Planar Pd7010 Projector User Manual

31
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
Planar recommends changing the projection lamp after a warning message displays Warning: 
Lamp life time Over. It should only be replaced with a certifi ed replacement part, which you can 
order from your local dealer.
                      
Important!
The lamp contains a certain amount of mercury and should be disposed of 
according to local ordinance regulations.
Avoid touching the glass surface of the new lamp: Doing so may shorten 
its...

32
3.Remove the three screws from 
the lamp module.
4.Lift the module handle up.
5. Pull fi rmly on the module 
handle to remove the lamp 
module.
6. Reverse steps 1 to 5 to install 
the new lamp module. 

33
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1.Press the Menu button to open the OSD 
menu.
2. Press the cursor ◄ ► button to move to 
the Service menu.
3. Press the cursor ▲▼ button to move 
down to Lamp Hour Reset.
4. Press the cursor ◄ ► or Enter button. 
A message screen appears.
5. Press the cursor buttons in this order: 
▼ ▲ ◄  ►.
The Status menu appears again showing 
the Lamp Hours reset to zero.
Cleaning the Projector...

34
Using the Kensington® Lock
If you are concerned about security, attach one end of a security cable to a permanent object and 
the other to the Kensington slot and a projector. 
Contact your vendor for details on purchasing a suitable Kensington security 
cable.  The security lock corresponds to Kensington’s MicroSaver Security 
System. If you have any comment, contact: Kensington, 2853 Campus Drive, 
San Mateo, CA94403, U.S.A. Tel: 800-535-4242, 
http://www.Kensington.com. 

35
TROUBLESHOOTING
These guidelines provide tips to deal with problems you may encounter while using the projector. If 
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose 
connection. Check the following before proceeding to the problem-specifi c solutions.
Use some other electrical device to confi rm that the electrical outlet is working.
Ensure the projector is turned on.
Ensure all connections...

36
LED Error Messages
Before cooling, the LED will blink three (3) times in two (2) second intervals. The LED message is 
defi ned by the blinking sequence. A long blink is defi ned as 1 second.  A short blink is defi ned as 
0.3 seconds. The LED messages are listed below:
ERROR CODE MESSAGELED FLASH
Environment Over Temperature 1 long blink / 1 short blink
DMD Over Temperature  1 long blink / 2 short blinks
Lamp Over Temperature 1 long blink / 3 short blinks
Fan1 Locked
1 long blink / 4 short blinks
Fan2...

37
Common Problems and Solutions
This section describes some common problems and their solutions.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred 
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 7-meter (23-feet) specified range.
4. Check...

38
Remote Control Problems
Problem: The projector does not respond to the remote control 
1. Direct the remote control towards remote sensor on the projector. 
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced. 

39
SPECIFICATIONS
Hardware Specifi cations
MODELPD4010 PD7010 PD7060
Display typeTI DMD 0.55-inch x 1, 12 
degrees, DDR DMD with 
DDP2000TI DMD 0.65-inch x 1, 12 
degrees, LVDS DMD with 
DDP3020TI DMD 0.65-inch x 1, 12 
degrees, LVDS DMD with 
DDP3020
Resolution 480p (854x480) 720p (1280x720) 720p (1280x720)
Color 16.7 Million (24-bits/pixel)
Weight 4kg / 8.8lbs
Projection 
distance1.5 to 7 meters (59 to 275 inches)
Projection screen 
size0.76 to 3.81 meters (30 to 
150 inches)0.88 to 4.45 meters (35 to...

40
Input/output Connectors
MODELPD4010 PD7010 PD7060
PC RGB RGB RGB /DVI-D
VideoComposite video (RCAx1)
Mini-jack to S-Video (Mini-DIN)
Component (RCA x3)
DVI-D (HDCP)
None HDMI (HDCP) HDMI (HDCP)
Security Kensington slot