Philips Mcd122 User Manual

							12
Option 3: Connect through 
composite video
 
1  Connect the supplied composite video 
cable to:
 the VIDEO OUT socket on this unit.
 the video input socket on the TV.
Connect audio cables
 
1  To play sound from the TV through this 
unit, connect audio cables (red/white - not 
supplied) to:
 the AUX IN L/R sockets on this unit.
 the audio output sockets on the TV.
TV
8
TV
L  AUDIO OUT  R
8
Note
  !
/@@
(	
@%
when a progressive scan TV is connected.
  If your TV does not suppor t progressive scan, you 
cannot view the picture.
  For how to activate progressive scan on your TV, refer 
to the TV user manual.
Connect a progressive scan TV through 

$
	@
#
!/!(	@
;
1  Connect component video cables (red/
blue/green - not supplied) to:
 the VIDEO OUT (Pr/Cr Pb/Cb Y) 
sockets on this unit.
 the component input sockets on the 
TV.
Option 2: Connect through S-Video
 
1  Connect an S-video cable (not supplied) 
to:
 the S-Video socket on this unit.
 the S-Video socket on the TV.
TV
S-VIDEO IN
8
EN
 
						

							13
4 Get started
Caution
  
Use of controls or adjustments or performance of 
procedures other than herein may result in hazardous 
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in 
(;
If you contact Philips, you will be asked for the 
model and serial number of this apparatus. The 
model number and serial number are on the 
bottom of the apparatus. Write the numbers 
here: 
Model No. ____________________________
Serial No. _____________________________
Prepare the remote control
Caution
  
Risk of explosion! Keep batteries away from heat, 
!
;@%		;
!

#
1  Remove the protective tab to activate the 
remote control batter y.
To replace the remote control batteries: 
1  Open the batter y compar tment.
2  Inser t one lithium CR2025 batter y with 
correct polarity (+/-) as indicated.
3  Close the batter y compar tment.
Note
  Before you press any function button on the remote 

	
)			!
	
	!	!$
	
control.
  If you are not going to use the remote control for a 
long time, remove the batter y.
Connect power
 
Caution
  
Risk of product damage! Ensure that the power supply 
voltage corresponds to the voltage printed on the back 
or the underside of the unit.
  Before connecting the AC power cord, ensure you have 
completed all other connections.
1  Connect the AC power cord to the wall 
socket.
8English
EN
 
						

							14
3  Turn on the TV and switch to the correct 
video-in channel in one of the following 
ways:
 Go to the lowest channel on your TV, 
then press the Channel Down button 
until you see the blue screen.
 Press the source button repeatedly on 
the remote control of your TV. 
Tip
  The video-in channel is between the lowest and highest 
channels and may be called FRONT, A/V IN, VIDEO etc. 
See the TV user manual on how to select the correct 
input on the TV.
Select the correct TV system
Change this setting if the video does not appear 
correctly. By default, this setting matches the 
most common setting for TVs in your countr y.
1 Press SYSTEM MENU.
2 Select [Video Setup].
3 Select [TV System] and then press .
4  Select a setting and then press OK.
[NTSC] - For TV with NTSC color 
system. 
[PAL] - For TV with PAL color system.
[Multi] - For TV that is compatible 
with both PAL and NTSC .
5  To exit the menu, press SYSTEM MENU.
Change system menu 
language
1
 Press SYSTEM MENU.
2 Select [General Setup].
3 Select [OSD language] and then press .
4  Select a setting and then press OK.
5  To exit the menu, press SYSTEM MENU.
Set clock
1
  In the standby mode, press and hold 
CLOCK to activate the clock setting 
mode.
  »The hour digits are displayed and begin 
to blink.
2 Press + VOL  - to set the hour, then press 
CLOCK again.
  »The minute digits are displayed and 
begin to blink.
3 Press + VOL  - to set the minute.
4 Press CLOCK	

