Planar Pr6020 Projector User Manual

							
9English
Setting Up
Connecting the Projector
S-Video Output
Video OutputDVD Player, Settop Box, HDTV receiver
1.........................................................................\
.......................................VGA Cable2.............................................................Audio Input Cable (Optional Accessory)3.........................................................................\
........................................USB Cable  4.........................................................................\
.................Composite Video Cable5.....................................................................S-Video Cable (Optional Accessory)6.........................................................Audio Output Cable (Optional Accessory)7.......................................SCART VGA/S-Video Adaptor (For European Only)8.....................................D-15 to RCA Adapter for YPbPr (Optional Accessory)
12
7
6
5
4
8
1
 To ensure the projector works well with your computer, 
please set the display mode of your graphic card less than 
or equal to 1600 x 1200 resolution. Make sure the timing of 
the display mode is compatible with the projector. Refer to 
the “Compatibility Modes” section on page 33.
3 
						

							
0English

Setting Up

Powering On the Projector
1. Remove the lens cap. 
2.  Ensure that the power cord and signal cable are securely 
connected.  The Power LED will flash green.
3.  Turn on the lamp by pressing “Power” button on the control 
panel. And the Power LED will turn green.
4.  Turn on your source (computer, notebook, video player, 
etc.).  The projector will detect your source automatically 
within  “Management” menu; check that “Source Lock” has 
been set to “Off”.
	If you connect multiple sources at the same time, use the 
“Source” button on the control panel or on remote control to 
switch.
Powering On/Off the Projector
	Turn on the projec-tor first and then the signal sources.
Lens Cap1
2Power 
						

							
English

Setting Up

Warning Indicator
 When the “LAMP” indicator lights solid red, the projector 
will automatically shut itself down. Please contact your local 
reseller or service center.
  When the “TEMP” indicator lights solid red for about 60 
seconds, it indicates the projector has been overheated. The 
projector will automatically shut itself down.
  Under normal conditions, the projector can be switched on 
again after it has cooled down.  If the problem persists, you 
should contact your local dealer or our service center.
 
 When the “TEMP” indicator lights solid red, it indicates the 
fan failed. Please contact your local dealer or our service 
center. 
Powering Off the Projector
1.   Press the “Power” button to turn off the projector lamp; you 
will see a message    
 
 displayed on the projector’s screen. Press the “Power” but-
ton again to confirm, otherwise the message will disappear 
after 5 seconds.
  Please note that if the 
 key is pressed instead,  the projector 
will enter the “Hide” mode and no image will be displayed.  
To exit the “Hide” mode, press the “Power” button again. 
 2.  The cooling fans continue to operate for about 20 seconds 
for cooling cycle and the Power LED will turn green. When 
the Power LED begins flashing, the projector has entered 
standby mode.
  If you wish to turn the projector back on, you must wait 
until the projector has completed the cooling cycle and has 
entered standby mode.  Once in standby mode, simply press 
“Power” button to restart the projector.
3.  Disconnect the power cord from the electrical outlet and the 
projector.
4.  Do not turn on the projector immediately following a power 
off procedure. 
						

							
2English

Setting Up

Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt Adjusting FootElevator FootElevator Button
The projector is equipped with elevator foot for adjusting the 
image height.
 To raise the image:
1.  Press the elevator button 
.
2.  Raise the image to the desired height angle 
, then release 
the button to lock the elevator foot into position.
3.  Use screw in feet 
 to fine-tune the display angle. 
 To lower the image:
1.  Press the elevator button.
2.  Lower the image, then release the button to lock the eleva
-
tor foot into position.
3.  Use screw in feet 
 to fine-tune the display angle.
1
23    
						

							
English

Setting Up

69.3(176.1cm)
115.6(293.5cm)
161.8(410.9cm)
208.0(528.3cm)
277.3(704.4cm)
38.1(96.8cm)
76.2(193.6cm)
127.1(322.7cm)
177.9(451.8cm)
228.7(580.9cm)
304.9(774.5cm)
4.9(1.5m)
39.4(12.0m)29.5(9.0m)23.0(7.0m)16.4(5.0m)9.8(3.0m)
34.7(88.1cm)
Width
HeightDiagonal
Hd

