Home > Planar > Projector > Planar Pr5022 Projector User Manual

Planar Pr5022 Projector User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Planar Pr5022 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 34 Planar manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    DLP® Projector – User’s Manual 
    Status Menu  
    Press the Menu button to open the Main menu. Press the cursor  button to move to the Status 
    menu. Press the cursor  button to move up and down in the Status menu. 
     
    Item Description Default 
    Video  
    Information 
    Displays the resolution and refresh rate for RGB/DVI mode. 
    Displays the color standard for video mode. 
    Active Source Displays the active source. 
    Software 
    Version 
    Displays information about the software version. 
    Lamp Hours Shows the number of hours lamp has been in use for Eco and 
    Normal  modes. 
    These 
    items are 
    display 
    only. 
    Lamp Mode Press the cursor  button to choose the lamp mode.  
    Range: Eco and Normal. 
    Eco mode uses less power and extends lamp life, but decreases 
    lamp brightness.  
    Normal mode uses more power and reduces lamp life, but in-
    creases lamp brightness. 
    Normal 
    Lamp Hour  
    Reset 
    After replacing the lamp, this item should be reset. Refer to “Replacing 
    the Projection Lamp” on page 34.  
    — 
    – 33 –  
    						
    							
     
    – 34 – 
    Maintenance and Security 
    Replacing the Projection Lamp 
    The projection lamp should be replaced when it burns out. It should only be replaced with a certified 
    replacement part, which you can order from your local dealer.  
    Important: 
    1. The lamp contains a certain amount of mercury and should be disposed of according to local ordi-
    nance regulations. 
    2. Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life. 
     
    Warning: 
    Be sure to turn off and unplug the projector at least an hour before replacing the lamp. Failure to do so 
    could result in a severe burn. 
     
    Note: 
    Safety glasses should be worn when replacing the lamp while the projector is ceiling mounted. 
     
     
    1.  Loosen the two cap-
    tive screws on the 
    lamp compartment 
    cover (A). 
     
      
    						
    							
    DLP® Projector – User’s Manual 
    2.  Open the lamp com-
    partment cover (B). 
    B
     
    3.  Remove the two 
    screws from the lamp 
    module (C). 
    4.  Lift the module handle 
    up (D).  
    – 35 –  
    						
    							
    DLP® Projector – User’s Manual 
    5.  Pull firmly on the 
    module handle to re-
    move the lamp module 
    (D) 
     
    D
     
    6.  Reverse steps 1 to 5 
    to install the new lamp 
    module. 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    – 36 –  
    						
    							
    DLP® Projector – User’s Manual 
    Resetting the Lamp 
    After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 
    1.  Press the Menu button to open 
    the Main menu. 
    2.  Press the cursor  button to 
    move to the Status menu. 
    3.  Press the cursor  button to 
    move down to Lamp Hour Reset.
    4.  Press the cursor  or Enter 
    button.  
    A message screen appears. 
    5.  Press the cursor buttons in this 
    order: ; ; ; . 
    The Status menu appears again 
    showing the Lamp Hours reset to 
    zero. 
    Cleaning the Projector 
    Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
    Warning: 
    1. Be sure to turn off and unplug the projector at least an hour before cleaning. Failure to do so could 
    result in a severe burn. 
    2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on 
    the projector.  
    3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated 
    room for several hours before using. 
    4. If a lot of water gets into the projector interior when cleaning, have the projector serviced. 
    Cleaning the Lens 
    You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the pro-
    jector lens. 
    – 37 –  
    						
    							
    DLP® Projector – User’s Manual 
    1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to 
    the lens.) 
    2. Lightly wipe the lens in a circular motion. 
    Caution: 
    1. Do not use abrasive cleaners or solvents. 
    2. To prevent discoloration or fading, avoid getting cleaner on the projector case. 
    Cleaning the Case 
    Refer to the following to clean the projector case. 
    1. Wipe off dust with a clean dampened cloth. 
    2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and 
    then wipe the case. 
    3. Rinse all detergent from the cloth and wipe the projector again. 
    Caution: 
    To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners. 
    Using the Kensington® Lock 
    If you are concerned about security, attach the projector to a permanent object with the Kensington 
    slot and a security cable.  
     
    Note: 
    Contact your vendor for details on purchasing a suitable Kensington security cable.  
    The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, 
    contact: Kensington, 2853 Campus Drive, San Mateo, CA94403, U.S.A. Tel: 800-535-4242, 
    http://www.Kensington.com. 
     
