You can specify top and bottom margins on the front side of copies in Margin
Adjustment mode.
The default setting is T / B: 0 mm (Metric version) / T / B: 0.0 (Inch version).
❖Back Margin: Top / Bottom
You can specify top and bottom margins on the back side of copies in Margin
Adjustment mode.
The default setting is T / B: 0 mm (Metric version) / T / B: 0.0 (Inch version).
❖1 Sided→2 Sided Auto Margin: TtoT
 In 1 sided to 2 sided Duplex mode, you can specify the margins on the back
side.
The margin is set to the same value of “Back Margin: Left / Right”.
The default setting is Right, 5 mm (Metric version) / Right, 0.2 (Inch ver-
sion).
❖1 Sided→2 Sided Auto Margin: TtoB
In 1 sided to 2 sided Duplex mode, you can specify the margins on the back
side.
The value set for “Back Margin: Top / Bottom” is used.
The default setting is T / B: 0 mm (Metric version) / T / B: 0.0 (Inch version).
Downloaded From ManualsPrinter.com Manuals 
						

							Edit
93
3
❖Erase Border Width
You can specify the width of the erased border margins with this function.
The default setting is 10 mm (Metric version) / 0.4 (Inch version).
❖Erase Original Shadow in Combine
In Combine mode, you can specify whether to erase a 3 mm, 0.1 boundary
margin around all four edges of each original.
The default setting is On.
❖Erase Centre Width
You can specify the width of the erased centre margins with this function.
The default setting is 10 mm (Metric version) / 0.4 (Inch version).
❖Front Cover Copy in Combine
You can make a combined copy on the front cover sheet when you select
Front Cover mode.
The default setting is Combine.
❖Copy Order in Combine
You can set the copy order in Combine mode to Left to Right or Top to Bot-
tom.
The default setting is From Left to Right.
❖Orientation: Booklet, Magazine
You can select the orientation of copies to open when using Booklet or Mag-
azine mode.
The default setting is Open to Left.
❖Copy on Designating Page in Combine
You can specify whether to make a combined copy on the inserted slip sheets
in Desig./Chapter mode.
The default setting is Combine.
GCST019E
GCAH090E
Downloaded From ManualsPrinter.com Manuals 
						

							Copier/Document Server Features
94
3
❖Image Repeat Separation Line
You can select a separation line using the Image Repeat function from: None,
Solid, Broken A, Broken B, or Crop Marks.
None
 Solid
Broken A
Broken B
 Crop Marks
The default setting is None.
❖Double Copies Separation Line
You can select a separation line using the Double Copies function from: None,
Solid, Broken A, Broken B, or Crop Marks.
None
 Solid
Broken A
Downloaded From ManualsPrinter.com Manuals 
						

							Edit
95
3
Broken B
 Crop Marks
The default setting is None.
❖Separation Line in Combine
You can select a separation line using the Combine function from: None, Sol-
id, Broken A, Broken B, or Crop Marks.
None
 Solid
Broken A
Broken B
 Crop Marks
The default setting is None.
❖Copy Back Cover
When copying the back cover, you can specify whether to have the back cover
outside (outside page) or inside (inside page).
The default setting is Outside.
Reference
p.3 “Accessing User Tools”
“Booklet/Magazine”, Copy/ Document Server Reference
Downloaded From ManualsPrinter.com Manuals 
						

							Copier/Document Server Features
96
3Stamp
This section describes the user tools in the Stamp menu under Copier/Docu-
ment Server Features.
Reference
p.3 “Accessing User Tools”
Background Numbering
This section describes the user tools in the Background Numbering menu under
Stamp.
Default settings are shown in bold type.
❖Size
You can set the size of the numbers.
The default setting is Normal.
❖Density
You can set the density of the numbers.
The default setting is Normal.
Preset Stamp
This section describes the user tools in the Preset Stamp menu under Stamp.
Default settings are shown in bold type.
❖Stamp Language
You can select the language of the message printed in Stamp mode.
The default setting is English.
❖Stamp Priority
You can select the stamp type given priority when [Preset Stamp] is pressed.
The default setting is Copy.
❖Stamp Format
You can specify how each of stamp is printed.
Stamp Position
You can specify where to print the stamp.
The default setting is Top Right.
Downloaded From ManualsPrinter.com Manuals 
						

							Stamp
97
3
Stamp Position
You can adjust the position of the stamp within the available range as
shown below.
Metric version:
 “Top Left”…T/B: 4-144mm, L/R: 4-144mm
 “Top Centre”…T/B: 4-144mm, L/R: 72-72mm
 “Top Right”…T/B: 4-144mm, L/R: 4-144mm
 “Centre Left”…T/B: 72-72mm, L/R: 4-144mm
 “Centre”…T/B: 72-72mm, L/R: 72-72mm
 “Centre Right”…T/B: 72-72mm, L/R: 4-144mm
 “Bottom Left”…T/B: 4-144mm, L/R: 4-144mm
 “Bottom Centre”…T/B: 4-144mm, L/R: 72-72mm
 “Bottom Right”…T/B: 4-144mm, L/R: 4-144mm
Inch version:
 “Top Left”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Top Centre”…T/B: 0.1-5.7, L/R: 2.8-2.8
 “Top Right”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Centre Left”…T/B: 2.8-2.8, L/R: 0.1-5.7
 “Centre”…T/B: 2.8-2.8, L/R: 2.8-2.8
 “Centre Right”…T/B: 2.8-2.8, L/R: 0.1-5.7
 “Bottom Left”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Bottom Centre”…T/B: 0.1-5.7, L/R: 2.8-2.8
 “Bottom Right”…T/B: 0.1-5.7, L/R: 0.1-5.7
Size
You can set the size of the stamp.
The default setting is 1 X.
Density
You can set the pattern used to print the stamp.
Normal
The stamp is printed on the image. You cannot check which parts will
overlap.
Lighter
The image can be seen through the stamp.
Lightest
The image appears even clearer than in the Lighter setting.
The default setting is Normal.
 Page to Stamp
You can have the stamp printed on the first page or all pages.
The default setting is All Pages.
Reference
“Preset Stamp”, Copy/ Document Server Reference
Downloaded From ManualsPrinter.com Manuals 
						

