Philips Hts9540 User Manual

							19
Listen to music
1 Dock your iPod or iPhone (see ‘Dock your iPod or iPhone’ on page 999).
2 Press  DOCK for iPod on the home theater 
remote control.
 » The pla

ylists are displayed on the TV.
3 Press the Navigation buttons  and OK to 
select and play tracks.
Watch video or view slideshows
Note
 •On iPod, enable the T V ON set ting. •On iPhone, select the T V Out option.
1 Dock your iPod or iPhone (see ‘Dock your  iPod or iPhone’ on page 999).
2 Switch the T V to the AV/ V I D E O  source 
(corresponding to the yellow composite 
cable).
 » The 

TV screen goes blank.
3 Browse on the iPod or iPhone screen to select videos or photos.
4 Press  (Play ) to play the video and photos.
 » The picture is displa

yed on the TV. 
Use Philips EasyLink
The home theater suppor ts Philips EasyLink, 
which uses the HDMI CEC (Consumer 
Electronics Control) protocol. EasyLink-
compliant devices that are connected through 
HDMI connectors can be controlled by a single 
remote control. 
Note
 •Philips does not guarantee 10 0% 
interoperability with all HDMI CEC devices.
1 Switch on the HDMI CEC operations on the T V and other connected devices. See 
the manual of the T V or other devices for 
details. 
2 Press  (Home ).
Play audio from TV or other 
devices
Press  SOURCE  / AUDIO SOURCE  repeatedly 
to select the audio output of the connected 
device. 
Play from an MP3 player
Connect	and	play	audio	files	from	an	MP3	player	or other exter nal audio devices.
1 Connect the MP3 player to the home theater as described in the Quick star t 
guide. 
2 Press  SOURCE  / AUDIO SOURCE  
repeatedly until ‘ MP3 LINK’ appears on the 
display panel.
3 Press the but tons on the MP3 player to  select 	 and 	 play 	 audio 	 files.
Play from an iPod or iPhone
By connecting and installing a Philips Dock for 
iPod/iPhone, you can use the home theater to 
play music, movies and photos from your iPod or 
iPhone.
Note
 •You can charge your iPod/iPhone on the dock 
while the home theater is in iPod mode.
Dock your iPod or iPhone
1 Move the slide at the bot tom of the dock to ‘ STANDARD ’, then connect the dock to 
the home theater.
2 Connect the yellow composite cable from  the dock to the T V. 
3 Switch on the iPod or iPhone and place it in the dock.
4 On the home theater remote control, press  (Home ), then select [browse iPod]  and 
press OK .
English
EN
 
						

							20
5 Change settings
This section helps you to change the settings of 
your home theater. 
Caution
 •Most	of	the	set tings	are	already	configured	w
ith the best value for the home theater. 
Unless
	 you 	 have 	 a 	 specific 	 reason 	 to 	 change 	 a 	
s

et ting, it is best to leave it at the default value.
Access the setup menu
1 Press  ( Home ).
2 Select  [Setup], then press OK .
 »The setup men

u appears.
3 Select a setup menu, then press OK .
See the following sections for information 
about how to change the set tings of your 
home theater.
4 Press  BACK  to return to the previous 
menu, or press  to exit.
Note
 •You cannot change a set ting that is grayed out.
Change video settings
1 Press  ( Home ).
2 Select  [Setup], then press OK .
3 Select [ Video], then press OK .
4 Select and adjust the following set tings:
•	[TV Display]: Selects a picture display 
format 	 to 	 fit 	 the 	 T V 	 screen.
•	[HDMI Video]: Selects the HDMI 
video resolution.
•	[HDMI Deep Color]: Displays colors 
with more shades and hues when 
the video content is recorded in 
Deep Color and the T V suppor ts this 
feature.
3 Select  [Setup], then press OK .
4 Select [EasyLink]  > [EasyLink] , then press 
OK .
5 Select  [On], then press OK .
6 You can now enjoy the following Philips 
EasyLink controls. 
One-touch play
When you play a disc, the T V automatically 
switches to the correct channel.
One-touch standby
When you press and hold 
 (Standby ) on the 
remote control, the home theater and all the 
connected HDMI CEC devices (if they suppor t 
one-touch standby) switch to standby mode 
simultaneously.
System Audio Control
When you play a device that has its audio 
output routed to the home theater, the home 
theater switches to the corresponding audio 
source automatically.
To use one-touch audio, enable this feature and 
follow the instructions on the T V to map the 
connected devices correctly to the audio input 
jacks of the home theater.
Audio Input Mapping
Updates audio input mapping if there are new 
devices connected.
EN
 
