Planar Pr5022 Projector User Manual

							
DLP® Projector – User’s Manual 
Starting and Shutting down the Projector 
1.  Slide the lens cover. 
2.  Connect the power cord to the projector 
[A]  Connect the other end to a wall out-
let.  Switch [B] from on (O) to off ( — )   
3.  The POWER and READY LEDs on the 
projector turn on.                                         
Turn on the connected devices.  
4.  Ensure the Ready LED is on a steady 
(not flashing) orange and then press the 
Power button to turn on the projector.  
 
The projector splash screen displays and 
connected devices are detected. 
If the connected device is a PC, press the 
appropriate keys on the computer key-
board to switch the display output to the 
projector. (Check the user manual of the 
PC to determine the appropriate Fn key 
combination to change display output.) 
 
See “Setting an Access Password (Secu-
rity Lock)” on page 15 if Security Lock is 
enabled. 
5.  If more than one input device is con-
nected, press the Source button 
repeatedly to switch among devices. 
(DVD and HDTV are supported through 
the VGA connector.)  
6.  To turn off the projector, press the Power 
button. The projector prepares for shut-
down and a “Wait a moment please…” 
message appears.  
– 13 –  
						

							
DLP® Projector – User’s Manual 
7.  When the “Power Off?/Press Power 
again” message appears, press the 
Power button. The projector turns off. 
 
8.  Turn off the main Power switch when the 
Ready LED stops flashing. 
 
 
Caution: 
Do not unplug the power cord until the Ready LED stops flashing, indicating the projector has cooled 
down. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
– 14 –  
						

							
DLP® Projector – User’s Manual 
Setting an Access Password (Security Lock) 
You can use the cursor (arrow) buttons to set a password and prevent unauthorized use of the pro-
jector. When enabled, the password must be entered after you power on the projector. (See 
“Navigating the OSD” on page 20 and “Setting the OSD Language” on page 21 for help on using 
OSD menus.) 
Important: 
Keep the password in a safe place. Without the password, you will not be able to use the projector. 
If you lose the password, contact your reseller for information on clearing the password. 
 
1.  Press the Menu button to open the 
OSD menu. 
2.  Press the cursor  button to move 
to the Setup menu. 
3.  Press the cursor  button to select 
Advance Feature and press Enter or 
.  
4.  Press the cursor  button to select 
Security Lock. 
5.  Press the cursor Enter or  button to 
select Enable. (White text is selected.)
A password dialog box automatically 
appears. 
 
6
 
You can only use the following four 
cursor buttons:     
in the password fields. You can use 
any combination including the same 
arrow five times, but not less than five.
Press the cursor buttons in any order 
to set the password. When you 
confirm the password, OK appears. 
 
– 15 –  
						

							
DLP® Projector – User’s Manual 
 Every time you start the projector, a 
password dialog box appears. 
 
Enter the password in the order you 
set it at step 6. (Press the Menu 
button to cancel if you enter the wrong 
password.)  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
– 16 –  
						

							
DLP® Projector – User’s Manual 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
• Position the projector so that it is perpendicular to the screen. 
• Be sure cables are not in the way or can cause the projector to be knocked over. 
 
 
 
1.  To raise the level of the projector, lift the projector [A] and press the height-
adjuster button [B].  
The height adjuster drops down [C].  
2.  To lower the level of the projector , press the height-adjuster button and 
push down on the top of the projector. 
3.  To adjust the angle of the picture, turn the tilt adjuster  [D] right or left until 
desired angle has been achieved. 
 
 
 
– 17 –  
						

							
DLP® Projector – User’s Manual 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom 
control (on the projector 
only) to resize the pro-
jected image and 
screen size. B 
2.  Use the Image-focus 
control (on the projector 
only) to sharpen the 
projected image A. 
 
3.  Press the Keystone 
button on the remote 
control. 
The keystone control 
appears on the display.  
 
4.  Use the Keystone but-
ton to correct image 
distortion.  
Adjusting the Volume 
1.  Press the Volume +/- 
button on the remote 
control.  
The volume control ap-
pears on the display.  
 
2.  Use the Volume +/- 
button to adjust the 
level. 
 
– 18 –  
						

							
DLP® Projector – User’s Manual 
3.  Press the Mute button 
to turn off the volume. 
(For remote only)  
– 19 –  
						

							
DLP® Projector – User’s Manual 
On-Screen Display (OSD) Menu Settings 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illustration shows the corresponding buttons on the re-
mote control and on the projector. 
 
                
1. To open the OSD, press the Menu button.  
2. There are six menus. Press the cursor  but-
ton to move through the menus.  
3. Press the cursor  button to move up and 
down in a menu.  
4. Press  to change values for settings, and 
then press Enter or  to confirm the new set-
ting. 
5. Press Menu to close the OSD or leave a sub-
menu. 
 
Note: 
Depending on the video source not all items in the OSD are available. For example, the Horizon-
tal/Vertical Position items in the Setup menu can only be modified when connected to a PC. Items 
that are not available cannot be accessed and are grayed out.  
– 20 –  
						

							
DLP® Projector – User’s Manual 
Setting the OSD Language 
You may want to reference the OSD on your projector while reading this section. Set the OSD lan-
guage to your preference before continuing. (The default language is English.) 
1. Press the Menu button. The Main menu appears. 
 
2. Press the cursor  button until Tool is highlighted.  
 
3. Press the cursor  button until Tool is highlighted.  
4. Press the  button until your language is displayed. 
5. Press the Menu button twice to close the OSD. 
 
 
 
 
 
 
– 21 –  
						

							
DLP® Projector – User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting.  
 
– 22 –