Projector Christie Roadster S+14k M User Manual

							Section 4: Web User Interface
M Series User Manual4-9020-100009-07 Rev. 1 (07-2012)
Change Password
1. Select the user whose password you wish to change from the 
Users window.
2. Click Change Password to open the Password Change 
window.
3. Type the new password in the Password field.
4. Re-type the password in the Re-type Password field.
5. Click Ok to save or Cancel to ignore.
Delete User
1. Select the user that you wish to remove from the Users window
.
2. Click Delete User to open the Delete User window. A 
confirmation message appears.
3. Click Yes or No to proceed or ignore the action.
4.2.9 Advanced Tabbed Page - RTE
The RTE secondary tabbed page is where you can manage real-time events (i.e. add, delete, edit, copy and 
setup the GPIO) as described in the following section.
RTE Buttons
The real-time event buttons include the following:
•Add: Create a new event
•Delete: Remove one or multiple existing events
•Delete All: Remove all events
•Edit: Change or add information for an existing event 
•Copy: Clone an existing event
•Stop: Discontinue the event running
•GPIO Setup: Used to configure the GPIO pins as inputs/outputs and to set the current state of the output 
pins 
						

							4-10M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 4: Web User Interface
Add a Scheduled Event
1. Click Add to open the RTE Wizard.
2. Select the Scheduled Event tab. 
NOTE:
 The scheduled tab is always selected by default on add.
3. Select the frequency option for the event by selecting either Once, Daily, Weekly, or Monthly. 
NOTE: End Date is enabled when Daily, Weekly or Monthly repeat options are selected.
4. Click within the Start Time field to open a calendar pop-up window.
5. Navigate to and choose a desired date. The selected date will populate the Start Time field.
6. In the field below the Start Time field, enter a start time in the format “hr:min:sec”. The default is the 
current time.
7. Click Sync to set the computer and projector time to be the same; otherwise, the event will run based on 
the projector time. NOTE: Syncing the projector time to be that of your system time.
8. Enter a description of the scheduled event in the Description field. NOTE: Maximum of 100 characters.
9. Enter a serial command or a sequence of serial commands, with which you wish the projector to perform in 
the Command String box. 
• If a GPIO command string is needed, click the GPIO Output Helper button for instructions on how to 
create the command structure. 
NOTES: 1) The Output field contains 7 blocks which refer to the 7 I/O pins on the GPIO connector. Pin 
1 = +12V and Pin 5 = Ground. These are not included. 2) Clicking a block toggles between H, L, and X. 
3) If the Pulse check box is selected, those I/O Pins defined will pulse high or low. See 2.9.9 System Inte-
gration - GPIO Connector for detailed information. 4) Serial Representation box is read only.
• Click the Help button for a description of special RTE commands available for adding loops and delays 
to the command sequence. 
						

							Section 4: Web User Interface
M Series User Manual4-11020-100009-07 Rev. 1 (07-2012)
• Click the Test button to test the entered command string. 
NOTE: If the test passed or failed, a green or red icon appears to the right side of the Test button as 
shown.
10. Click Finish to create the added event. 
NOTES: 1) The added event appears in the RTE Listing window. 2) To activate or deactivate one or 
more RTEs listed in the RTE Listing window, select or clear each check box in the Active column 
accordingly.
Add a System Event
1. Click Add to open the RTE Wizard.
2. Select the System Event tab.
3. Select a type of event from the System Event drop-down list. 
NOTE: Depending on the selection made, additional selections are made available in the second drop-
down list located underneath (i.e. Input Change > Input 1, Slot 1)
.
Add a GPIO Event
1. Click Add to open the RTE Wizard.
2. Select the GPIO Event tab.
3. For the GPIO Event option define the Input 
Condition field as required. The Input 
Condition field contains 7 blocks which refer to 
the 7 I/O pins on the GPIO connector. Pin 1 = 
+12V and Pin 5 = Ground are not included or 
changed. 2) Clicking a block toggles between H, 
L, and X as shown. See 2.9.9 System Integration 
- GPIO Connector for detailed information. 
						

