Planar Pd7010 Projector User Manual

11
Bottom View
ITEMLABELDESCRIPTION
1Ceiling support 
holesContact your dealer for information on mounting the projector on a
ceiling
2 Tilt adjuster Adjust angle of the picture
3Height adjuster 
buttonPush to release height adjuster
4 Height adjuster Adjuster drops down when adjuster button is pushed
2
1
3
4 

12
Remote Control Functions
ITEMLABELDESCRIPTION
1 Power on Turns projector power on
ON─ POWER─ OFF
1
23
45
SOURCE
2 Power off Turns projector power off
3 Source 1 User confi gurable (Default: HDMI)
4 Source 2User confi gurable 
(Default: Component)
5 Source 3 User confi gurable (Default: DVI-D)
6 Source 4 User confi gurable (Default: PC)
7 Source 5User confi gurable 
(Default: Video/S-Video)
8 Up cursor
Navigates and changes settings in the 
OSD
9 Left cursor
10 Enter Changes settings in the OSD
11 Right...

13
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point 
the remote directly at the projector. Provided you are not holding the remote control perpendicular 
to the sides, the remote control functions within a radius of about 10 meters (33 feet) and 30 
degrees above or below the projector level. If the projector does not respond to the remote control, 
move a little closer.  
Important!
Avoid using the remote control with...

14
SETUP AND OPERATION
Inserting the Remote Control Batteries
1. Remove the battery compart-
ment cover by sliding the cover 
in the direction of the arrow.
2. Insert the supplied batteries tak-
ing note of the polarity (+/-) as 
shown here.
3. Replace the cover.
CAUTIONCAUTION
Only use AAA alkaline batteries.
Dispose used batteries according to local ordinance regulations. 
Remove the batteries when not using the projector for prolonged periods. 1.
2.
3. 

15
Connecting Input Devices
A PC or notebook computer as well as video devices can be connected to the projector at the 
same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders , 
digital still cameras and high defi nition sources. Check the user manual of the connecting device 
to confi rm it has the appropriate output connector.
  
As a safety precaution, disconnect all power to the projector and connecting 
devices before making connections.  

16
Starting and Shutting down the Projector
1. Remove the lens cover.
2. Connect the power cord to the projector. 
Connect the other end to a wall outlet.
3. Press the Power button. The Power LED 
on the projector turns on. Turn on the con-
nected devices.
4. The language selection screen appears 
(Initial setup only). Select the desired lan-
guage. 
1.  Press the cursor ▲▼ button until 
Language is highlighted. 
2.  Press the cursor ◄ ► or Menu button 
to confi rm the language, and close the 
OSD.
 
5....

17
Adjusting the Projector Level
Take note of the following when setting up the projector:
• The projector table or stand should be level and sturdy.
• Position the projector so that it is perpendicular to the screen.
• Be sure cables are not in the way or can cause the projector to be knocked over.
1. To raise the level of the projector, lift the 
projector and press the height-adjuster 
button [A]. 
The height adjuster drops down [B]. 
2. To lower the level of the projector, press 
the height-adjuster...

18
Adjusting the Focus and Zoom
1. Locate the image zoom and focus 
adjustment rings on the projector. Zoom   Focus
2. Use the image zoom control to resize the 
projected image and screen size.
3. Rotate the image focus control to sharpen 
the projected image. 

19
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings. 
When the projector is turned on, any connected devices are detected. If the connected device is 
a PC, press the appropriate keys on the computer keyboard to switch the display output to the 
projector. (Check the user manual of the PC to determine the appropriate Fn key combination to 
change display output.)
Navigating the OSD
You can use the remote...

20
Setting the OSD Language
You may want to reference the OSD on your projector while reading this section. Set the OSD 
language to your preference before continuing. (The default language is English.) 
Press the Menu button. The Image menu appears.
Press the cursor ◄ ► button until Language is highlighted. 
Press the cursor ▲▼ button until the desired Language is highlighted. 
Press the Menu button to confi rm the language, and close the OSD. 1.
2.
3.
4.