Projector Christie Roadster S+14k M User Manual

Section 6: Troubleshooting
M Series User Manual6-3020-100009-07 Rev. 1 (07-2012)
6.5 OSD 
6.5.1 The OSD Menu Does Not Display 
• Using the LCD, ensure that OSD menu is enabled, scroll-down until the item OSD appears. The LCD shows 
“OSD: off”. Press and hold the OSD soft key on the built-in keypad. The LCD now shows “OSD on” then 
press the menu key on the remote keypad.
-OR-
• Press and hold the OSD key on the remote keypad for 2-3 seconds, then press the menu key.
6.6 Ethernet
6.6.1 Can Not Establish...

6-4M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 6: Troubleshooting
6.7.4 The Display is Jittery or Unstable
1. If the display is jittery or blinking erratically, ensure that the source is properly connected and of adequate 
quality for detection. With poor quality or improperly connected source, the projector will repeatedly 
attempt to display an image, however briefly.
2. The horizontal and vertical scan frequency of the input signal may be out of range for the projector. See 
Section 7...

Section 6: Troubleshooting
M Series User Manual6-5020-100009-07 Rev. 1 (07-2012)
6.7.12Colors in the Display are Inaccurate
1. The color, tint, color space and/or color temperature settings may require adjustment at your input source. 
2. Try Auto Setup.
3. Ensure signal connections are correct.
4. Ensure the proper channel for this source is being used.
6.7.13Display is Not Rectangular
1. Check leveling of the projector. Ensure the lens surface and screen are parallel to one another.
2. Is the vertical...

6-6M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 6: Troubleshooting
6.8.2 A Backup Or Interrogator File Cannot Be Saved
After performing a backup of Interrogator, you may be prompted from a pop-up window before saving the file. 
If you have not specifically set Internet Explorer to automatically open/save the file without prompting, and if 
pop-up windows have been disabled (by enabling the pop-up blocker), then you will not be able to save the 
file.
Disable the pop-up blocker from Main >...

M Series User Manual7-1020-100009-07 Rev. 1 (07-2012)
7 Specifications
This section provides detailed M Series features; including inputs, lamp, and power requirements. 
NOTE: Due to continuing research, detailed features are subject to change without notice.
7.1 Image Performance 
7.1.1 Pixel Format 
7.1.2 Brightness (ANSI Lumens) 
1080p (H x V square pixels)         1920 x 1080
SXGA+ (H x V square pixels) 1400 x 1050
WUXGA (H x V square pixels) 1920 x 1200
WXGA (H x V square pixels) 1366 x 768...

7-2M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 7: Specifications
7.1.3 Contrast
7.1.4 Luminance Uniformity
7.1.5 Color Uniformity
7.1.6 Color Primaries
7.1.7 Gamma
7.1.8 Grayscale/Color Resolution
ANSI: 16 pt. checker pattern on black screen 650:1 typical
Full field: 9 pt. average ON/OFF with background light 
subtraction2500:1 typical (full open aperture) 1080p
2100:1 typical (full open aperture) SXGA+
2100:1 typical (full open aperture) WUXGA
2100:1 typical (full open aperture) WXGA...

Section 7: Specifications
M Series User Manual7-3020-100009-07 Rev. 1 (07-2012)
7.1.9 Color Temperature
7.1.10Convergence
Convergence zones A, B, C are as defined in Figure 2. Zone A has a diameter ¼ of the image height. Zone B 
has a diameter of full image height. All specified convergence errors are between any two colors after a 
minimum warm-up of 30 minutes. 
Convergence is specified with a 1.4-1.8 HD lens (part number 118-100112-01) in the 1.4:1 position with zero 
offset. Bore-sight alignment must...

7-4M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 7: Specifications
7.1.11Blemishes
Blemishes are to be observed at 1 full screen height distance from the image for a period of 30 seconds. Screen 
size: 10 foot wide for 350W models, 8 foot wide for 200W models. Blemishes are defined as per TI 
Specification 2506811.
7.1.12Pixel Defects
7.1.13Image Artifacts
7.1.14Picture Centering (with 1.4-1.8:1 HD lens)
7.2 Feature Set
7.2.1 Airflow 
7.2.2 Air Filters (Optional)
Red screen No blemishes...

Section 7: Specifications
M Series User Manual7-5020-100009-07 Rev. 1 (07-2012)
7.2.3 Dust Sealing
7.2.4 ILS (Intelligent Lens System)
7.2.5 Projection Lens Compatibility
Dust sealed DMDs         Gasket sealed
Dust sealed illumination system  Sealed from lamp input to entrance face of prism 
when lamps are installed
Motorized lenses and lens mount with position encoding        Zoom, focus, horizontal and vertical offsets
Accuracy ±2 pixel
Manual control 1/3 pixel fine movement control per button press on...

7-6M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 7: Specifications
7.2.6 Dynamic Iris 
7.2.7 Automatic Fans
7.2.8 Automatic Color Filtering
7.2.9 Constant Lamp Output Management
7.2.10Shutter 
7.2.11Lamps
Motorized iris with position feedback        Scene controlled motorized iris automatically 
adjusts to image content
Max frequency open-close-open 20 Hz
Sound level Within ambient noise level of projector
Configurable per channel
Temperature sensitive fan speed control Fans automatically...