Planar Pr5022 Projector User Manual

DLP® Projector – User’s Manual 
Status Menu  
Press the Menu button to open the Main menu. Press the cursor  button to move to the Status 
menu. Press the cursor  button to move up and down in the Status menu. 
 
Item Description Default 
Video  
Information 
Displays the resolution and refresh rate for RGB/DVI mode. 
Displays the color standard for video mode. 
Active Source Displays the active source. 
Software 
Version 
Displays information about the software version. 
Lamp Hours Shows the number of...

 
– 34 – 
Maintenance and Security 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be replaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
1. The lamp contains a certain amount of mercury and should be disposed of according to local ordi-
nance regulations. 
2. Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life. 
 
Warning: 
Be sure to turn off and unplug the...

DLP® Projector – User’s Manual 
2.  Open the lamp com-
partment cover (B). 
B
 
3.  Remove the two 
screws from the lamp 
module (C). 
4.  Lift the module handle 
up (D).  
– 35 –  

DLP® Projector – User’s Manual 
5.  Pull firmly on the 
module handle to re-
move the lamp module 
(D) 
 
D
 
6.  Reverse steps 1 to 5 
to install the new lamp 
module. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
– 36 –  

DLP® Projector – User’s Manual 
Resetting the Lamp 
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 
1.  Press the Menu button to open 
the Main menu. 
2.  Press the cursor  button to 
move to the Status menu. 
3.  Press the cursor  button to 
move down to Lamp Hour Reset.
4.  Press the cursor  or Enter 
button.  
A message screen appears. 
5.  Press the cursor buttons in this 
order: ; ; ; . 
The Status menu appears again 
showing the Lamp Hours reset...

DLP® Projector – User’s Manual 
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to 
the lens.) 
2. Lightly wipe the lens in a circular motion. 
Caution: 
1. Do not use abrasive cleaners or solvents. 
2. To prevent discoloration or fading, avoid getting cleaner on the projector case. 
Cleaning the Case 
Refer to the following to clean the projector case. 
1. Wipe off dust with a clean dampened cloth. 
2. Moisten the cloth with warm water and mild detergent...

 
– 39 – 
Troubleshooting 
Common problems and solutions 
These guidelines provide tips to deal with problems you may encounter while using the projector. If 
the problem remains unsolved, contact your dealer for assistance. 
Often after time spent troubleshooting, the problem is traced to something as simple as a loose con-
nection. Check the following before proceeding to the problem-specific solutions. 
• Use some other electrical device to confirm that the electrical outlet is working. 
• Ensure the...

DLP® Projector – User’s Manual 
LED Error Messages 
Error code message Power LED/flashes Ready LED/flashes 
Lamp usage task created error 2 1 
Environment usage task created error 2 2 
Thermal break status error 3 0 
T1 temperature over temperature 3 1 
T1 sensor status fail 4 1 
Lamp lit error 5 1 
Ballast SCI error 5 2 
Ballast UART error 5 3 
Fan1 error (Lamp) 6 1 
Fan2 error (Ballast) 6 2 
Fan3 error (Burner) 6 3 
Fan4 error (Power) 6 4 
Lamp door sensor detect high 7 0 
DMD error 8 0 
Color wheel...

DLP® Projector – User’s Manual 
2. To ensure the problem is not caused by a connected PC’s video card, connect to another 
computer.  
Problem: The image is flat with no contrast  
Adjust the Contrast setting on the Main menu of the OSD. 
Problem: The color of the projected image does not match the source imag\
e. 
Adjust the Color Temperature and Gamma settings on the Main menu of the OSD. 
Lamp Problems 
Problem: There is no light from the projector  
1. Check that the power cable is securely...

 
– 42 – 
Specifications 
Input/output connectors 
DVI-D Data in 
RGB HD-15 
Data out RGB HD-15 
Composite video (RCAx1) Video 
S-video 
Stereo RCAx2 (L+R) Audio in 
Stereo Mini-jack 
Audio out Stereo Mini-jack 
RS-232 Control 
USB 
Security Kensington lock