Focus Ring
Zoom Lever
Adjusting the Projector Zoom / Focus
You may turn the zoom lever to zoom in or out.  To focus the 
image, rotate the  focus ring until the image is clear. The pro-
jector  will  focus  at  distances  from  4.9  to  39.4  feet  (1.5  to  12.0 
meters) with mechanical travel. 
Adjusting Projection Image Size
This graph is for user’s reference only.
Screen(Diagonal)
Max.38.1”(96.8cm)76.2”(193.6cm)127.1”(322.7cm)177.9”(451.8cm)228.7”(580.9cm)304.9”(774.5cm)Min.34.7”(88.1cm)69.3”(176.1cm)115.6”(293.5cm)161.8”(410.9cm)208.0”(528.3cm)277.3”(704.4cm)
Screen 
Size
Max.(WxH)30.5”x 22.9”77.4 x 58.1cm61.0” x 45.7”154.9 x 116.2cm101.7” x 76.3”258.2 x 193.6cm142.3” x 106.7”361.4 x 271.1cm183.0” x 137.2”464.7 x 348.5cm243.9” x 182.9”619.6 x 464.7cmMin.(WxH)27.8” x 20.8”70.5 x 52.9cm55.4” x 41.6”140.9 x 105.7cm92.5” x69.4”234.8 x 176.1cm129.4” x 97.1”328.7 x 246.5cm166.4” x 124.8”422.6 x 317.0cm221.8” x 166.4”563.5 x 422.6cm
HdMax.3.4” (8.7cm)6.9” (17.4cm)11.4” (29.0cm)16.0” (40.7cm)20.6” (52.3cm)27.4” (69.7cm)Min.3.1” (7.9cm)6.2” (15.9cm)10.4” (26.4cm)14.6” (37.0cm)18.7” (47.6cm)25.0” (63.4cm)
Distance4.9’ (1.5m)9.8’ (3.0m)16.4’ (5.0m)22.3’ (7.0m)29.5’ (9.0m)39.4’ (12.0m)                                   
						

							
4English

User Controls

Using the Control Panel
PowerRefer to the “Power On/Off the Projector” section 
on pages 10-11.
Source Press “Source” to select an input signal.
MenuTurns the menu On or Off.
Four Direc-
tional Select 
Keys
Use        to navigate through the menus.
EnterConfirm your item selection.
Resync Automatically synchronizes the projector to the 
input source.
Control Panel & Remote Control
There are two ways for you to control the functions: Remote 
Control and Control Panel.
12
1
2 
						

							
English

User Controls

Using the Remote Control
PowerRefer to the “Power On/Off the Projector” section 
on pages 10-11.
Resync Automatically synchronizes the projector to the 
input source.
LaserAim the remote at the viewing screen, press and 
hold this button to activate the laser pointer.
SourcePress “Source” to select an input signal.
KeystoneAdjusts image distortion caused by tilting the 
projector (±16 degrees).
MuteMomentarily turns off the audio.
HideMomentarily turns off the picture. To exit the 
“Hide” feature, press “Hide” button again.
FreezePress “Freeze” to pause the screen image.
Page UpUse this button to page up.
Page DownUse this button to page down.
Four Direc-
tional Select 
Keys
Use        to navigate through the menus.
MenuDisplay or exits the on-screen display menus for 
projector.
EnterConfirm your item selection. 
						

							
English

User Controls

The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to Operate 
1. To open the OSD menu, press “Menu” on the Remote Control or 
Control Panel.
2. When OSD is displayed, use     keys to select any item in the 
main menu.  While making a selection on a particular page, press 
 key to enter sub menu.
3. Use      keys to select the desired item and adjust the settings 
by     key.  
4. Select the next item to be adjusted in the sub menu and adjust as 
described above.   
5. Press “Menu” to confirm, and the screen will return to the main 
menu.
6. To exit, press “Menu” again.  The OSD menu will close and the 
projector will automatically save the new settings.
On Screen Display Menus
Main Menu
Sub MenuSetting 
						

							
English

User Controls

Menu Tree 
						

							
8English

User Controls

Language
 Language
Choose the multilingual OSD menu. Use the   or  key to select 
your preferred language. 
Press “Enter” to finalize the selection.