Planar Pd7130 Projector User Manual

							Appendix
33
Appendix 
						

							34
Appendix
Maintenance
Cleaning the projector
„Unplug the power cord before cleaning the projector.
„Avoid using benzene or thinners, as these can damage the finish on the cabinet and operation panel.
„Do not use volatile agents, such as insecticides, on the projector.
„Do not leave rubber or plastic objects in contact with the projector for long periods, as they may damage 
the finish of the projector.
„Wipe off dirt gently with a soft flannel cloth.
„For hard-to-remove dirt, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then 
wipe the projector.
Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test 
on a small, inconspicuous area on the projector before use.
Cleaning the lens
„Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning 
the lens. Do not use any liquid cleaning agents, as they may wear off the coating film on the surface of the 
lens.
„The surface of the lens is easily damaged, do not to scrape or hit the lens.
SOURCE
M
ENU ENTER
SOURCE
M
ENU ENTER
SOUR
CE
ME
NU ENTE
R 
						

							Appendix
35
About the Lamp
The projector lamp has a life span of approximately 2000 hours. Maintain proper ventilation to 
keep the lamp operating throughout its lifetime. Do not subject the projector to unnecessary 
vibrations to ensure that the lamp does not break.
„It is recommended that the lamp (sold separately) be replaced after approximately 2,000 cumulative hours 
of use or when you notice a significant deterioration in the picture and color quality. The number of hours 
the lamp has been used can be checked with “Lamp Timer” in the “Options” menu on the menu screen.
„For lamp replacement, please consult your nearest authorized service center or dealer.
„The actual lamp service life may be less than 2000 hours depending on the environment in which the 
projector is used.
Caution Concer ning the Lamp
„This projector uses a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure is 
caused by excessive shock, improper cooling, surface scratches or deterioration of the lamp due to usage. 
The period of time up to failure largely varies depending on the individual lamp and/or the condition and 
the frequency of use. It is important to note that failure can often result in the bulb cracking.
„When the lamp replacement indicator and on-screen display icon are illuminated or are flashing, it is 
recommended that the lamp be replaced immediately, even if the lamp appears to be operating normally.
„If the lamp breaks, glass particles may spread inside the lamp cage or gas contained in the lamp may be 
vented into the room from the exhaust vent. As the gas in this lamp contains mercury, ventilate the room 
well if the lamp breaks and avoid exposure. In case of exposure to the gas, consult a doctor as soon as 
possible.
„If the lamp breaks, there is also a possibility that glass particles may spread inside the projector.
If this happens, it is recommended you contact your nearest authorized dealer to remove the damaged 
lamp and assure safe operation.
Replacing the Lamp
CAUTION!  Do not remove the lamp unit immediately after operation of the projector. The 
lamp will be hot and touching it may cause injury. Wait at least one hour after the power cord 
is disconnected to allow the surface of the lamp unit to fully cool before removing.
Temperature LED (Temperature Overheat Alarm)
The temperature LED acts as an alarm to alert you when the 
projector lamp becomes too hot. 
If the LED illuminates during operation, the lamp shuts off and 
the cooling fan continues to run for approximately two minutes. 
You should ensure that the airflow around the projector is 
sufficient and that the cooling fan intake vent is not clogged to 
ensure that the projector has proper ventilation. 
Please pay attention that the cooling fan and intake vent are 
not clogged. Please see “Projector (Front and Top View)” on 
page 3 for their location.
In addition to the LED illuminating, the following warning is also projected:Temperature LED
SOURCE
MENU ENTER
Temperature Overheat! 
						

							36
Appendix
Removing and Replacing the Lamp
Follow these instructions to replace the lamp.
•  
Remove the lamp unit by the handle. Do not to touch the glass surface of the lamp unit or the inside of the 
projector.
•  To avoid injuring yourself and damaging the lamp, carefully follow the steps below.
•  Only loosen the screws for the lamp unit cover and lamp unit. 
(Only the silver screws are loosened).
1. If the projector is running, press   on the projector or   on the remote control to 
turn off the power. Wait until the cooling fan stops.
 Warning!
Do not remove the lamp unit from the projector immediately after use. The lamp will be very hot and may 
cause injury.
2. Disconnect the power cord and wait at least an hour for the lamp to cool.
3. Remove the lamp unit cover.
•  
Loosen the screw that secures the lamp unit cover. Now open the cover in the direction of the arrow.
ON
23
5 4 1
POWER
ENTER
MENU EXITUSER MEMORY
SOURCEOFF
MENU
SOURCE
ENTER
S
O
U
R
C
E
M
E
N
U E
N
T
E
R
SOURGE
MENU ENTER
 M4* 10 screws 
						

							Appendix
37
4. Remove the lamp unit.
•  
Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction 
of the arrow.
   