							4-12M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 4: Web User Interface
Add a Function Key Event
1. Click Add to open the RTE Wizard.
2. Select the Function Key Event tab.
3. Select a Function key from the drop-down list as 
shown. See Section 3 Operation for detailed 
information.
Add a DMX Channel Event
1. Click Add to open the RTE Wizard.
2. Select the DMX Channel Event tab.
3. Select a DMX channel (DMX-56 to DMX-61) 
from the drop-down list as shown in Figure. See 
Section 3 Operation for detailed information.
Add a Serial Command
1. Enter a serial command in the Serial Command 
field.
NOTE: For serial commands see the M Series 
Serial Commands Technical Reference 
Information P/N 020-100224-XX, available at the 
Christie Website.
2. Click Send to add the serial command.
About Tabbed Page
Provides information about the projector software version, model, serial number, and license information.
NOTE: The information provided on the Version and License tabs are read-only. 
						

							M Series User Manual5-1020-100009-07 Rev. 1 (07-2012)
 
5 Maintenance
Installers, service trained operators and all other users must maintain a safe operating environment at all times. 
Read through this section in its entirety and understand all warnings and precautions before attempting to 
operate this projector. 
5.1 Maintenance of the Cooling System
The high-intensity lamps and electronics rely on a properly functioning cooling system. Regular maintenance 
of the cooling system is critical to prevent overheating and sudden projector failure and helps ensure reliable 
operation. 
5.1.1 Ventilation
Vents and louvers in the projector covers provide ventilation, both for intake and exhaust. Never block or cover 
these openings. Do not install the projector near a radiator or heat register, or within an enclosure. To ensure 
adequate airflow around the projector, with a minimum clearance of 25cm (10”) on the left, right and rear sides 
of the projector from any walls or other obstructions. 
NOTE: Do not obstruct the air exchange to the projector. 
5.1.2 Optional Filters
  Use only special, high efficiency Christie approved filters. 
  This projector is not equipped with fan finger guards. Keep fingers away from
the fan blades when replacing filter.
Dust Air Filter
Check projector air dust filters, at minimum, 
every month. 
Dust air filters (if fitted), should be replaced whenever the lamp is replaced or between 200-500 hours, 
depending on use. A clogged air filter reduces air flow and can lead to overheating and failure of the projector. 
Check monthly by inspecting its color through the side vent grille with a flashlight. Replace grey colored 
filters. Leave the filters in their sealed packaging until ready for use.  
						

							5-2M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 5: Maintenance
Replace Air Filter:
1. Unscrew the 2 captive screws at the top of each filter 
door. Allow the door to rest down and away from the 
projector.
2. Slide the air filter out and replace, vacuum or wash 
the filter. Wash using mild soap and water. 
NOTE: Dry the filter before using.
3. Insert the new or cleaned air filter(s). 
4. Secure the filter door by tightening the 2 captive 
screws loosened in Step 1.
Fog Filter
Fog filters should be replaced after each use of the projector to a maximum of 20 hours. The life of the filter is 
approximately 20 hours based on environmental conditions. Leave the filters in their sealed packaging until 
ready for use. 
NOTE: The fog filters cannot be re-used or they will clog up with oil and the projector will overheat and 
shutdown. 
Replace Filters:
1. Unscrew the 2 captive screws at the top of each filter door. Allow the door to rest down, away from the 
projector.
2. Slide the filter (or dust air filter, if fitted) out.
3. Insert the new air fog filter with ensuring the white layer facing into the projector. 
NOTE: Each filter is a two-stage filter; the black activated charcoal layer faces out, and the white layer 
faces the projector. 
4. Secure the filter door by tightening the 2 captive screws loosened in Step 1.
5.2 Maintenance of Optics
5.2.1 Optical (Excluding Lens)
Unnecessary cleaning of optics, increases the risk of degrading delicate coatings and surfaces. Only clean 
optics when dust, dirt, oil, fingerprints or other marks are obvious and are causing performance problems. 
Maintenance of optical components requires a qualified service technician. Inspect exposed optical surfaces 
periodically in a clean, dust-free environment using a flashlight. 
Never touch an optical surface with your bare 
hands. Always wear latex lab gloves. 
						

