Polaroid Projector Polaview 220 User Manual

2 Detailed setup
Your Polaview Model 220 Projector
This chapter describes setup procedures for connecting
your Polaview Model 220 Projector to a compatible 
computer. It also provides instructions on how to set up 
the projector for use with various video sources.
Before you begin, examine the components of the
projector.
The Polaroid Polaview
Model 220 Projector 
and remote control
aControl panel
bInfrared sensor
cLamp assembly door latch
dProjection lens assembly
eHandle
fRemote control
D LP
123 4
a
c...

The Polaroid Polaview
Model 220 Projector –
rear view
gConnector panel
hGreen LED power indicator
iAC power switch
jPower-cord receptacle
8Detailed setup
LR SOURCE  1
VIDEO INPUTSL R STEREO
MAC / PCSTEREO
PC / MACSTEREO
REDRIVELR
RS 232 SOURCE  2SOURCE  3SOURCE  4OUTPUTS
COMPUTER INPUTS
g
i
j
h 

Getting started
Positioning the Place the projector on a solid, flat surface at a right angle 
projector(perpendicular) to the projection screen and parallel to the
floor. If you use a media cart, make sure the wheels are
locked to prevent it from moving. 
Opening the casing of your projector could damage the
components inside and will void your warranty. Dropping 
or mishandling the projector can damage the optical path. 
Ceiling mountThe projector is capable of displaying inverted images 
for ceiling...

Connector panel
All connections between the projector and your computer or
video source are made on the rear connector panel.
The connector panel
Note:Whenever you connect the projector to a computer or
video source for the first time, the projector defaults to the
factory settings. Due to operational differences between
computers and video sources, it may be necessary to make
minor adjustments to the settings. See 
Image optimization
in Chapter 4, Using the projectorfor more information. The
projector...

Computer and VCR connections
Connecting IBM PCs Place the projector on a tabletop or other level surface 
and compatibleswith the lens facing the projection screen.
1Connect your computer to the projector with the VGA/Mac II
reversible cable (part number CA18). Plug the end labeled
“To VGA” into the monitor port of your computer. Plug the
other end into the “PC/MAC” port of the projector (see the
illustration below).
IBM connections
2If you want to be able to view your computer monitor and
project images...

Connecting Mac II,  Place the projector on a tabletop or other level surface 
Quadra, LC, and with the lens facing the projection screen.
Powerbook and 
compatibles
1Connect your computer to the projector with the VGA/Mac II
reversible cable (part number CA18). Plug the end labeled
“To Mac” into the computer monitor port. Plug the end
labeled “To VGA” into the projector “MAC/PC” port (see the
illustration below). 
Macintosh connections
2If you want to be able to view your computer monitor and
project...

Detailed setup13
NTSC/PAL/SECAMPlace the projector on a tabletop or other level surface 
video connectionswith the lens facing the projection screen.
1Connect one of the yellow RCA composite video cable 
(part number CA19) plugs into the VIDEO OUT jack of your
video source. Connect the yellow plug at the other end of
the cable to either of the SOURCE 1 or SOURCE 2 video-
input composite jacks (yellow) on the projector connector
panel (see the illustration below). 
Composite video 
connections
The...

3Connect the white RCA audio-video cable plug to the 
AUDIO L (left) jack of your audio source. Then connect the
white plug at the projector end of the cable to a white audio
jack (either SOURCE 1 or SOURCE 2 L) on the projector rear
panel.
S-video connections
Note:Whenever you connect the projector to a computer or
video source for the first time, the projector defaults to the
factory settings. Due to operational differences between
computers and video sources, it may be necessary to make
minor...

Supplying power to the projector
After you connect the projector to your computer or video
source, connect the power cord to the projector. The power-
cord receptacle and AC power switch are located below the
connector panel on the rear side of the projector.
Power receptacle 
and AC power 
switch
aPower receptacle 
bAC power switch
To supply power to the projector:
1Plug the appropriate power cord into the power receptacle
on the rear panel of the projector.
2Connect the power cord to a...

Turning on the projector
Turn on the power switch located on the rear panel of 
the projector, beside the power port. After approximately 
30 seconds after the power is on, a solid blue image is 
projected onto your screen. Whenever the power is on, 
the green LED power indicator on the rear panel of the 
projector glows a steady green.
Note:You can detect a high-pitched sound as the color-
wheel and fans are reaching operating speed. Also, when
you turn on the projector, you can detect a slight,...