Plus Projector V3 131 User Manual

E-51
Lamp Mode
Use this if the picture is projected on a small screen and the picture is
too bright or when projecting images in dark rooms.
Select the item name “Lamp Mode” and select the setting contents with the
SELECT  buttons.
Eco ............. The lamp’s brightness is reduced to approximately 80%, extending the
lamp’s service life.
(STATUS indicator is green)
Normal ....... The lamp brightness is set to 100% and the screen is bright.
(STATUS indicator is off)
Note:
Frequent switching this mode...

E-52
Presentation Timer
The presentation is given while checking the timer displayed on the
screen.
The gauge display allows the remaining time to be known at a glance.
Select the item name “Presentation Timer” and select the setting contents
with the SELECT  buttons.
Setting contents:Off, 10 min. , 20 min. , 30 min. , 40 min. , 50 min. , 60 min.
To start the timer...
Press the MENU button and open the menu.
The timer display will appear at the lower right and the timer will start.
See “Using the...

E-53
Language
This function sets the language that is displayed on screen in
the messages and menu displays.
Select item name “Language” and press the ENTER button to open
the Language sub menu.
Select the language with the SELECT 
 buttons.
On Screen
This function switches on/off the messages displayed with a black
frame such as the input signal information and the aspect ratio.
Select item name “On Screen” and select the setting contents with the
SELECT  buttons.
On ............... The message is...

E-54
Startup Screen
This is the selection of whether or not to display the logo screen
at startup time.
Select item name “On Screen” and select the setting contents with the
SELECT  buttons.
Logo ........... Displays the logo.
Blank .......... Does not display the logo.
Note:
When “Logo” is selected at the startup screen, the “PLUS” logo is dis-
played.
Option
Security Lock
A password can be registered and the security lock set in order
to prevent unauthorized use of the projector.
For instructions on...

E-55
Info.
•Select menu name “Info.”.
See “Menu Operation Method” on Page E-36 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-41.
Status
This displays information about the equipment.
Select item name “Status” and press the ENTER button.
There is a change to the status display.
Press the CANCEL button to return to the menu.
Display Contents:
Projector...

E-56
Resolution / Frequency
This function displays the resolution and frequency of the detected in-
put signal.
Lamp Timer
This displays the lamp timer.
This projector has an Eco mode function. The lamp life will differ between
Normal mode and Eco mode.
Lamp Life
Use only in Normal mode: approx.1500 hours
Use only in Eco mode: approx.2000 hours
* Lamp life will differ when there has been switching between the modes.
•When Lamp Life Has Been Reached
“Replace the Lamp Cartridge” is displayed on the screen...

E-57
When an Indicator is Lit or Flashing
STANDBY
AUTO
RCE STANDBY
STATUS
STANDBYSTATUS
STATUSSTANDBY
STATUSSTANDBY
STATUSSTANDBY
STATUSSTANDBY
The indicators on the projector’s control panel light or flash to
notify of problems, as described below.
An indicator is also used to notify you of the currently set power
mode. See “Power Cable Connections and Switching the Power
On/Off” on page E-22.STATUS indicator
Indicator status What you should do
Lit red
When the power is on (Lit green)
Standby (Lit...

E-58
Thermal Protector
When the temperature inside the projector becomes abnormally high, the STATUS indicator flashes red (0.5 seconds on/0.5
seconds off), the STANDBY indicator is a steady red, and at the same time the temperature protector operates and switches off
the power of the projector.
Should this happen, please take the following actions.
1. Switch off the power and disconnect the power plug from the wall outlet.
2. Check the following matters and take the required measures.
When the projector...

E-59
Troubleshooting
Check the following matters before requesting servicing.
•Is the power cord plugged into a power outlet?
•Is the lamp cover properly mounted?
•Is the projector’s temperature high? To protect the projector, the power can-
not be turned on when the projector’s temperature is abnormally high.
•Has the lamp reached the end of its service life?
•Is a connected input selected?
•Is the cable properly connected to the input terminal?
•When a computer is connected, are signals being output...

E-60
Cleaning
•Be certain to disconnect the power plug from the power outlet before cleaning.
•Do not spray or otherwise expose the projector, lens, or screen to volatile substances such as insecticides. Do not leave rubber
or vinyl products in contact with the projector for long periods. Doing so could cause them to undergo qualitative changes or the
coatings may peel, etc.
Cleaning a Soiled Projector Main Unit
•Wipe with a lint-free, soft, dry cloth.
When very dirty, wipe with a cloth that has been...