							Section 5: Maintenance
M Series User Manual5-3020-100009-07 Rev. 1 (07-2012)
5.2.2 Supplies or Cleaning Optical Surfaces
• Soft camel-hair brush
• Dust-free blower - filtered dry nitrogen blown through an anti-static nozzle.
• Dust-free lens tissue, such as Melles Griot Kodak tissues (18LAB020), Opto-wipes (18LAB022), Kim 
Wipes or equivalent
•
For lens only. Lens cleaning solution, such as Melles Griot Optics Cleaning Fluid (18LAB011) or 
equivalent.
• Cotton swabs with wooden stems only
• Lens cleaning cloth/microfibre, such as Melles Griot (18LAB024) or equivalent
5.2.3 Cleaning the Lens
Check periodically. A small amount of dust or dirt on the lens has minimal effect on image quality. To avoid 
the risk of scratching the lens, clean only if absolutely necessary. 
Dust:
1. Brush most of the dust from the lens with a camel-hair brush and/or blow dust away with a dust-free 
blower.
2. Fold a microfibre cloth smooth and gently wipe remaining dust particles from the lens. Wipe evenly with 
the smooth portion of the cloth that has no folds or creases. Do not apply pressure with your fingers - use 
the tension in the folded cloth itself to collect dust.
3. If significant dust is still bound to the surface, dampen a clean microfibre cloth with coated optics cleaning 
solution (damp, not dripping). Wipe gently until clean.
Fingerprints, smudges, or oil:
1. Brush away most of the dust with a camel-hair brush and/or blow away using a dust-free blower.
2. Roll a lens tissue around a swab and soak it in coated optics cleaning solution. Tissue should be damp, but 
not dripping.
3. Gently wipe the surface using a figure-8 motion. Repeat this motion until the blemish is removed.
5.3 Replacing the Lamps
1. To turn off the lamps:
Turn off the lamps using the remote keypad or the built-in keypad with the lamp OFF command (see Step 
5) or by opening the lamp door. 
NOTE: The lamps will turn off automatically when the lamp door is open.  
						

							5-4M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 5: Maintenance
2. Use a #2 Phillips® screwdriver to turn the 1 captive 
screw on the lamp door counter-clockwise to access 
the lamp compartment. 
NOTE: When the door is open, the lamps will shut 
off. 
3. Wait at least 10 minutes before handling the lamps, to 
allow the lamps to cool.
4. Remove the old lamp.
a. Unscrew the 3 captive screws securing the lamp using a #1 Phillips® screwdriver.
b. Carefully remove the lamp from the projector. Place the old lamp in a location where it cannot fall or 
be bumped.
  Handle lamps with extreme caution. Dispose of lamps according to safety
regulations for your area.
5. To use lamp OFF command:
a. In the lamp menu, select Change Lamp. This will prompt for the old lamp serial number (if it was not 
previously entered).
b. Enter the new lamp serial number. 
NOTE: This action is not mandatory, it is recommended for accurate lamp statistics to be archived.
6. Install the new lamp:
a. Take precaution to align the new lamp properly in the correct orientation inside the projector.
b. Press firmly to seat the lamps, ensuring the lamp is secure.
c. Using the Phillips screwdriver and captive screws secure the lamp door and tighten the captive screw.
NOTES: 1) If the lamps were turned off with the OFF command in step 1, they will have to be manually 
turned on. 2) If the lamps were turned off by opening the door, then they will automatically turn on again 
when the door is closed. 
						