5. Insert the new lamp unit.
•  
Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.
•  Attach the lamp unit cover.
•  Close the lamp unit cover in the direction of the arrow (to the close mark) on the side of the projector. 
•  Tighten the cover screw.
 Info
•  
If the lamp unit and lamp cover are not correctly installed, the power will not turn on.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1. Connect the power cord.
•  
Plug the power cord into the AC socket of the projector.
2. Reset the lamp timer.
•  
In the OSD Main menu, press S or T button to select Option menu.
•  Press W or X button to select Lamp Timer Reset.
•  Press   to confirm, and “LAMP 0H“is displayed. The lamp timer is reset.
 Info
Only reset the lamp timer when replacing the lamp. If you reset the lamp timer and continue to use the same 
lamp, this may cause the lamp to become damaged or explode.
SOURGE
MENU ENTERSOURGE
MENU EN
TE
R
SOURGE
MENU ENTER
ENTER 
						

							38
Appendix
Connecting Pin Assignments
DVI-D port: 25 pin connector
•  VI Digital INPUT
RS-232C Port: 9-pin D-sub Female connector of the DIN-D-sub RS-232Cvt cable 
pin connector
   
Pin No. Signal Pin No. Signal
1 T.M.D.S data 2- 16 Hot plug detection
2 T.M.D.S data 2+ 17 T.M.D.S data 0–
3 T.M.D.S data 2 shield 18 T.M.D.S data 0+
4 Not connected 19 T.M.D.S data 0 shield
5 Not connected 20 Not connected
6 DDC clock 21 Not connected
7 DDC data 22 T.M.D.S clock shield
8 Not connected 23 T.M.D.S clock+
9 T.M.D.S data 1– 24 T.M.D.S clock–
10 T.M.D.S data 1+ C1 Ground
11 T.M.D.S data 1 shield
12 Not connected
13 Not connected
14 +5V power from 
graphic card.
15 Ground
Pin No. Signal Name I/O Reference
1Not connected
2 SD Send Data Input Connected to internal circuit
3 RD Receive Data Output Connected to internal circuit
4 Not connected
5 SD Signal Ground Connected to internal circuit
6 Not connected
7 Not connected
8 Not connected
9 Not connected
168  7      ~      2 1           ~              
 ~    24
2318
17
9 C1
4321
9
876
5 
						

							Appendix
39
Computer Compatibility Chart
Computer
•  Multiple signal support
Horizontal Frequency: 25–75 kHz, Vertical Frequency: 50–85 Hz, Pixel Clock: 25–108 MHz
•  Compatible with sync on green and composite sync signals
•  XGA compatible with advanced intelligent compression
The following is a list of modes that conform to VESA. However, this projector supports 
other signals that are not VESA standards.
PC/
MAC/
WSResolutionHorizontal 
Frequency 
(kHz)Ve r t i c a l  
Frequency 
(kHz)VESA 
StandardDVI 
Support
PC VGA640 x 350 31.5 70
640 x 48031.5 60
3 37.9 723
37.5 753
43.3 853
ResolutionHorizontal 
Frequency 
(kHz)Ve r ti c a l  
Frequency 
(kHz)VESA 
StandardDVI 
SupportDisplay
DVI720 × 480 31.5 60
3Upscale 720 × 576 31.3 50
1280 × 72045 60
37.5 50
1980 × 1080i33.8 60
28.1 50
PC/
MAC/
WSResolutionHorizontal 
Frequency 
(kHz)Ve r t i c a l  
Frequency 
(kHz)VESA 
StandardDVI 
Support
PCSVGA 800 x 60035.1 56
33 37.9 60
48.1 72
46.9 75
XGA 1024 x 76848.4 60
33 56.5 70
60.0 75
68.7 85
MAC 
13”VGA 640 x 480 34.9 67
MAC 
16”SVGA 832 x 624 49.6 75
MAC 
19”XGA 1024 x 768 48.4 603
SXGA 1280 x 1024 64 6033
 Notes
•  
This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) 
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data 
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s 
operation manual.
•  When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
•  When projecting video images of an interlaced video signal, the intended image may not be projected 
when using the RBG input. In such cases, use the component input, S-video input or video input. 
						