$	!
		/;
Turn on
1
 Press .
  »The unit switches to the last selected 
source.
Switch to standby mode
1  Plug in AC power.
  »The unit will go to Eco Power Standby.
2 Long press .
  »Switch the unit from Eco Power 
Standby mode to Standby mode.
Tip
  In the Eco Power mode, you can press CLOCK key to 
switch to the standby mode and view the clock (if set).
Find the correct viewing 
channel
1
 Press  to turn on the unit.
2 Press DISC to switch to disc mode.
EN
 
						

							15
5 Play
Note
  	!
$	)$##;
Play a disc
Caution
  
Never look at the laser beam inside the unit.
  Risk of product damage! Never play discs with 
accessories such as disc stabilizer rings or disc 
treatment sheets. 
  Never put any objects other than discs into the disc 
compar tment.
1 Press DISC to select the DISC source.
2 Press  on the front panel.
  »The disc tray opens.
3  Place a disc onto the tray and press .
  »Ensure that the label faces up.
4  Play star ts automatically.
 To stop play, press 
.
 To pause or resume play, press 
.
 To skip to the previous/next title/
chapter/track, press 
/.
If play does not start automatically:
 Select a title/chapter/track and then 
press 
.
Tip
  To play a locked DVD, enter the 4-digit parental control 
password.
Use the disc menu
When you load a DVD/(S)VCD disc, a menu 
may be displayed on the TV screen.
Turn on Progressive Scan
Progressive scan displays twice the number of 
frames per seconds than interlaced scanning 
(ordinar y TV system). With nearly double the 
number of lines, progressive scan offers higher 
	
	
(	;
Before you turn on this feature, ensure that:
 The TV suppor ts progressive scan signals.
 You have connected this unit with the TV 
through component video.
1  Turn on the TV.
2  Ensure that the TV progressive scan mode 
is deactivated (see the TV user manual).
3  Switch the TV to the correct viewing 
channel for this unit.
4 Press DISC.
5 Press SYSTEM MENU.
6 Press / to select [Video Setup] in the 
menu, then press 
.
7 Select [Component Video], then press .
8 Select [P-Scan], then press OK.
  »The progressive setup is complete.
English
EN
 
						

							16
Play from USB
Note
  Ensure that the USB device contains playable music, 
pictures or video.
1  Inser t the USB device.
  
2 Press USB to select the USB source.
3 Press / to select a folder, then press OK 
	

$;
4 Press /	
	#
$	!#
;
5 Press  to star t play.
 To stop play, press 
.
 To pause or resume play, press 
.
 
	
	!@
}	)
/.
 To return to the upper-level menu, 
press DISC MENU, and then press 
OK 	

$;
Play DivX video
~
@
						

							17
Play control
=	>
?		

1  During play, press MODE/DIM repeatedly 
	
		
	

	!!#?
mode.
 To resume normal play, press MODE/
DIM repeatedly until no option is 
displayed.
Repeat A-B  (DVD/VCD/CD/MP3/
@JQ
1  During music or video play, press A-B at 
the star t point.
2 Press A-B at the end point.
  »The selected section star ts to play 
repeatedly.
 To cancel repeat play, press A-B again.
Note
  The section A and B can be set only within the same 
track/title.
Search forward/backward
1  During play, press / repeatedly to 
select a search speed.
 To resume play at normal speed, press 
.
Search by time or chapter/track 
number
1  During video/audio play, press G OTO 
		$
!		
displayed.
 
						

							18
Change the audio channel
Note
  This feature is only available for VCD/DivX play.
1  During play, press AUDIO repeatedly to 
select an audio channel available on the 
disc:
 Mono Left
 Mono Right
 Stereo
Select a camera angle
Note
  This feature is only available for DVDs recorded with 
multiple camera angles.
1  During play, press ANGLE/PROG 
repeatedly to select a camera angle.
Picture view options
Preview pictures
1  During play, press .
  »The pictures in the current folder are 
displayed.
2 Press / to select a picture from the 
folder.
  »A thumbnail of the selected picture is 
displayed in the right pane.
3 Press OK to star t slideshow from the 
selected picture.
Rotate picture
1  During play, press /// to rotate the 
picture anti-clockwise/clockwise.
 Play star ts automatically at your 
selected point.
Resume video play from last stopped 
point
Note
  This feature is only available for DVD/VCD play. 
1  In stop mode and when the disc has not 
been removed, press 
.
To cancel resume mode and stop play 
completely:
1  In stop mode, press .
Play options
Display play information
1  During play, press DISPLAY/RDS 
repeatedly to display play information.
Zoom in/out image
1  During video play, press  (ZOOM) 
repeatedly to zoom in/out the image.
 When the image is zoomed in, you 
can press 
/ to pan through the 
image.
Slow-motion play
1  During video play, press  (SLOW) 
repeatedly to select a slow play option.
  »The sound is muted.
  »To resume play at normal speed, press 
.
EN
 
