Projector Christie Roadie S12 User Manual

THROW DISTANCE
E-6
Roadie S12/X10 User’s Manual 

THROW DISTANCE
Roadie S12/X10 User’s ManualE-7 

Appendix F
Optional Input Modules
Roadie S12/X10 User’s ManualF-1
There are many optional input modules and accessories currently available for this projector. Contact your dealer for a
complete and up-to-date listing.
The Marquee Signal Switcher is a rack-mountable signal selector which can greatly
increase the number of analog sources (inputs) available to the projector. Connected
to 
INPUT 1, a single switcher provides up to 9 more sources for the projector.
Additional Marquee Signal Switchers can be...

OPTIONAL INPUT MODULES
F-2
Roadie S12/X10 User’s Manual
Features
◊ accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or
separate horizontal and vertical sync), up to 500 MHz bandwidth
◊ BNC connectors for RGB signal inputs
NOTE: The audio connectors are not functional. Connect audio to an external audio
system.
The RGB400 Buffered Amplifier Input Module may be installed in a Marquee Signal
Switcher or a Marquee Case/Power Supply. Connect three-, four-, or five-wire RGB
video signals of up...

OPTIONAL INPUT MODULES
Roadie S12/X10 User’s ManualF-3
The Composite/S-Video Input Module may be installed in this projector, a Marquee
Signal Switcher or a Marquee Case/Power Supply. The module receives either
composite video or S-video input signals from tape or disk players (do not connect
both types of signals simultaneously). Video inputs are 75
S  terminated. Video
outputs are provided for buffered loop-through to another display device.
Features
◊ BNC connectors for composite RGB signals
◊ 4-pin...

OPTIONAL INPUT MODULES
F-4
Roadie S12/X10 User’s Manual
The DVI Input Module can be installed in the projector to display digital video input
signals conforming to the DVI (Digital Visual Interface) standard (single-channel).
Features
◊ Supports Digital Visual Interface (DVI) single-channel
◊ Supports VESA Extended Display Identification Data (EDID)
◊ Provides an active-loop-through using a DVI connector (conforming to the
DVI Specification)
The Digital HDTV Module can be installed in the projector at...

OPTIONAL INPUT MODULES
Roadie S12/X10 User’s ManualF-5
SERIAL IN BNC connector. The signal can loop through the SERIAL OUT BNC out to
another device (such as another projector). Inputs are 75
S  terminated.
Features
◊ accepts serial digital 4:2:2 component video (YCbCr)
◊ provides both a 
SERIAL IN and a SERIAL OUT BNC connector
◊ includes status LEDs for signal and error
NOTE: Connect audio to an external audio system.
The Marquee Case/Power Supply enables you to use an analog input module as a...

Index
Roadie S12/X10 User’s ManualINDEX-1
A
AC Requirements, 2-1, 5-3
Advanced 10-bit (ADP), 3-39
Noise and Filtering, 3-40
Anamorphic, 3-26
And Tiled Image, 3-52
Arrow Keys, 3-9
Auto Gain Control. See Enable Decoder AGC
Auto Input Level, 3-36
Auto Setup, 3-24
AutoSource Checkbox, 3-23
B
Back IR Keypad, 3-44
Bad Sync, 3-53
Baud Rate, 2-25, 3-44
Blacklevels and Drives, 3-37
Brightness, 3-30
Brightness Key, 3-10, 3-30
Brightness Specification, 5-1
Broadcast Key, 3-45
Broadcasting, 3-11, 3-50
C
Calibrate...