Planar Pr6020 Projector User Manual

9English
Setting Up
Connecting the Projector
S-Video Output
Video OutputDVD Player, Settop Box, HDTV receiver
1.........................................................................\
.......................................VGA Cable2.............................................................Audio Input Cable (Optional Accessory)3.........................................................................\
........................................USB Cable...

0English

Setting Up

Powering On the Projector
1. Remove the lens cap. 
2.  Ensure that the power cord and signal cable are securely 
connected.  The Power LED will flash green.
3.  Turn on the lamp by pressing “Power” button on the control 
panel. And the Power LED will turn green.
4.  Turn on your source (computer, notebook, video player, 
etc.).  The projector will detect your source automatically 
within  “Management” menu; check that “Source Lock” has 
been set to “Off”.
	If you connect...

English

Setting Up

Warning Indicator
 When the “LAMP” indicator lights solid red, the projector 
will automatically shut itself down. Please contact your local 
reseller or service center.
  When the “TEMP” indicator lights solid red for about 60 
seconds, it indicates the projector has been overheated. The 
projector will automatically shut itself down.
  Under normal conditions, the projector can be switched on 
again after it has cooled down.  If the problem persists, you 
should...

2English

Setting Up

Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt Adjusting FootElevator FootElevator Button
The projector is equipped with elevator foot for adjusting the 
image height.
 To raise the image:
1.  Press the elevator button 
.
2.  Raise the image to the desired height angle 
, then release 
the button to lock the elevator foot into position.
3.  Use screw in feet 
 to fine-tune the display angle. 
 To lower the image:
1.  Press the elevator button.
2....

English

Setting Up

69.3(176.1cm)
115.6(293.5cm)
161.8(410.9cm)
208.0(528.3cm)
277.3(704.4cm)
38.1(96.8cm)
76.2(193.6cm)
127.1(322.7cm)
177.9(451.8cm)
228.7(580.9cm)
304.9(774.5cm)
4.9(1.5m)
39.4(12.0m)29.5(9.0m)23.0(7.0m)16.4(5.0m)9.8(3.0m)
34.7(88.1cm)
Width
HeightDiagonal
Hd

Focus Ring
Zoom Lever
Adjusting the Projector Zoom / Focus
You may turn the zoom lever to zoom in or out.  To focus the 
image, rotate the  focus ring until the image is clear. The pro-
jector  will  focus  at...

4English

User Controls

Using the Control Panel
PowerRefer to the “Power On/Off the Projector” section 
on pages 10-11.
Source Press “Source” to select an input signal.
MenuTurns the menu On or Off.
Four Direc-
tional Select 
Keys
Use        to navigate through the menus.
EnterConfirm your item selection.
Resync Automatically synchronizes the projector to the 
input source.
Control Panel & Remote Control
There are two ways for you to control the functions: Remote 
Control and Control Panel.
12
1
2 

English

User Controls

Using the Remote Control
PowerRefer to the “Power On/Off the Projector” section 
on pages 10-11.
Resync Automatically synchronizes the projector to the 
input source.
LaserAim the remote at the viewing screen, press and 
hold this button to activate the laser pointer.
SourcePress “Source” to select an input signal.
KeystoneAdjusts image distortion caused by tilting the 
projector (±16 degrees).
MuteMomentarily turns off the audio.
HideMomentarily turns off the picture....

English

User Controls

The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to Operate 
1. To open the OSD menu, press “Menu” on the Remote Control or 
Control Panel.
2. When OSD is displayed, use     keys to select any item in the 
main menu.  While making a selection on a particular page, press 
 key to enter sub menu.
3. Use      keys to select the desired...

English

User Controls

Menu Tree 

8English

User Controls

Language
 Language
Choose the multilingual OSD menu. Use the   or  key to select 
your preferred language. 
Press “Enter” to finalize the selection.