Pioneer Rvd Xg10 Projector Specifications

							RVD-XG10
RS-232C
COMMAND MANUAL
Ver.1.00 
						

							CONTENTS
----------------------------------------------------------------------------------------------------------------
1. CONNECTIONS
2. COMMANDS
 2.0 Command List
 2.1 Basic Commands
 2.2 Setup Commands
 2.3 Adjustment Commands
 2.4 Reset Commands
 2.5 Integrator Commands
3. NOTES 
						

							1. CONNECTIONS
----------------------------------------------------------------------------------------------------------------
(1) Communication software setup
The interface used complies with the RS-232C. Set the communication software as listed below.
Baud rate : 9600 bps
Number of bits : 7 bits
Parity : Non parity
Stop bit : 1 bit
(2) Computer connection
Connect an external computer using a straight cable with 9-pin, D-SUB connectors.
The connectors should be wired as shown below.
Fig. 1  Connector Configuration
  Fig. 2  9-pin D-SUB Connector 
						

							2. COMMANDS
----------------------------------------------------------------------------------------------------------------
 2.0 Command List
 The following tables show the availability of each command according to the status of the set. Each command is
available in the conditions marked .  (C) indicates that the command is available only when the COMP. 1 or COMP.
2 input is selected, and  (V) indicates that it is available only when the video input is selected. a, aa and b in the
Command columns indicate character strings, and dd and dddd indicate figures from 0 to 9 or sign (-).
 The Function columns describe only the simple descriptions. Refer to the Instruction Manual for details.
Table 1  Basic Commands
Standby Power
ONSet
MenuONRS-232C
Adjust
ON
PON
POF
INaa =V/1/2
AKaa =Y/N
EOaa =N/F
MSaa =Y/N
GST
GPP
GAD
AJY
AJN CommandSet StatusFunction
Checks the mode setting value.Activates the RS-232C adjustment mode.Deactivates the RS-232C adjustment mode. Turns the power of the set ON.
Switches the echo-back display ON/OFF.
Switches the message display ON/OFF.Checks the status.Checks the picture quality/adjustment data. Turns the power of the set OFF.
Switches the input.
Switches the acknowledgment display ON/OFF.Table 2  Setup Commands
StandbyPower
ONSet
MenuONRS-232C
Adjust
ON
VON
VOF
AON
AOF
CLMaa =S/V›(C)
VSaa =A/P/S/3/4/M/N›(V)
DSPaa =Y/N
LGaa =E/F/D/S/I/J
RPaa =N/H/V/F
BGaa =0/1
OTaa =L/1/2/X
AIaa =L/V/1/2Sets the audio input.
SZaa =E/TSets the resized display.›(C)
a =MU/MD/PU/PD
     /PL/PR/ON/OF DZaa›(C) Sets digital zooming.Sets the background color.Sets the computer output. Sets the color mode.
Sets the video system.Switches the on-screen display ON/OFF.Sets the display language. CommandFunctionSet StatusSets the reverse picture. Deactivates video muting.
Activates video muting.
Deactivates audio muting.Activates audio muting. 
						

							Table 3  Adjustment Commands
Standby Power
ONSet
MenuONRS-232C
Adjust
ON
ZUP
ZDW
FUP
FDW
VOLdddd = 0 to 60
FRQdddddddd = 264 to 4104›(C)
PHSdddd = 0 to 19›(C)
PSaa =L/R/U/D›(C)
ATS›(C)
CNTdddd = -51 to 0
BRTdddd = -25 to 25
COLdddd = -25 to 25Adjusts the color.›(V)
TNTdddd = -25 to 25Adjusts the tint.›(V)
SHPdddd = -25 to 25Adjusts the sharpness.›(V)
Caba =R/B, b =L/R/U/DAdjusts the convergence.Set StatusCommand Function
Zooming toward Wide-angle.
Zooming toward Telescopic.
Focusing toward Far.Focusing toward Near.Automatic setup of the computer screen.Adjusts the contrast.Adjusts the brightness. Adjusts the volume.
Adjusts the sampling clock (count).
Adjusts the position of screen.Adjusts the sampling clock (phase).Table 4  Reset Commands
StandbyPower
ONSet
Menu
ONRS-232C
Adjust
ON
PPMRST
TITRST
LMPRSTResets to initial setup.Resets the lamp life counter. CommandFunctionSet StatusResets the picture quality/adjustment values.Table 5  Integrator Commands  Note: Effective only when the set is started in the integrator mode.
Standby Power
ONSet
Menu
ONRS-232C
Adjust
ON
GIT› Note
IaCa =R/G/B› Note
IaBa =R/G/B› NoteSet StatusChecks the integrator mode setting values.Checks the sub-contrast.Checks the sub-brightness. CommandFunction 
						

							2.1 Basic Commands
       Command NameFunction
2.1.1  PON/POF Power ON/OFF switching.
2.1.2  INV/IN1/IN2 Input selection.
2.1.3  AK, EO, MSTransmission/reception check.
2.1.4  GST, GPP, GAD Current set status check.
2.1.5  AJY/AJN Start/end of adjustment using commands. 
						

