Planar Pd7130 Projector User Manual

Connections and Setup
13
Connecting the Thumbscrew Cables
„Connect the cable making sure that it fits correctly into the terminal. 
Secure the connectors by tightening the screws on both sides of the 
plug.
„Do not remove the ferrite cores attached to the cable.
“Plug and Play” Function
„This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC 
compatible computer automatically send settings, allowing for quick and easy setup.
„Before using the “Plug and Play” function,...

14
Connections and Setup
Adjustable Leveling Foot
Adjusting the Lens
Use the adjustable foot to level the projector 
when it is placed on an uneven surface or 
when the screen is slanted.
The projected image can be made higher by 
adjusting the projector when it is lower than 
the screen.
1Hold the projector firmly and screw the 
adjustable foot to adjust the projector 
to the desired angle. 
2Lift the projector to the desired angle 
and screw the adjustable foot to fix the 
level.
•  If the screen is at...

Connections and Setup
15
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an 
optimal image.
Standard Setup (Front Projection)
„Place the projector at the required distance from the screen according to the desired picture size. (See 
page 16)
An Example of Standard Setup
 Notes
•  The projector lens should be perpendicular (square-on) to the screen. If the horizontal line passing 
through the lens center is not perpendicular to the screen,...

16
Connections and Setup
Screen Size and Projection Distance
When using a wide screen (16:9) project the image on the 
whole area of the 16:9 screen.
PD7130
PD7150
Screen Size (16:9) Projection DistanceDistance from lens center to the 
lower edge of the image 
Diagonal Width Height Max Min upper lower
60” (152 cm) 52” (132 cm) 29” (75 cm) 77 (2.3 m) 61 (1.8 m) 0” (0 cm) -2’5” (-75 cm)
70” (178 cm) 61” (155 cm) 34” (87 cm) 810 (2.7 m) 71 (2.1 m) 0” (0 cm) -2’10” (-87 cm)
80” (203 cm) 70” (177 cm) 39” (100...

Connections and Setup
17
Projection Mode
Rear mode:
„Place a translucent screen between the projector and the 
audience. Use the adjustable foot to level the screen 
angle.
Front mode: 
„Place the projector on a flat and stable object and adjust the 
projecting distance. Use the adjustable foot to level the screen 
angle.
Ceiling-mount setup
„The optional ceiling-mount bracket is recommended for this 
installation.
„Before mounting the projector, contact your nearest Authorized 
Service Center or Dealer...

18
Connections and Setup 

Basic Operation
19
Basic Operation 

Basic Operation
20
Image Projection
Basic Procedure
Connect the required external equipment to the projector before following these procedures.
 Info
The preset language is English. To change the on-screen display to another language, reset the language 
according to the procedure on page 31.
1Plug the power cord into the wall outlet.
•  The power indicator turns green, and the projector enters standby mode.
2Press   on the remote control or   on the projector.
•  The power indicator turns off, and the...

Basic Operation
21
3Press   on the projector to 
select the source.
 Notes
•  When a signal is not received, “Searching” is displayed.
•   If you select “Auto” as the input source, then the correct input source is automatically selected.
4To turn off the projector, press the   on the remote controller. Or press   on the 
projector and then   when the confirmation message is displayed.
 Notes
•  If you accidentally press power OFF and do not want to turn off the projector, press Exit or wait 
until the...

Basic Operation
22
Using the Menu Screen
You can use the menu screens to adjust 
the image and projector settings. You can 
operate the menus from the projector or 
remote control using the following 
procedure.
Menu Selections (Adjustments)
1Press   on remote or   on the keypad.
•  The menu screen is displayed.
 Note
•  The “Picture” menu screen for the selected input mode is displayed.
2Press S or T to select the menu you want to adjust.
3Press X or   to reach the Sub-menu and then press S or T to...