Plus Projector V 339 User Manual

E-20
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Lan-
guage Select] will be displayed. Follow the procedure described be-
low and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clock-
wise to focus it. See Page E-22.
1Press the SELECT (
) buttons of the Remote con-
trol and align the deep blue cursor with [English].
Cursor
2Press the ENTER button to set....

E-21
Power Cable Connections and Switching the Power On/Off
Finishing
1Switch off the power of the connected equip-
ment
2Switch off the power of the projector
Press the STANDBY button.
The [Power Off] display appears.
When the level gauge reaches maximum, the projection screen
will go off (in about 5 seconds) and the projector will enter the
power-off operation.
Note:
* The operation can be cancelled by pressing a button other than the
STANDBY button.
* One more press of the STANDBY button will switch...

E-22
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
2Adjust the projection image to the screen.
Check that the screen is set level and vertically.
Adjustment of the Projection Screen
Turn the zoom ring to adjust the screen size of the projection image.Adjust the image to match the desired screen size. When outside of the adjustment range, move the projector to the rear or
forward.
STANDBY...

E-23
Adjustment of the Projection Screen
STANDBY
STATUS
MENU
SOURCE
AUTO
ECL
O
Z
(
1)
(
2)
(
1)
DCM
Note:
When the projector has a rear installation is used, the orientation of the projection will need to be changed.
Please see “Vertical Flip / Horizontal Flip” on Page E-46.
Adjuster button
Making Adjustments with the Adjusters
Raising the projection image
While viewing the projection image, (1) press and hold
the front adjuster buttons located at the left and right and,
(2) raise the projector to align...

E-24
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-33 and the various items on
Pages E-40 to E-53.
Input Selection
STANDBY
FREEZE
MUTEECO AUTO
ASPECT
TIMER VOL KSTN ZOOMCANCEL QUICKMENU
ENTER
Q
1234
RGB
VIDEO
This operation selects the input signal to be projected.
Main unit operation: Press the SOURCE button.
(It will not function while the menu or...

E-25
General Operation
Selection of Aspect Ratio
Note:
When selection has been made for the “Real” setting of the personal computer signal (i.e., when the input signal and the projector display
resolution are high) and the “Zoom” setting of the video signal, pressing the SELECT (

) buttons on the remote control will permit
movement of the display position. Note that there will not be any movement when the menu or the quick menu is displayed.
This function selects horizontal and vertical picture...

E-26
STANDBY STATUS
MENU
DCM
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the input
image continues to advance even though the picture there is a still picture
condition.
A press of the FREEZE button changes the screen to a still picture. A
further press returns the screen to a moving picture.
General Operation
MUTEECO AUTO
ASPECT
TIMER VOL KSTN ZOOM234FREEZE1
Cancelling Video and Audio Temporarily
This function is used to cancel the video and audio at the...

E-27
Keystone Manual Adjustment
Use this to adjust for trapezoidal (keystone) distortion of the pro-
jected image. The projector has both an automatic and a manual key-
stone adjustment function. The manual adjustment will be described
here.
Adjustment Method
(1) Press the (
) buttons of the projector, or the (
) KSTN but-
tons of the remote control and set the left and right sides so that
they are parallel.
The keystone adjustment display appears when one of the buttons is
pressed.
General Operation...

E-28
General Operation
Enlargement of the Image and Video Movement
Note:
* Zoom and image movement functions are cancelled when the input is switched.
* The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected
so that they are not conspicuous.
* Movement of the screen will not be possible when the menu screen is being displayed.
This function digitally enlarges the personal computer image and video
image.
(1) Press the...

E-29
General Operation
Using the Presentation Timer
Note:
* The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will
still be operating at such times. Also, the timer will not be displayed unless a signal is being input.
* While the presentation timer is being displayed, screen movement will not be possible in the zoom mode.
[Timer settings display] The presentation is given while checking the timer displayed
on the screen....