Polaroid Projector Polaview 220 User Manual

Focusing and zoomingFocus the projected image with the FOCUS control either 
the imageon the control panel or remote control. Adjust the image
size by using the ZOOM control on the control panel or
remote control.
Keystone correctionA keystone correction of 17 degrees is built into the 
projector to compensate for image distortion. You may
want to adjust the rear feet of the projector to position 
the image on the screen. 
Image sizeThe projector 20–30mm (1.5:1) motorized zoom/focus lens
provides a...

Control-panel keys
The control-panel keys are used to adjust the projected
image and to display and hide the menus.
Control-panel keys
Key Function
IMAGE Provides access to menus for 
control of brightness, contrast, tint,
phase, and sharpness of the 
projected image.
SOUND Controls the volume, balance, 
treble, and bass of the 
source
connected to the projector. 
SET UP Controls front, rear, table-top, 
ceiling-mount modes of projection;
language; and factory-setting
defaults.
Using the projector19...

Key Function
ENTER L & R Nonfunctional keys, reserved for
future product development.
Cursor pad Controls on-screen menus and
increases or decreases setting 
levels. 
MUTE Turns the audio on or off.
CURTAIN Toggles between a displayed image
and a blank blue screen.
POSITION Allows positioning of the displayed
image, when used with the cursor
pad.
VOLUME +/- Decreases or increases the volume.
ZOOM +/- Zooms in and out. Press + to make
the picture larger. Press - to make
the picture smaller.
FOCUS +/-...

Standby modeUse the Standby mode to prolong the life of the projector
lamp. When you select the Standby mode by pressing the
LAMP key, the green LED power indicator on the rear panel
of the projector begins to blink and continues to do so for 
3 minutes, to allow the projector to cool down. The projec-
tor must complete this 3-minute cool-down period before it
can resume normal operation. The green LED resumes its
normal steady glow at the end of 3 minutes. Press the
LAMP key again to resume operation of...

22Using the projector  
The remote control
Key Function
aLaser pointer Serves as a pointing device.
bSOUND Controls the volume, balance, treble,
and bass of the 
sourceconnected to
the projector. 
cIMAGE Provides access to menus for control
of brightness, contrast, tint, phase,
and sharpness of the projected
image.
dLASER Toggles the laser pointer on and off.
eMUTE Turns the audio on or off.
fCURTAIN Toggles between a displayed image
and a blank screen.
gPOSITION Allows positioning of the displayed...

Key Function
hSET UP Controls front, rear, table-top, 
ceiling-mount modes of projection;
language; factory-setting defaults;
and video mode.
iENTER L & R Performs previous or next functions,
when used with the computer IR
receiver kit.
jCursor pad Controls on-screen menus and
increases or decreases setting levels. 
kVOLUME +/- Decreases or increases the volume.
lZOOM +/- Zooms in and out. Press + to make
the picture larger. Press - to make the
picture smaller.
mFOCUS +/- Adjusts the focus of the image....

24Using the projector  
Menu selections
IMAGE menuSelect the IMAGE menu to control the brightness, contrast,
tint, phase, and sharpness of the projected picture.
Option What it does
BRIGHTNESS Increases or decreases the intensity
level of the projected image.
CONTRAST Adjusts the contrast of the projected 
image.
TINT Adjusts the red or green color balance
of the projected image.
SHARPNESS Eliminates horizontal disturbance 
from the computer video signal.
PHASE Eliminates vertical bars from
computer...

SETUP menuSelect the SETUP menu to make adjustments to the 
following settings:
Option What it does
PROJECTION (FRONT/REAR) Selects the projected 
display orientation for front
or rear projection mode.
LOCATION (TABLE/CEILING) Inverts the projected image 
orientation for use with a 
ceiling mount.
LANGUAGE  Converts the on-screen 
menus from English to 
French, German, Spanish.
FACTORY SETTINGS Resets all adjustments to 
the factory-default settings.
VIDEO MODE Selects either PAL or
SECAM operation.
If...

26Using the projector  
Image optimization
Making adjustments Use the projector SETUP and IMAGE menus to adjust the 
to settings settings to fine-tune your projected image.
Your projector factory-default settings are designed 
to configure it with your computer and video sources 
automatically to provide a high-quality projected image.
Because of operational differences between the projector
and computer and video sources, you may want to make
minor setting adjustments to optimize your displayed
image....

Eliminating Examine the projected image for horizontal noise bars or 
horizontal noisejittering around text or icons. Use the SHARPNESS option to
eliminate them:
1From the projector control panel or remote control, press
the IMAGE menu key.
2Using the cursor pad, scroll through the menu selections
and highlight SHARPNESS on the on-screen menu display.
3Use the left () key on the cursor pad to
eliminate the horizontal noise bars. Adjust the SHARPNESS
setting until the horizontal noise bars or jittering...