						

							21
5 Press OK	 to 	 confirm 	 your 	 choice.
Note
 •For set tings related to HDMI, the T V must be 
connected through HDMI.
 •Night mode is available for Dolby encoded 
DVD and Blu-ray discs (for models suppor t 
Blu-ray playback).
Set up surround sound 
automatically
When	you	set	up	the	home	theater	for	the	first	time
, the setup menu prompts you to calibrate 
your speakers for the best surround sound. If you 
move your speakers or change the layout of the 
room, calibrate the speakers again to continue 
getting the best sound.
Before you star t, make sure that the calibration 
microphone is less than 5m from each of the 
speakers. If it is more, set up your sound manually 
(see ‘Set up surround sound manually’ on page 22).
1 Connect your speakers and subwoofer as  described in the Quick Star t. For the best 
surround sound, turn your rear speakers to 
face your listening position.
2 Connect the calibration microphone to the MP3 LINK connector on your home theater 
and place it in your usual listening place, at 
ear height.
   
  
•	[Component Video] : Selects the 
component video resolution. Copy-
protected DVDs can display only 
480p/576p or 480i/576i.
•	[Blu-ray 3D video] : Selects the 
3-dimensional video output when you 
play a 3D video on your home theater. 
The home theater must be connected 
to a 3D T V through HDMI.
•	[Picture Settings] : 	 Selects 	 a 	 predefined 	c
olor setting.
5 Press  OK	 to 	 confirm 	 your 	 choice.
Note
 •The best set ting is automatically selected for 
the T V. If you change the set ting, ensure that 
the T V suppor ts the new set ting. 
 •For set tings related to HDMI, the T V must be 
connected through HDMI.
 •For set tings related to progressive or 
component video, the T V must be connected 
through Component Video.
Change audio settings
1 Press  (Home ).
2 Select  [Setup], then press OK .
3 Select [Audio], then press OK .
4 Select and adjust the following set tings:
•	[Night Mode]: Selects quiet or full 
dynamic sound. Night mode decreases 
the volume of loud sounds and 
increases the volume of sof t sounds 
such as speech.
•	[HDM I Audio] : Selects HDMI audio 
format or disables HDMI audio output 
for the T V.
•	[360Sound Setup] : Calibrates the 
speakers to 360 degrees  SOUND 
SET TINGS when a calibration 
microphone is connected to the home 
theater.
•	[Speaker Setup] : Sets the volume level 
and distance of each speaker to obtain 
the best possible surround sound 
based on your room setup.
English
EN
 
						

							22
•	[View Network Settings] : Displays 
the current network set tings.
•	[View Wireless Settings]  : Displays the 
current Wi-Fi set tings.
•	[Net TV User Location] : Selects the 
location for accessing Net T V content 
and ser vices.
•	[Clear Net TV Memory] : Clears Net 
T V memor y, delete the temporar y 
downloaded
	 files 	 (e.g., 	 cookies) 	 of 	 the 	
N

et T V browser.
5 Press  OK	 to 	 confirm 	 your 	 choice.
Set up EasyLink
1 Press  (Home ).
2 Select  [Setup], then press OK .
3 Select [EasyLink] , then press OK .
4 Select and adjust the following set tings: 
•	[EasyLink] : Enables or disables EasyLink.
•	[One Touch Play] : Enables or disables 
One Touch Play.
If enabled, you can use the remote 
control to star t disc play in the 
home theater and the T V switches 
automatically to the correct channel.
•	[One Touch Standby] : Enables or 
disables One Touch Standby.
If enabled, the home theater can 
be switched off to standby by a 
remote control from the T V or other 
connected HDMI CEC devices.
•	[System Audio Control]  : Enables or 
disables System audio control.
If enabled, follow the instructions on 
the T V to map the connected devices 
correctly to the audio connectors of 
the home theater. The home theater 
switches automatically to the audio 
source of the connected device.
•	[Audio Input Mapping] : Updates audio 
input mapping if there are new devices 
connected. 
5 Press  OK	 to 	 confirm 	 your 	 choice. 	
Note
 •The connected devices must be connected 
through HDMI and switched on.
3 Make sure that there is nothing between 
the speakers and the microphone to block 
the sound, and make sure that the room 
is quiet. For example, switch off your T V 
or radio, close doors and windows, and 
switch off the air conditioning. Don’t put the 
microphone on top of speaker.
4 Press  (Home ) on your home theater 
remote control, and select [Setup]  > 
[Audio]  > [360Sound Setup] .
5 Follow the onscreen instructions to set up 
the sound. 
 » Dur