							Copier/Document Server Features
98
3
User Stamp
This section describes the user tools in the User Stamp menu under Stamp.
Default settings are shown in bold type.
❖Program / Delete Stamp
You can register, change, or delete these designs as user stamps.
You can register up to four custom stamps with your favourite designs.
❖Stamp Format: 1, Stamp Format: 2, Stamp Format: 3, Stamp Format: 4
You can specify how each of registered User Stamps 1 to 4 is printed.
Stamp Position
You can specify where to print the User Stamp.
The default setting is Top Right.
Stamp Position
You can adjust the position of the User Stamp within the available range
as shown below.
Metric version:
 “Top Left”…T/B: 4-144mm, L/R: 4-144mm
 “Top Centre”…T/B: 4-144mm, L/R: 72-72mm
 “Top Right”…T/B: 4-144mm, L/R: 4-144mm
 “Centre Left”…T/B: 72-72mm, L/R: 4-144mm
 “Centre”…T/B: 72-72mm, L/R: 72-72mm
 “Centre Right”…T/B: 72-72mm, L/R: 4-144mm
 “Bottom Left”…T/B: 4-144mm, L/R: 4-144mm
 “Bottom Centre”…T/B: 4-144mm, L/R: 72-72mm
 “Bottom Right”…T/B: 4-144mm, L/R: 4-144mm
Inch version:
 “Top Left”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Top Centre”…T/B: 0.1-5.7, L/R: 2.8-2.8
 “Top Right”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Centre Left”…T/B: 2.8-2.8, L/R: 0.1-5.7
 “Centre”…T/B: 2.8-2.8, L/R: 2.8-2.8
 “Centre Right”…T/B: 2.8-2.8, L/R: 0.1-5.7
 “Bottom Left”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Bottom Centre”…T/B: 0.1-5.7, L/R: 2.8-2.8
 “Bottom Right”…T/B: 0.1-5.7, L/R: 0.1-5.7
 Page to Stamp
Sets whether to print the stamp on all pages or only the first page.
The default setting is All Pages.
Downloaded From ManualsPrinter.com Manuals 
						

							Stamp
99
3
Reference
“User Stamp”, Copy/ Document Server Reference
Date Stamp
This section describes the user tools in the Date Stamp menu under Stamp.
Default settings are shown in bold type.
❖Format
You can select the date format for Date Stamp mode.
The default setting is DD / MM / YYYY (Metric version) / MM / DD / YYYY
(Inch version).
❖Font
You can select the Date Stamp font.
The default setting is Font 1.
❖Size
You can set the Date Stamp size.
The default setting is Auto.
❖Superimpose
You can have the Date Stamp printed in white when it overlaps black parts of
the image.
The default setting is Off.
❖Stamp Setting
You can specify how Date Stamp is printed.
Stamp Position
You can specify where to print the Date Stamp.
The default setting is Top Left.
Stamp Position
You can adjust the position of the Date Stamp within the available range
as shown below.
Metric version:
 “Top Left”…T/B: 4-144mm, L/R: 4-144mm
 “Top Centre”…T/B: 4-144mm, L/R: 72-72mm
 “Top Right”…T/B: 4-144mm, L/R: 4-144mm
 “Bottom Left”…T/B: 4-144mm, L/R: 4-144mm
 “Bottom Centre”…T/B: 4-144mm, L/R: 72-72mm
 “Bottom Right”…T/B: 4-144mm, L/R: 4-144mm
Downloaded From ManualsPrinter.com Manuals 
						

							Copier/Document Server Features
100
3
Inch version:
 “Top Left”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Top Centre”…T/B: 0.1-5.7, L/R: 2.8-2.8
 “Top Right”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Bottom Left”…T/B: 0.1-5.7, L/R: 0.1-5.7
 “Bottom Centre”…T/B: 0.1-5.7, L/R: 2.8-2.8
 “Bottom Right”…T/B: 0.1-5.7, L/R: 0.1-5.7
 Page to Stamp
Sets whether to print the stamp on all pages or only the first page.
The default setting is All Pages.
Page Numbering
This section describes the user tools in the Page Numbering menu under Stamp.
Default settings are shown in bold type.
❖Stamp Format
You can select the page number format given priority when [Page Numbering]
is pressed.
The default setting is P1,P2....
❖Font
You can select the page number printed in Page Numbering mode.
The default setting is Font 1.
❖Size
You can set the size of the stamp printed in Page Numbering mode.
The default setting is Auto.
❖Duplex Back Page Stamping Position
You can set the position of the duplex back page number printed in Duplex
mode.
The default setting is Opposite Position.
❖Page Numbering in Combine
You can set page numbering when using the Combine function and the Page
Numbering function together.
The default setting is Per Original.
❖Stamp on Designating Slip Sheet
You can select to print the page number onto slip sheets when using the Des-
ignate function set to [Copy] and the Page Numbering function together.
The default setting is Off.
Downloaded From ManualsPrinter.com Manuals