Projector Christie Vivid Lx41 User Manual

21
BASIC OPERATION
Press FREEZE button on Remote Control Unit to freeze the picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button except the POINT, SELECT, RIGHT CLICK and LASER buttons.
Press NO SHOW button on Remote Control Unit to black out the
image. To restore to normal, press NO SHOW button again or press
any other button except the POINT, SELECT, RIGHT CLICK and
LASER buttons.
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
The message disappears after 4...

22
COMPUTER INPUT
Press MENU button and ON-SCREEN MENU will appear.  Press
the POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
Press the POINT DOWN button and a red-arrow icon will
appear.  Move arrow to RGB, and then press SELECT button.  
1
3
When connecting a computer output [5 BNC Type (Green, Blue, Red,
Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V
jacks.
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )
SELECTING COMPUTER SYSTEM
WHEN SELECTING  INPUT 1...

23
COMPUTER INPUT
This projector automatically detects different types of computer resolutions such as VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATIONS” on page 26).  When selecting Computer, this projector automatically
detects incoming signal and projects proper image without any special setting.  (Some computers need setting manually.)
Note : Projector may display one of following messages.
When projector can not recognize connected signal as
PC system provided in this projector,...

24
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically detect display signals from most personal computers currently distributed.  However, some
computers employ special signal formats which are different from the standard ones and may not be detected by the Multi-
Scan system of this projector.  If this happens, the projector can not reproduce a proper image and the image may be
recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture....

25
COMPUTER INPUT
NOTE : Fine sync., Total dots, Display area (H/V) and Full screen
can not be adjusted when “1035i (HDTV)” or “1080i (HDTV)”
is selected on PC SYSTEM Menu (P23).
Selects area displayed with this projector. Select the resolution in the
Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector.  Press the
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area H
Adjustment of vertical area displayed with this...

26
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
This projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 160
MHz of Dot Clock.
NOTE :Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x...

27
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear.  Press
the POINT LEFT/RIGHT button to move the red frame pointer to
IMAGE SELECT Menu icon.1
2Press the POINT DOWN button to move the red frame pointer to
level that you want to set and then press SELECT button.
Move the red frame icon to level
and press SELECT button.
Level being selected.
IMAGE SELECT MENU
Normal picture level preset on this projector.
Standard
Picture level with...

28
COMPUTER INPUT
Press the POINT LEFT/RIGHT but-
tons to adjust value.
Reset all adjustment to previous settings.
Reset
Store
Closes IMAGE MENU.
Quit
Other icons operate as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
the POINT LEFT/RIGHT buttons to move the red frame pointer
to IMAGE ADJUST Menu icon.1
2Press the POINT DOWN button to move the red frame pointer to
the item that you want to adjust and then press SELECT button.
The level of each item is displayed.  Adjust each level...

29
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen adjustment function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear.  Press
the POINT LEFT/RIGHT button(s) to move the red frame pointer
to SCREEN Menu icon.
When Digital zoom + is selected, ON-SCREEN MENU disappears
and the message “D. Zoom +” is displayed.  Press SELECT button to
expand image size.  And press the POINT UP/DOWN/LEFT/RIGHT
button(s) to pan the image....

30
VIDEO INPUT
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.Y,Pb/Cb,Pr/Cr
SELECTING INPUT SOURCE
Press MENU button and ON-SCREEN MENU will appear.  Press
the POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.1
Move the pointer to source
and press SELECT button.
Source Select Menu (VIDEO)
Move the pointer to source that you want to select and then
press SELECT button.3
When video input signal is connected to VIDEO jack,
select Video.Video
When...