ing the calibration, you hear a series 
of test tones from the speakers and the 
subwoofer. These sounds are normal - 
don’t change the volume or move the 
speakers, and be sure to keep quiet until 
the
	 calibration 	 finishes.
6 Af ter the auto calibration, disconnect the calibration microphone.
Set up surround sound manually
Your home theater has a calibration microphone that 
allows you to calibrate your speakers automatically. If 
your speakers are more than 5m (16 feet) away from 
the calibration microphone, you can still get the best 
surround sound by setting them up manually.
1 Connect your speakers and subwoofer as described in the Quick Star t. For the best 
surround sound, turn your rear speakers to 
face your listening position.
2 Press  (Home ) on your home theater 
remote control, and select [Setup]  > 
[Audio]  > [Speaker Setup] .
3 Enter the distance for each speaker, and 
then listen to the test tones and adjust the 
volume.
Set up network
1 Press  (Home ).
2 Select  [Setup], then press OK .
3 Select [Network], then press OK .
4 Select and adjust the following set tings:
•	[Network Installation] : Star ts wired 
(Ethernet) or wireless setup. Follow 
the instructions to set up the network 
connection.
EN
 
						

							23
•	[Sleep Timer] : Sets a sleep timer to 
switch the home theater to standby 
af ter
	 a 	 specific 	 time.
5 Press OK	 to 	 confirm 	 your 	 choice. 	
Note
 •If your preferred disc language is not available, 
you can select [Other] from the list and enter 
the 4-digit language code which can be found 
at the back of this manual. 
 •If you select a language that is not available 
on a disc, the home theater uses the default 
language of the disc.
Change advanced settings
1 Press  ( Home ).
2 Select  [Setup], then press OK .
3 Select [Advanced] , then press OK .
4 Select and adjust the following set tings:
•	[BD-Live Security]  : Restricts or allows 
access to BD-Live.
•	[Enhanced Audio]  : Enables or disables 
the audio post processing at the 
speaker output.
•	[Software Update]  : Selects to update 
sof tware from the network or from 
USB storage device.
•	[Clear memory]  : Clears local memor y, 
delete 	 the 	 BD-Live 	 files 	 that 	 you 	 previously	d

ownloaded. If using an USB storage 
device, the local storage folder is ‘BUDA’.
•	[Di vX® VOD Code]  : Displays the 
DivX VOD registration code for the 
home theater.
•	[Version Info.]  : Displays the sof tware 
version for the home theater.
•	[Restore default settings]  : Resets the 
home theater to the default set tings 
programmed at the factor y.
5 Press  OK	 to 	 confirm 	 your 	 choice.
Note
 •You cannot restrict internet access on 
commercial Blu-ray discs. 
 •Before you purchase DivX videos and play them 
on the home theater, register the home theater 
on w w w.div x.com using the DivX VOD code.
 •You cannot reset parental control set ting to its 
default value.
Multiview
On Philips 21:9 Cinema TV (model 
58PFL9955H/12), you can watch two video 
sources side by side. The sources can be:
•	video from your home theater,
•	TV broadcasts, and
•	N e t T V.
For information about how to set up multi-view, 
see your TV user manual.
Change preference settings
1 Press  ( Home ).
2 Select  [Setup], then press OK .
3 Select [Preference] , then press OK .
4 Select and adjust the following set tings:
•	[Menu language]  : Selects the  
on-screen display menu language.
•	[Audio]  : Selects audio language for video.
•	[Subtitle]  : Selects subtitle language for 
video.
•	[Disc Menu]  : Selects menu language 
for video disc.
•	[Parental Control]  : Restricts access to 
discs that are recorded with ratings.  
To play all discs irrespective of the 
rating, select level ‘8’.
•	[Screen Saver]  : Enables or disables 
screen saver mode. If enabled, 
the screen enters idle mode af ter 
10
  minutes of inactivity (for example, 
in
  pause or stop mode).
•	[Auto Subtitle Shift] : Enables or 
disables shift subtitle. If enabled, 
it adjusts the subtitle position 
automatically 	 to 	 fit 	 the 	 T V 	 screen.
•	[Change Password] : Sets or changes 
a PIN code to play a restricted disc. 
Enter ‘ 0000’ if you do not have a PIN 
or if you have forgot ten your PIN.
•	[Display Panel]  : Changes the 
brightness of the display panel.
•	[Auto St andby]  : Enables or disables 
auto standby. If enabled, the home 
theater switches to standby af ter 
30
  minutes of inactivity (for example, 
in pause or stop mode).
•	[VCD PBC]  : Displays or skips the 
content menu for VCD and SVCD discs.
English
EN
 
