Projector Christie Roadie X10 User Manual

OPERATION
3-16
Roadie S12/X10 User’s Manual
Double slidebars - In double
slidebars, such as the pixel
tracking/pixel phase double
slidebar, adjust the top slidebar
with 
 or  as desired.
When you have finished with the
top slidebar (whether changed or
not), adjust the bottom slidebar
with 
ON or OFF. When you are done, press Exi t to return to your presentation. For
fast continuous adjustments, hold down the desired arrow key.
“Direct” slidebars - For quick access, you can often use a slidebar (or...

OPERATION
Roadie S12/X10 User’s Manual3-17
Figure 3.6. Example of Pull-Down List
Or, if you prefer to quickly scroll through a list without first pulling it down,
highlight the option and use 
 or . Press Enter when the desired choice appears.
NOTES: 1) Press 
 or  to jump between “pages” in an extra long pull-down
list. 2) Press 
Exi t while in a pull-down list to cancel any change.
ACTIVATE THE EDIT WINDOW: To enter or edit text, highlight the desired parameter
(such as a channel name) and press 
Enter...

OPERATION
3-18
Roadie S12/X10 User’s Manual
Enter numbers directly from the keypad in order to specify numbers representing
projectors, channels (source setups), switchers, or slots. As each digit is entered, it is
displayed and the cursor moves on. Note that channel numbers are defined with 2
digits—for example, if you enter only a single digit (like “7”) for a channel number,
the channel will automatically be defined as “07”. Use “07” to utilize this channel.
NOTES: 1) Once you enter the first digit,...

OPERATION
Roadie S12/X10 User’s Manual3-19
If more than one channel exists for the input, the image will be displayed according
to the setup parameters for the first channel with matching characteristics.
CHANNEL - A channel is a collection of measurements, locations and settings that
tailor a display to your specific needs. Since source types and applications can vary
greatly, you will likely want to adjust and define a wide variety of parameters, such
as brightness, contrast, tint, size, etc., in order...

OPERATION
3-20
Roadie S12/X10 User’s Manual
USING A CHANNEL: You can normally select a channel at any time by pressing Chan
(see right). If you want to
prevent a channel from
appearing in this list, you
must edit the channel as
described in Channel Edit
later in this section. Such a
channel can still be
selected by entering its
number as shown at right.
NOTES: 1) The current channel is highlighted upon entering the channel list, or, if
this channel is not displayed here, the first channel in the list is...

OPERATION
Roadie S12/X10 User’s Manual3-21
Table 3.1. Abbreviations for Signal Type
Abbrev.Signal Type
4WH Composite (4 wire) on HC input
4WV Composite (4 wire) on V input
SG Sync-on-green
SR Sync-on-red
5W Separate H,V
5WR Separate H,V swapped
SVid S-Vid
CVid Composite Video
3LH Tri-Level on HC input
3LV Tri-Level on V input
3LG Tri-Level on green
E3LH European Tri-Level on HC input
E3LV European Tri-Level on V input
E3G European Tri-Level on green
Dig Digital
FUNCTIONS WITHIN THE CHANNEL SETUP MENU —To...

OPERATION
3-22
Roadie S12/X10 User’s Manual
Figure 3.10. Deleting a Channel
TO DELETE MULTIPLE CHANNELS, highlight any channel in the Channel Setup menu
and press 
Fu nc to go to the Channel Copy/Delete submenu. Select “Delete Unlocked
Only” and press 
Enter to delete all unlocked channels. Or select “Delete All Channels”
to delete all channels, even those that are locked. In either case, the current channel
will remain but will be redefined from projector defaults.
NOTE: For any deletion, a confirmation...

OPERATION
Roadie S12/X10 User’s Manual3-23
message appears indicating that this number is already in use–assign a
different channel number.
• 
SWITCHER NUMBER: “0” represents the projector itself. Or, if the input
source is connected to a switcher, the default will be the lowest switcher
number available (from 1-9)–change here as desired.
• 
SLOT: 1 (Input1), 2 (Input2), 3 (Input3), or 4 (Input4) for projector inputs, or
current slot number (1-9) if the source is connected to a switcher.
• 
LOCKED: If...

OPERATION
3-24
Roadie S12/X10 User’s Manual
If you want the projector to quickly set up the image for you, select “Auto Setup”
from the Main menu. A confirmation box will ask if you really want to continue, in
which case display parameters listed in Table 3.2 below will be set for you. An “Auto
Setup” can save time in setting up an image, and you can also make further
adjustments as desired. You must have an unlocked channel present to use Auto Setup.
Table 3.2. Auto Setup
What an “Auto Setup” Does...

OPERATION
Roadie S12/X10 User’s Manual3-25
manually. Resizing options for non-tiled applications are explained in detail below.
WHAT IS THE PROJECTOR’S DEFAULT? When displaying a new source, by default
your image will fill the screen as fully as possible for the type of source present. See
Select “Default” below.
WHEN “CUSTOM” APPEARS: The “Custom” descriptor automatically appears in the
Size and Position menu when any of the values for Size, Vertical Stretch, H-Position,
V-Position or Blanking do not...