							2.1.1  PON/POF Commands
----------------------------------------------------------------------------------------------------------------
Function: Switches the power mode between standby  power ON.
----------------------------------------------------------------------------------------------------------------
Syntax: PON[CR], POF[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function::
  Remote   : [STANDBY/ON]  * Cyclic selection.
  Main unit: [STANDBY/ON]  * Cyclic selection.
----------------------------------------------------------------------------------------------------------------
 These commands switch respectively the standby mode to power ON mode and the power ON mode to standby mode.
 The current mode can be checked with the GST command.
    PON: Switching from the standby mode to the power ON mode.
    POF: Switching from the power ON mode to the standby mode. 
						

							2.1.2  INV/IN1/IN2 Commands
----------------------------------------------------------------------------------------------------------------
Function: Selects the input.
----------------------------------------------------------------------------------------------------------------
Syntax: INV[CR], IN1[CR], IN2[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function::
  Remote:    [COMP. 1], [COMP. 2], [VIDEO]
  Main unit: [INPUT]  * Cyclic selection.
----------------------------------------------------------------------------------------------------------------
 These commands switches the input to the set.
 The current input selection can be checked with the GST command.
    INV: Selection of the video input.
    IN1: Selection of the COMP. 1 input.
    IN2: Selection of the COMP. 2 input.
----------------------------------------------------------------------------------------------------------------
Note: These commands can be issued only in the menu OFF mode.
      Digital zooming is deactivated when any of these commands is issued. 
						

							2.1.3  AK, EO and MS Commands
----------------------------------------------------------------------------------------------------------------
Function: Checks the transmission and reception through RS-232C.
----------------------------------------------------------------------------------------------------------------
Syntax: AKY[CR], AKN[CR], EN[CR], EOF[CR], MSY[CR], MSN[CR]
----------------------------------------------------------------------------------------------------------------
Initial status: AKY, EON, MSY
----------------------------------------------------------------------------------------------------------------
Equivalent function:: None
----------------------------------------------------------------------------------------------------------------
 These commands checks operations through the RS-232C line.
    AKY/AKN:
     Acknowledgment ON/OFF.
     These commands make it possible to output ACK (0x06) indicating normal completion or NAK (0x15) indicating
abnormal
    completion as the check signal to be returned after command execution.
    EON/EOF:
     Echo-back ON/OFF.
     These commands make it possible to output the echo-back of input commands.
     They can be used to check the circuit connection, etc.
    MSY/MSN:
     Status display ON/OFF.
     These commands make it possible to output the current status when the GST, GPP or GAD command is executed.
     A message is output when the AJY status is activated, the AJY status is deactivated or the set is switched from
    the standby mode to power ON mode.
      AKY: Setting so that the acknowledgment is returned.
      AKN: Setting so that the acknowledgment is not returned.
      EON: Setting so that the echo-back is returned.
      EOF: Setting so that the echo-back is not returned.
      MSY: Setting so that the status data, etc. are returned.
      MSN: Setting so that the status data, etc. are not returned. 
						

							2.1.4  GST, GPP and GAD Commands
----------------------------------------------------------------------------------------------------------------
Function: Checks the current status of the set.
----------------------------------------------------------------------------------------------------------------
Syntax: GST[CR], GPP[CR], GAD[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function:: None.
----------------------------------------------------------------------------------------------------------------
  GST command: Input GST[CR] to check the current status of the power, input, muting, volume, etc.
    Example 1: Status display in standby mode
POWER OFF
    Example 2: Status display when video input is selected
Ver. 1.00A  ...1
ID:**
INV:SIN/NTS  ...2
AOF/VON  ...3
 AJY  ...4
VOL:  8  ...5
DMG  ...6
    1. Version information
    2. Input status
       (Section corresponding to INV in Example 2)
        INV: Video input
        IN1: COMP. 1 input
        IN2: COMP. 2 input
       (Section corresponding to SIN in Example 2 ... Video input)
        SIN: S-VIDEO input
        VIN: Ordinary (composite) video input
       (Section corresponding to NTS in Example 2 ... Video input)
        NTS: NTSC mode video
        PAL: PAL mode video
        443: 4.43 NTSC mode video
        NPL: N PAL mode video
        MPL: M PAL mode video
        SEC: SECAM mode video
        B/W: Black/white mode (Used when the video format cannot be identified)