						

							24
Update software from a USB
1 Check for the latest sof tware version on www.philips.com/suppor t.
•	Search for your model and click on 
‘software and drivers’.
2 Create a folder named ‘UPG’ in the root director y of your USB storage device.
3 Download the sof tware into the ‘\UPG’ folder of the USB storage device.
4 Unzip the sof tware in the ‘\UPG’ folder.
5 Connect the USB storage device to the home theater.
6 Press  (Home ) and select [Setup] .
7 Select [Advanced]  > [Software Update]  > 
[USB] .
8 Follow the instructions on the T V to 
confirm 	 the 	 update.
 »When complete

, the home theater 
automatically switches off and restar ts.
•	If not, disconnect the power cord for a 
few seconds and then reconnect it.
Caution
 •Do not turn off the power or remove the USB 
storage device when the sof tware update is in 
progress because you might damage the home 
theater.
6 Update softwa re
To check for new updates, compare the current 
software version of your home theater with the 
latest software version (if available) on the Philips 
web site.
Check software version
1 Press  (Home ).
2 Select  [Setup], then press OK .
3 Select [Advanced]  > [Version Info.] , then 
press OK .
 »The software v

ersion is displayed.
Update software from the 
network
1 Prepare the internet connection (see ‘Connect to a computer network and the 
Internet’ on page 10).
2 Press  (Home ) and select [Setup] .
3 Select [Advanced]  > [Software Update]  > 
[Network] . 
 »If an upgr

ade media is detected, you are 
prompted to star t or cancel the update. 
4	 Follow	the	instruction	on	the	T V	to	confirm	t he update.
 » When complete

, the home theater 
automatically switches off and restar ts.
•	If not, disconnect the power cord for a 
few seconds and then reconnect it.
Note
 •If the home theater is unable to connect to the 
Philips ser ver, press  ( Home ), select [Setup]  >  
[Network]  > [Network Installation]  to set up 
the network.
EN
 
						

							25
7 Product specifications
Note
 •Specification	and	design	are	subject	to	change	without notice.
Region code
The type plate on the back or bottom of the 
home theater shows which regions it suppor ts
 
Playback media
 • A

VCHD, BD-RE, BD-Video, DVD-Video, 
DVD+R /+RW, DVD -R /-RW, DVD+R /-R 
DL, CD-R /CD-RW, Audio CD, Video CD/
SVCD,
	 Picture 	 files, 	 MP3 	 media, 	 WMA 	
m

edia, DivX (Ultra)/DivX Plus HD media, 
USB storage device
File Format
 • A

udio: .mp3, .wma, .wav
 •V

ideo: .avi, .div x, .mp4, .mk v, .wmv
 •P

icture: .jpg, .gif, .png
Amplifier
 • T

otal output power : 800W RMS 
 •F

requency response: 40 Hz-20 kHz / ±3dB
 •S

ignal-to-noise ratio: > 65 dB (CCIR) / 
(A-weighted)
Count ry DVD   BD
Europe ,  
Unit ed Ki ngdom
Ko rea
 La tin Amer ica
 Aust ralia ,  
New Ze aland
 Russia , India
 China
AA
AA
CC
CC
Asia Pacific, Taiwan,
Update electronic user manual
1 Check the current version of the electronic 
user manual installed in your home theater 
(see ‘Check sof tware version’ on page 24). 
2 Inser t a USB storage device into your PC .
3 In your web browser, navigate to w w w.philips.com/suppor t, 	 and 	 find 	 your 	 product.
4 Click on ‘Sof tware and drivers’ in the lef t panel, and then locate the ‘Electronic 
Manual’. The electronic user manual is 
compressed into a *.zip archive. 
5	 If	the	*.zip	file	at	the	Philips	Suppor t	website	i s 	 a 	 later 	 version 	 than 	 the 	 file 	 in 	 your 	 home 	
t

