Projector Christie Roadster S+14k M User Manual

Section 2: Installation and Setup
M Series User Manual2-31020-100009-07 Rev. 1 (07-2012)
FIGURE 2-8 1X3 WIRING SOLUTION
FIGURE 2-9 2X2 WIRING SOLUTION
FIGURE 2-10 2X3 LOOP-THROUGH WIRING SOLUTION 

2-32M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
FIGURE 2-11 2X3 SINGLE WIRING LOOP-THROUGH - NO PIP IS SUPPORTED
FIGURE 2-12 3X3 LOOP-THROUGH WIRING SOLUTION 

Section 3: Operation
M Series User Manual3-1020-100009-07 Rev. 1 (07-2012)
3 Operation
This section describes the controls and switches used for basic projector operation once it is properly installed, 
aligned and configured by a Christie accredited service technician. 
  See the Safety Warnings and Guidelines in
 1.4 Safety Warnings and Guidelines.
3.1 How to Use the Remote Keypad or Built-In Keypad
The projector is typically controlled using one of the following keypads:
•Remote Keypad: For wired or...

3-2M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 3: Operation
3.1.2 Remote Keypad
FIGURE 3-1 REMOTE KEYPAD 

Section 3: Operation
M Series User Manual3-3020-100009-07 Rev. 1 (07-2012)
Table 3.1 M Series Key Commands
KEYKEY DOWN VALUEKEY UP VALUE
0 0 128
1 1 129
2 2 130
3 3 131
4 4 132
5 5 133
6 6 134
7 7 135
8 8 136
9 9 137
- (Func) 14 142
Help 63 191
Gamma 85 213
Contrast 41 169
Brightness 80 208
Channel 81 209
Proj 22 150
Arrow Down 59 187
Arrow Left 60 188
Arrow Right 62 190
Arrow Up 58 186
Enter 13 141
Menu 44 172
Exit 27 155
PIP 84 212
Swap 89 217
Input 64 192
OSD 47 175
Slot 1 65 193
Slot 2 66 194
Slot 3...

3-4M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 3: Operation
3.1.3 Wired Remote
You can convert the remote keypad into a wired remote keypad using the cable provided with the projector. 
Connect one end into the remote and the other to the XLR connector on the input panel labeled as wired 
keypad. The wired remote is recommended when:
• The built-in keypad is inaccessible
• The lighting conditions are unsuitable for proper IR transmission 
NOTE: Leave the batteries in the wired remote for...

Section 3: Operation
M Series User Manual3-5020-100009-07 Rev. 1 (07-2012)
•Power Key: Used to switch from Standby mode to ON, and from ON to Standby mode; LED always 
remains Amber
•Help Key: Only available in the On Screen Display (OSD) context; LED is Amber when the menu is being 
displayed on the projected image display; when no menu is being displayed, the Help key is still enabled if 
the OSD is enabled. It is only disabled when the entire OSD is set to OFF.
•Auto Key: Enabled state when the power...

3-6M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 3: Operation
Table 3.2 Auto Setup
The best auto setup will be obtained under the following conditions:
• Input levels, it is best to have an image with saturated (very bright) colors.
• Phase, high contrast edges are needed.
To determine active window size:
• Video images should have whites and blacks in the image.
• Wide range video images should have content (including white) that extends to all edges of the image.
See 3.4 Adjusting the...

Section 3: Operation
M Series User Manual3-7020-100009-07 Rev. 1 (07-2012)
Bright
Increases or decreases the black level in the image. Use L
EFT/RIGHT ARROW KEY until you reach the desired 
level of brightness. For best results, start high and decrease so that dark areas do not become fully black (i.e., 
“crushed”). Conversely, overly high brightness changes black to dark grey, causing washed-out images.
Gamma
Determines how grey shades are displayed between minimum input (black) and maximum input...

3-8M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 3: Operation
ARROW KEY (open) to guarantee the correct state (useful if you are unsure of the present state). Alternatively, 
press S
HUTTER, SHUTTER to toggle from the present on/off state. 
A closed shutter blanks the display (turns it to black). Close the shutter to block the displayed image while 
maintaining access to projector functions. Opening the shutter restores the image. 
NOTES: 1) The LCD display shows the current state of the...