							40
Appendix
Video Compatibility Chart
1. Component 1/2 support signal formats are Y/Pb/Pr, Y/Cb/Cr
2. VGA port support signal formats are RGsyncB, RGBHV or RGBCsysc
3. “U” means manual setting is needed
DTV
ResolutionH-Freq 
(kHz)V-Freq    
(Hz)Comp1    
SupportComp2 
SupportS-Video 
SupportCompos-
ite SupportVGA
SupportDVI
Support
SD Video NTSC 640x480i 15.73 59.94/603333
PAL 768x576i 15.63 503333
SECAM 768x576i 15.63 503333
NTSC-4.43UUUU
PA L - MUUUU
PA L - NUUUU
NTSC-JUUUU
PAL-60UUUU
NTSC-50
ED TV 480p 720x480p 31.5 59.94/6033 33
576p 720x576p 31.3 5033 33
HD TV 1080i/50 1920x1080i 33.8 5033 33
1080i/60 1920x1080i 28.1 59.94/6033 33
720p/50 1280x720p 37.5 5033 33
720p/60 1280x720p 45.0 59.94/6033 33
HTPC 720p/48 1280x720p 48
720p/75 1280x720p 75
SignalHorizontal Frequency (kHz)Vertical Frequency (Hz)DVI Support
480p 31.5 603
576p 31.3 503
720p 45.0 603
720p 37.5 503
1080i 33.8 603
1080i 28.1 503 
						

							Appendix
41
Troubleshooting
Problem Check
Projector does not startProjector power cord is not plugged into the wall outlet.
Remote control batteries have run out.
No pictureThe selected input mode is wrong.
Cables may be incorrectly connected to the rear panel of the projector.
Power to the external connected device is off.
The video signal format of the video equipment is not set correctly.
Color is fadedPicture adjustments are incorrectly set.
Picture is blurredFocus is incorrectly set.
The projection distance exceeds the focus range.
Picture contains noise(PC input only)
Try Auto tune.
Adjust the Clock setting.
Adjust the Phase” setting.
Picture is green on 
INPUT1 or 2 COMPONENTChange the input signal type of the video equipment.
Picture is dark or 
bright and whitishPicture adjustments are incorrectly set.
Picture is too bright 
and whitishPicture adjustments are incorrectly set. 
						

							42
Appendix
Product Specifications
Item Description
Model No. PD7130/PD7150 DLP Front Projector
DLP Panel
Display method: PD7130→0.65” WXGA, DC3. 
                           PD7150→ 0.8” HD2 + DC3
Device method: Digital Light Processing (DLP
®)
Display Type DLP Chip, RGB optical shutter method
Resolution 1280 x 720 pixels
Lens 7130: F2.4~2.5, f=19.1~23.9
7150: F2.36~2.5, f=24.0~30.1
Projection Lamp 250 W / 200 W switchable UHP lamp
Input Sources Video VGA
YCbCr, YPbPr1, 2
CVBS (Composite Video)
S-Video
DVI-D
Control RS-232 (For computer)
IR Receiver
12V trigger
Computer Compatibility VGA, SVGA, XGA, SXGA
2D Lens Shift Ability PD7130 Up / Down: +115% / -100%
PD7150 Up/Down: +100%/-65%
Left / Right: ± 15%
Brightness PD7130: 900 ANSI Lumen
PD7150: 1000 ANSI Lumen
Digital Keystone Correction 2D keystone correction
Projection Lens Zoom lens with manual focus and manual zoom adjust
Contrast Ratio PD7130: 4500:1
PD7150: 5000:1
Uniformity 90%
Screen Size 30 ~ 300 inches
Throw Ratio (16:9) 1.34:1 ~ 1.68:1
Aspect Ratio 16:9 Native
Projection Distance 1.7 m ~ 5.7 m
Video Enhance 4-Line Y/C separation(2D)
DLTi, DCTi
Projection Method Front / Rear, Desktop / Ceiling
OSD Control Projector keypad
IR remote control
Video system NTSC 3.58 / NTSC 4.43 / PAL / PAL-M / PAL-N / PAL 60 / SECAM / 
SDTV-480i/576i, EDTV-480p/576p, HDTV-720p/1080i
Dimensions
(W x L x H)PD7130: 445 mm x 420 mm x 180 mm (17.5 x 16.5 x 7.1)
PD7150: 445 mm x 420 mm x 180 mm (17.5 x 16.5 x 7.1)
Weight 17.6 lbs
Power Supply 100 ~ 240 V at 50 ~ 60 Hz
Power Consumption 370 W (Standby mode < 5W)
Operating Temperature 5°C to 35°C
Audible Noise 29dBA (Eco mode)
Specifications are subjected to change without notice.