heater, 	 download 	 the 	 file 	 in 	 the 	 root 	
d

irector y of your USB storage device.
6	 Unzip	the	downloaded	file	in	the	root	director y of the USB storage device.
 »A

	 file 	 named 	
‘
 HTSxxxxeDFU.zip’ is 
extracted in the ‘\UPG’ folder of your 
USB storage device, ‘xxxx’ being the 
model number of your home theater. 
7 Disconnect the USB storage device from  the PC , and connect it to the home theater.
8 Press  (Home ).
•	Ensure that there is no disc inside 
the disc compar tment of your home 
theater and it is closed.
9 Press  [3], [3] , [8]  on the remote control.
 » Software update star

ts. When complete, 
the home theater automatically switches 
off and restar ts.
10 When complete, disconnect the USB  storage device from the home theater.
Caution
 •Do not turn off the power or remove the USB 
storage device during the update.
 •If power failure occurs during the update, 
do 	 not 	 remove 	 the 	 USB 	 flash 	 drive 	 from 	 the 	
h

ome theater. The home theater continues the 
update as soon as the power is restored.
 •If an error occurs during the update, retr y 
the procedure. If the error reoccurs, contact 
Philips Consumer Care.
English
EN
 
						

							26
Subwoofer
 •I

mpedance: 4 ohm
 •S

peaker drivers: 165 mm (6. 5”) woofer
 •F

requency response: 40 Hz-150 Hz
 •D

imensions ( WxHxD): 196 x 397 x 342 (mm)
 •W

eight: 6.4 kg
 •C

able leng th: 3 m
Speakers 
 • S

ystem: full range satellite
 •S

peaker impedance: 4 ohm (center),  
6 ohm (Front/Rear)
 • S

peaker drivers: 
•	Center : 2 x 2. 5” woofer + 1”  
soft-dome tweeter
•	Front /Rear : 2 x 2. 5” full range + 2. 5” 
woofer + 1” sof t-dome tweeter
 •F

requency response: 150 Hz-20 kHz
 • D

imensions (WxHxD):
•	Center : 435 x 85 x 111 (mm)
•	Front /Rear : 99 x 247 x 117 (mm)
 • We

ight : 
•	Center : 1.67 kg
•	Front /Rear : 1.17 kg/each
 • C

able length: 
•	Center : 2 m
•	Front: 3 m
•	Rear : 10 m
Laser Specification
 • L

aser Type (Diode): InGaN/AIGaN (BD), 
AIGaInP (DVD/CD)
 • W

ave leng th: 405 +5nm/-5nm (BD),  
655 +5nm/-10nm (DVD),  
790 +10 nm/-10 nm (CD)
 • O

utput power (Max. ratings):  
20mW (BD), 6mW (DVD), 7mW (CD)
 • I

nput sensitivity:
•	AUX1, AUX2: 400 mV
•	MP3 LINK: 150 mV
Video
 • S

ignal system: PAL / NTSC
 • C

omponent video output: 480i/576i, 
480p/576p, 720p, 1080i
 • H

DMI output: 480i/576i, 480p/576p, 720p, 
1080i, 1080p, 1080p24
Audio
 • S

/PDIF Digital audio input:
•	Coaxial: IEC 60958-3
•	Optical: TOSL I N K
 • S

ampling frequency:
•	MP3: 32 kHz, 44.1 kHz, 48 kHz
•	WMA: 44.1 kHz, 48 kHz
 • Con

stant bit rate:
•	MP3: 112 kbps - 320 kbps
•	WMA: 48 kbps - 192 kbps
Radio
 • T

uning range: 
•	Europe/China:  
FM 87. 5-108 MHz (50 kHz)
•	Asia	Pacific/Russia/Latin	America/India:	F M 87. 5-108 MHz (50/100kHz)
 • S

ignal-to-noise ratio: FM 55 dB
 • F

requency response:  
FM 60 Hz-12. 5 kHz / ±3dB
USB
 • Co

mpatibility: Hi-Speed USB (2.0)
 • C

lass suppor t: UMS (USB Mass  
Storage Class)
 • F

ile system: NTFS, FAT16, FAT32
 • M

aximum memor y suppor t: < 160GB
Main Unit
 • P

ower supply: 
•	Europe/China: 220 -240V, ~50 Hz; 
•	Latin	America/Asia	Pacific:	1 10-127V/220-240V, ~50-60Hz; 
•	Russia/India: 220 -240V, ~50Hz 
 • P

ower consumption: 125 W
 • S

tandby 	 power 	 consumption: 	 ≤ 	 0.22 	 W 	
 
• D

imensions ( WxHxD): 437 x 75 x 342 
(m m)
 • W

eight: 4. 5 kg
EN
 
						

