Planar Pr3020 Projector Specifcations Manual

							User’s Manual 
– 14 – 
7.  
 
 
8.  
 
When the “Power Off?/Press Power again” 
message appears, press the Power button. 
The projector turns off. 
Turn off the main Power switch when the 
Ready LED stops flashing. 
.  
 
 
Caution: 
Do not unplug the power cord until the Ready LED stops flashing, indicating the projector has 
cooled down.  
						

							DLP® Projector – User’s Manual 
– 15 – 
Setting an Access Password (Security Lock) 
You can use the cursor (arrow) buttons to set a password and prevent unauthorized use of the 
projector. When enabled, the password must be entered after you power on the projector. (See 
“Navigating the OSD” on page 32 and “Setting the OSD Language” on page 32 for help on using 
OSD menus.) 
Important: 
Keep the password in a safe place. Without the password, you will not be able to use the projector. 
If you lose the password, contact your reseller for information on clearing the password. 
 
1.  Press the Menu button to open the OSD 
menu. 
2.  Press the cursor  button to move to the 
Setup menu. 
3.  Press the cursor  button to select 
Advance Feature and press Enter or 
.  
4.  Press the cursor  button to select 
Security Lock. 
5.  Press the cursor Enter or  button to 
select Enable. (White text is selected.) 
A password dialog box automatically 
appears. 
 
6. You can only use the following four 
cursor buttons: 
    
in the password fields. You can use any 
combination including the same arrow five 
times, but not less than six. 
Press the cursor buttons in any order to set 
the password. When you confirm the 
password, OK appears. 
 
 Every time you start the projector, a 
password dialog box appears. 
 
Enter the password in the order you set it 
at step 6. (Press the Menu button to cancel 
if you enter the wrong password.) 
  
						

							User’s Manual 
– 16 – 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
• Position the projector so that it is perpendicular to the screen. 
• Be sure cables are not in the way or can cause the projector to be knocked over. 
 
 
 
6.  To raise the level of the projector, lift the projector [A] and press the height-adjuster 
button [B].  
The height adjuster drops down [C].  
7.  To lower the level of the projector , press the height-adjuster button and push down 
on the top of the projector. 
8.  To adjust the angle of the picture, turn the tilt adjuster  [D] right or left until desired 
angle has been achieved. 
  
						

							DLP® Projector – User’s Manual 
– 17 – 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom 
control (on the projector 
only) to resize the 
projected image and 
screen size.
 
B 
2.  Use the Image-focus 
control (on the projector 
only) to sharpen the 
projected image 
A. 
 
3.  Press the Keystone button 
on the remote control. 
The keystone control 
appears on the display.  
 
4.  Use the Keystone button 
to correct image 
distortion. 
 
Adjusting the Volume 
1.  Press the Volume +/- 
button on the remote 
control.  
The volume control 
appears on the display.  
 
2.  Use the Volume +/- 
button to adjust the level. 
  
						

							User’s Manual 
– 18 – 
3.  Press the Mute button to 
turn off the volume. (For 
remote only) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							DLP® Projector – User’s Manual 
– 19 – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illustration shows the corresponding buttons on the 
remote control and on the projector. 


                
1.  To open the OSD, press the Menu button.  
2.  There are six menus. Press the cursor 
 
button to move through the menus.  
3. Press the cursor 
 button to move up and 
down in a menu.  
4. Press 
 to change values for settings, and 
then press Enter or 
 to confirm the new 
setting. 
5. Press Menu to close the OSD or leave a 
submenu. 
 
Note: 
Depending on the video source not all items in the OSD are available. For example, the 
Horizontal/Vertical Position items in the Setup menu can only be modified when connected to a 
PC. Items that are not available cannot be accessed and are grayed out.   
						

							User’s Manual 
– 20 – 
Setting the OSD Language 
You may want to reference the OSD on your projector while reading this section. Set the OSD 
language to your preference before continuing. (The default language is English.) 
1. Press the Menu button. The Main menu appears. 
 
2. Press the cursor  button until Tool is highlighted.  
 
3. Press the cursor  button until Tool is highlighted.  
4. Press the 
 button until your language is displayed. 
5. Press the Menu button twice to close the OSD. 
 
 
 
 
 
 
 
  
						

							DLP® Projector – User’s Manual 
– 21 – 
Setting the OSD Language 
Use the following illustration to quickly find a setting or determine the range for a setting.  
  
						

							User’s Manual 
– 22 – 
Main Menu  
Press the Menu button to open the OSD menu. Press the cursor  button to move to the Main 
menu. Press the cursor 
 button to move up and down in the Main menu. Press  to change 
values for settings, and then press Enter or 
 to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT 
Brightness  Press the cursor  button to adjust the brightness. (Range: 0 – 100)  50 
Contrast  Press the cursor  button to adjust the contrast. (Range: 0 – 100)  50 
Sharpness  Press the cursor  button to adjust the display sharpness (Range: 1-5)  3 
Color  
Temperature Press the cursor  button to adjust the color temperature.  
(Range: Cool/Normal/Warm) Normal 
Color  
Saturation Press the cursor  button to adjust the video saturation. (Range: 0 – 100)  50 
Color Tint  Press the cursor  button to adjust the video tint/hue. (Range: 0 – 100) 50 
Gamma  Press the cursor  button to adjust the gamma correction of the display.  
Input Gamma  
PC 2.2 
MAC 1.8 
Video 2.4 
Chart 2.2 
B&W 2.4 
  
Data source:  
PC 
 
Video source: 
Video 
 
Color Space  Press the cursor  button to adjust the color space.  
(Range: Auto – RGB – YPbPr- YCbCr) Auto 
Reset Resets all Main settings to default values  —  
						

							DLP® Projector – User’s Manual 
– 23 – 
Main Menu Functions Available for Connected Source 
Function RGB DVI Component VideoComposite Video S-video 
Brightness x x  x  x  x 
Contrast x x  x  x  x 
Sharpness x x  x  x  x 
Color Temp x x  x  x  x 
Color Saturation    x  x  x 
Color Tint    x  x  x 
Gamma x x  x  x  x 
Color Space x x  x  x  x 
Reset x x  x  x  x 
x = available to video source