							M Series User Manual6-1020-100009-07 Rev. 1 (07-2012)
6 Troubleshooting
If the projector is not operating properly, note the symptoms and use this section as a guide to resolve the 
problem. If the problem cannot be resolved. contact your dealer for assistance. 
NOTE: A Christie accredited service technician is required when opening an enclosure to diagnose any 
“probable cause”. 
6.1 Power
6.1.1 Projector Does Not Power ON
1.Ensure projector is plugged in: Check power switch above power cord is in the ON position.
2.Check that the Status LEDs are ON: While the projector is busy initializing, the LEDs should be 
cycling. When finished initializing, the Power and Shutter LEDs (the two on the right) should be on. 
3.Check the LCD display: While the projector is busy initializing, the display should show “Please wait”. 
When finished initializing, the display should show “Standby mode”.
4. Check the LCD display for any warnings or errors.
NOTE: A condition occurs on the first power on after a software upgrade, and is indicated by all the 
following:
• The Status LEDs are cycling green
• The LCD displays the warning “Image Processor Upgrading”
• The LED on the Image Processor card flashes green
• The Web page shows a warning that the Image processor card is upgrading.
When this occurs, the projector should not be AC power cycled and the Image Processor card should not be 
removed. This operation may take as long as 5 minutes to complete.
6.2 Lamp 
6.2.1 Lamp Does Not Ignite
1.Check for an interlock failure: Check the LCD display for an error. If the other lamp has ignited and an 
image can be seen, use the remote keypad and check the Status menu for any errors and for the Lamp door 
interlock status. If not lamp has ignited, use the Virtual OSD on the web interface to check these items. The 
interlock failure could be an open lamp door or a failed lamp fan.
2. Using the remote keypad or Virtual OSD as above, check the lamp mode in the Lamp menu. This may be 
set to a single lamp or dual lamp mode. Check in the Status menu what the reported mode is.
3. For suspected communication failures, power-down the projector and try again.
4. If the lamp does not ignite after the second attempt and after powering down and up again (complete AC 
power down, then replace the lamp. 
						

							6-2M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 6: Troubleshooting
6.2.2 Lamp Suddenly Turns OFF
1. Check lamp power through the remote keypad checking the Lamp menu or from the web user interface 
Advanced: Lamp menu. Try increasing lamp power. 
2. Check for an alarm condition on the LCD keypad display.
3. Replace the lamp.
6.2.3 Flicker, Shadows Or Dimness
1. Check lamp power through the remote keypad checking the Lamp menu or from the web user interface 
Advanced: Lamp menu. Try increasing lamp power. 
2. Replace the lamp.
6.3 LCD 
6.3.1 Blank Screen, No Menu Display 
Press any arrow key on the built-in keypad. The backlight on the LCD and the backlight for the built-in keypad 
should turn on. If the LCD is still blank, restart the projector.
6.4 Remote Keypad
6.4.1 Remote Keypad Does Not Seem to Work
1. Replace the batteries. 
2. Check if IR signals are received by the projector. Pressing any key on the remote control towards the front 
or rear sensor, the Status LED will blink, regardless if any command is executed. If the LED does not 
blink, restart the projector.
3. Ensure the remote keypad is enabled. If the projector is powered, using the built-in keypad, open the OSD 
menu and go to the Main Menu > Configuration > Communication submenu and check the check boxes 
for Front IR Enabled and Rear IR Enabled are enabled. Enable them if they were disabled and try again.
4. Projector is busy. If the projector is busy in a warm-up mode or in a cool-down mode, the commands from 
the remote keypad may be ignored. Wait until the projector reaches a stable state (Power ON or Stand By) 
and try again.
5. Press the PROJ key on the remote keypad. If this brings up a pop-up box on the OSD, ensure that the 
check box is marked to enable the projector.
6. Using the XLR connector, use the remote as a “wired” keypad. If it does work and all the IR sensors have 
been enabled, then there may be a problem with the IR sensors.