Philips Proscreen Pxg30 Inpact Projector User Manual

41
12. MaintenanceLamp Replacement
Lamp Replacement
When the life of the Projection Lamp of this projector draws to an
end, the Lamp Indicatorlights yellow.  If this indicator lights
yellow, replace the projection lamp with a new one promptly.
Turn off the projector and disconnect the AC plug.  Allow the
projector to cool for at least 45 minutes.
Loosen 2 screws with a screwdriver and pull out the Lamp
Assembly by grasping Handle.
1
3
Replace the Lamp Assembly with a new one and tighten the 2
screws back...

42
Lamp Replacement12. Maintenance
Lamp Replace Counter Reset
Be sure to reset the Lamp Replace Counter after the Lamp
Assembly is replaced.  When the Lamp Replace Counter is reset,
the Lamp Indicatorwill light off.
Note :Do not reset the Lamp Replace Counter when the Projection Lamp is not  replaced.
1
2
3
This projector uses a high-pressure lamp which must be handled carefully and properly.  Improper
handling may result in accidents, injury, or create a fire hazard.
–  Lamp lifetime may differ from...

43
Troubleshooting
Before calling your dealer or service center for assistance, check the matters below once again.
–  Make sure you have properly connected the projector to peripheral equipment as described in the section Installation on
page15 and 16. 
–   Make sure all equipment is connected to AC outlet and turned on the power.
–   When you operate the projector with a computer, and it does not project an image, restart the computer.
No power.–  
Plug the power cord of the projector into the AC...

44
13. AppendixTroubleshooting
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions,
contact a Philips Authorised LCD Projector Dealer or
Service Centre. Give the model number and explain the difficulty.  Advice to obtain service will be given.
The Remote Control 
does not work.–  
Check the batteries.
–  
Make sure no obstruction is between the projector and the remote control.
–  
Make...

45
Indicators and Projector Condition13. Appendix
Indicators and Projector Condition
Check the Indicators for projector condition.  
• • • on• • • dim• • • off• • • flashing
✽When the life of the projection lamp draws to an end, the Lamp Indicatorlights yellow.  When this indicator lights yellow, replace
the projection lamp with a new one promptly.  Make sure to reset the Lamp Replace Counterafter its replacement.
The projector is Off.  (The AC power cord is unplugged.)
The projector is ready to be...

46
System SVGA 1VGA 1 MODE 1 MODE 2- - - - - -
Auto imageFine sync.Total dotsHorizontalVerticalCurrent modeClampDisplay area
Display area - HDisplay area - VFull screenResetMode freeStore
Quit
StandardRealImage 1Image 2Image 3Image 4
Image AdjustContrastBrightnessColor temp.
RedGreenBlueGammaResetStore
Quit
NormalTrueWideDigital zoom +Digital zoom –
0 - 31
On / Off
0 - 630 - 63
Input
Data 2
Data 
RGB( Scart )  
System 
System 
Data 3Data ( In )
Data ( Out )
System 
Data Input
Main menu
Main menu...

47
13. AppendixMenu Tree
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
Main menu
Video Input
Auto1080i1035i720p575p480p575i480i
StandardCinemaImage 1Image 2Image 3Image 4
Quit
NormalWide
0 - 630 - 630 - 630 - 63
On / OffL1 / L2 / Off
Main menu
Settings
VolumeMuteQuitOn / Off
Language
2)
3)
Image Select
System 
System 
Image AdjustContrastBrightness
Color temp.
ColorTintXLowLowMidHigh
RedGreenBlueSharpness
ResetStore
GammaNoise reductionProgressive 
0 - 630 - 630 - 630 - 310 - 15
Image 1Image 2Image 3Image 4...

48
Device
D1
on
D2
BrandCode input( 4 digit )
Proj. PXG30
Next
off
video
S-video
D3
lens
zoom - / +
YPbPr
Feature
V-effect
lens shift - / +
D-freeze
timer
mouse
Cursor pointer
D-keyst  -  reset
focus - / +
auto
D-zoom - / +
mouse left / right
OK
Cancel
Code set
Code canceledUse
Mode
Remote Control Code Set
1/4
2/4
3/4
4/4
f
f
f
✽stands for the hard buttons on the remote control.
Menu Tree13. Appendix
Menu Tree (Remote Control) 

49
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140
MHz of Dot Clock.
Note : Specifications are subject to change without notice.
On-Screen
DisplayResolutionH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x...

50
13. AppendixTechnical Specifications
Technical Specifications
LC1345/00 : 3 x 1.0 HT Poly Silicon TFT with µlens
Multi-media Projector
7.9 kg  (17.4 lbs)
306mm x 166mm x 436mm  (12.0 x 6.5 x 17.2 )  (W x H x D) 
XGA (1024 x 768 ), RGB Stripe
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 300
”
800 TV lines (video input)
2W + 2W Stereo
+5 ˚C ~ +35 ˚C (41 ˚F ~ 95 ˚F)
-10 ˚C ~ +60 ˚C (14 ˚F ~ 140 ˚F)
Printed...