    – 38 –  
    						
    							
     
    – 39 – 
    Troubleshooting 
    Common problems and solutions 
    These guidelines provide tips to deal with problems you may encounter while using the projector. If 
    the problem remains unsolved, contact your dealer for assistance. 
    Often after time spent troubleshooting, the problem is traced to something as simple as a loose con-
    nection. Check the following before proceeding to the problem-specific solutions. 
    • Use some other electrical device to confirm that the electrical outlet is working. 
    • Ensure the projector is turned on. 
    • Ensure all connections are securely attached.  
    • Ensure the attached device is turned on. 
    • Ensure a connected PC is not in suspend mode. 
    • Ensure a connected notebook computer is configured for an external display. (This is usu-
    ally done by pressing an Fn-key combination on the notebook.) 
    Tips for Troubleshooting 
    In each problem-specific section, try the steps in the order suggested. This may help you to solve the 
    problem more quickly. 
    Try to pin point the problem and thus avoid replacing non-defective parts.  
    For example, if you replace batteries and the problem remains, put the original batteries back and go 
    to the next step.  
    Keep a record of the steps you take when troubleshooting: The information may be useful when call-
    ing for technical support or for passing on to service personnel. 
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							
    DLP® Projector – User’s Manual 
    LED Error Messages 
    Error code message Power LED/flashes Ready LED/flashes 
    Lamp usage task created error 2 1 
    Environment usage task created error 2 2 
    Thermal break status error 3 0 
    T1 temperature over temperature 3 1 
    T1 sensor status fail 4 1 
    Lamp lit error 5 1 
    Ballast SCI error 5 2 
    Ballast UART error 5 3 
    Fan1 error (Lamp) 6 1 
    Fan2 error (Ballast) 6 2 
    Fan3 error (Burner) 6 3 
    Fan4 error (Power) 6 4 
    Lamp door sensor detect high 7 0 
    DMD error 8 0 
    Color wheel error 9 0 
     
    Image Problems 
    Problem: No image appears on the screen 
    1. Verify the settings on your notebook or desktop PC. 
    2. Turn off all equipment and power up again in the correct order. 
    Problem: The image is blurred  
    1. Adjust the Focus on the projector. 
    2. Press the Auto button on the remote control or projector. 
    3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range. 
    4. Check that the projector lens is clean. 
    Problem: The image is wider at the top or bottom (trapezoid effect)  
    1. Position the projector so it is as perpendicular to the screen as possible.  
    2. Use the Keystone button on the remote control or projector to correct the problem. 
    Problem: The image is reversed or upside down 
    Check the Projection setting on the Utility menu of the OSD. 
    Problem: The image is streaked  
    1. Set the Frequency and Tracking settings on the Utility menu of the OSD to the default 
    settings. 
    – 40 –  
    						
    							
    DLP® Projector – User’s Manual 
    2. To ensure the problem is not caused by a connected PC’s video card, connect to another 
    computer.  
    Problem: The image is flat with no contrast  
    Adjust the Contrast setting on the Main menu of the OSD. 
    Problem: The color of the projected image does not match the source imag\
    e. 
    Adjust the Color Temperature and Gamma settings on the Main menu of the OSD. 
    Lamp Problems 
    Problem: There is no light from the projector  
    1. Check that the power cable is securely connected. 
    2. Ensure the power source is good by testing with another electrical device. 
    3. Restart the projector in the correct order and check that the Power LED is green. 
    4. If you have replaced the lamp recently, try resetting the lamp connections.  
    5. Replace the lamp module. 
    6. Put the old lamp back in the projector and have the projector serviced. 
    Problem: The lamp goes off 
    1. Power surges can cause the lamp to turn off. Press the power button twice to turn off the 
    projector. When the Ready LED is on, press the power button. 
    2. Replace the lamp module. 
    3. Put the old lamp back in the projector and have the projector serviced. 
    Remote Control Problems 
    Problem: The projector does not respond to the remote control  
    1. Direct the remote control towards remote sensor on the projector.  
    2. Ensure the path between remote and sensor is not obstructed. 
    3. Turn off any fluorescent lights in the room. 
    4. Check the battery polarity. 
    5. Replace the batteries. 
    6. Turn off other Infrared-enabled devices in the vicinity. 
    7. Have the remote control serviced. 
    Audio Problems 
    Problem: There is no sound 
    1. Adjust the volume on the remote control.  
    2. Adjust the volume of the audio source. 
    3. Check the audio cable connection. 
    4. Test the source audio output with other speakers. 
    5. Have the projector serviced. 
    Problem: The sound is distorted  
    1. Check the audio cable connection. 
    2. Test the source audio output with other speakers. 
    3. Have the projector serviced. 
     
    – 41 –  
    						
    							
     
    – 42 – 
    Specifications 
    Input/output connectors 
    DVI-D Data in 
    RGB HD-15 
    Data out RGB HD-15 
    Composite video (RCAx1) Video 
    S-video 
    Stereo RCAx2 (L+R) Audio in 
    Stereo Mini-jack 
    Audio out Stereo Mini-jack 
    RS-232 Control 
    USB 
    Security Kensington lock 
     
     
     
     
     
     
     
     
     
      
    						
    All Planar manuals Comments (0)

    Related Manuals for Planar Pr5022 Projector User Manual