						

							19
[All] – If the connected device suppor ts 
multi-channel audio formats, select this 
option.
[Night Mode]
Make loud sound level softer and soft sound 
level louder so that you can watch the DVD 
movies at a low volume, without disturbing 
others.
[On]
						

							20
[Parental Control]
Restricts access to discs that are unsuitable for 
children. These types of discs must be recorded 
with ratings.
Press OK.
Select a rating level, then press OK.
Press the numeric keys to enter the password.
Note
  Rated discs above the level you set in [Parental 
Control](
	
%;
  The ratings are countr y-dependent. To allow all discs to 
play, select [8. Adult].
  Some discs have ratings printed on them but are not 
recorded with ratings. This function has no effect on 
such discs.
[Password]
This setting allows you to change the password 
for parental control. The default password is 
0000.
1) Press the numeric keys to enter ‘0000’ or 
your last set password at [Old Password];
2) Enter the new password at [New 
Password];
3) Enter the new password again at ^%
new password];
4) Press OK to exit the menu.
Note
  If you forget the password, enter ‘0000’ before you set 
a new password.
[Version Info]
Display the software version of this apparatus.
[Default]
Resets all the settings of this unit to factor y 
default, except for the password and parental 
settings.
[Picture Setting]
Customize picture color settings.
  
[Component Video]
Set the video output according to the video 
connection. If the composite connection is used, 
	!		/
	(;
[S-VIDEO] – If the S-Video connection is 
used, select this option.
[Interlaced] – For ordinar y TV: turn on the 
interlace mode.
[P-Scan] – For progressive scan TV: turn on 
the progressive scan mode.
Preferences
On the [Preferences] page, you can set the 
following options:
[Audio]
Select the preferred audio language for disc 
play.
  
[Subtitle]
Select the preferred subtitle language for disc 
play.
[Disc Menu]
Select the preferred disc menu language.
Note
  If the language you have set is not available on the disc, 
the disc uses its own default language.
  For some discs, the subtitle/audio language can only be 
changed from the disc menu.
[DivX Subtitle]
Select a character set that suppor ts the DivX 
subtitle.
Note
  
						

							21
Program radio stations 
manually
Note
  You can program a maximum of 20 preset radio 
stations.
1  Tune to a radio station.
2 Press ANGLE/PROG to activate 
programming.
3 Press / to allocate a number from 
1 to 20 to this radio station, then press 
ANGLE/PROG	

$;
  »!	$%	!#(
of the preset station are displayed.
4  Repeat the above steps to program other 
stations.
Note
  To overwrite a programmed station, store another 
station in its place.
Tune to a preset radio station
1
 Press / to select a preset number 
that you want.
Tip
  You can also use the numerical keypad to select a 
preset station directly.
7  Tune to FM 
radio stations
1  Ensure that you have connected and fully 
extended the supplied FM antenna.
2 Press TUNER.
3  Press and hold /.
4 !	!#(	
	 		

change, release the button.
  »The FM tuner tunes to a station with 
strong reception automatically.
5  Repeat steps 3-4 to tune to more stations.
To tune to a weak station: 
Press 
/		

	$
reception.
Program radio stations 
automatically
Note
  You can program a maximum of 20 preset radio 
stations.
1 Press / to select a preset number to 
star t programing.
2  Press and hold ANGLE/PROG for 
2 seconds to activate automatic 
programming.
  »[AUTO]