							27
Sound
No sound. •En
sure that the audio cables are connected 
and select the correct input source (for 
example, 
 SOURCE  / AUDIO SOURCE ) 
for the device you want to play.
No sound on HDMI connection.
 • Y

ou might not hear any sound if the 
connected device is not HDCP (High-
bandwidth Digital Content Protection) 
compliant or only DVI compatible. Use an 
analog or digital audio connection.
 • E

nsure that the [HDM I Audio]  is enabled.
No sound from TV program.
 • Con

nect an audio cable from the audio 
input on the home theater to the audio 
output on the T V, then press 
 SOURCE  / 
AUDIO SOURCE  repeatedly to select the 
correct audio source.
Distorted sound or echo.
 • E

nsure that the T V volume is muted or set 
to minimum if you are playing audio through 
the home theater.
Audio and video are not synchronized.
 • 1

) Press 
 SOUND SETTINGS  /   
( Sound OPTIONS ) . 2) Press the 
Navigation buttons  (left/right) repeatedly 
until AUDIO SYNC  is displayed, then  
press OK . 3) Press the Navigation buttons  
(up/down) to sync the audio with the video.
Cannot calibrate the speakers by using the 
calibration microphone.
 • E

nsure that the speakers, subwoofer, and 
calibration microphone are connected as 
described in the Quick Star t.
 • T

r y a different position for the speakers, 
and then calibrate the speakers again.
 • E

nsure that you follow all the steps for auto 
calibration (see ‘Set up surround sound 
automatically’ on page 21).
 • I

f you cannot calibrate the speakers 
automatically, or are unhappy with the 
automatic set tings, set up the speakers 
manually (see ‘Set up surround sound 
manually’ on page 22).
Play
Disc cannot be played.  • C
lean the disc.
 •En

sure that the home theater suppor ts the 
disc
	 (see 	 ‘Product 	 specifications’ 	 on 	 page 	 25).
8 Troubleshooting
Warning
 •Risk of electric shock . Never remove the 
casing of the product. 
To keep the warranty valid, never tr y to repair the 
product yourself. 
If you have problems using this product, check the 
following points before you request ser vice. If you 
still have a problem, register your product and get 
suppor t at www.philips.com/welcome. 
If you contact Philips, you will be asked for the model 
and serial number of your product. The model 
number and serial number are on the back or 
bottom of your product. Write the numbers here: 
Model No. __________________________
Serial No. ___________________________
Main unit
The buttons on this home theater do not work. •D
isconnect the home theater from the 
power outlet for a few minutes, then 
reconnect. 
Picture
No picture. • E
nsure that the T V is switched to the 
correct source for the home theater.
No picture on HDMI connection.
 • C

hange the HDMI video set ting or wait for 
15 seconds for auto recover.
 • C

heck if the HDMI cable is faulty. Replace 
with a new HDMI cable.
No picture on the Component (Y Pb Pr) 
connection.
 • I

f the HDMI video connection is set to 
[Auto]  or [10 8 0 p/24Hz] , there is no video 
output through the component connection. 
Change the HDMI video set ting or remove 
the HDMI connection.
No high-definition video signal on the TV.
 • E

nsure 	 that 	 the 	 disc 	 contains 	 high-definition 	
v

ideo.
 •E

nsure 	 that 	 the 	 T V 	 suppor ts 	 high-definition 	
v

ideo.
English
EN
 
						

							28
Cannot see pictures from my iPod/iPhone on the TV. •C
onnect a yellow composite cable from the 
dock to the T V.
 • S

witch the T V to the AV/ V I D E O  source 
(corresponding to the yellow composite cable).
 • P

ress P L AY  on the iPod or iPhone to star t 
the slideshow.
The audio is interrupted when I play music from 
my iPod or iPhone in the docking station.
 • E

nsure that you have installed the latest 
firmware
	 on 	 your 	 iPod 	 or 	 iPhone. 	 For 	 more 	
i

nformation, refer to the suppor t website of 
your iPod or iPhone.
My 3D video plays in 2D mode.
 • E

nsure that your home theater is connected 
to your 3D T V through HDMI.
 • E

nsure that your disc is a Blu-ray 3D disc.
 •E

nsure that the [Blu-ray 3D video] set ting 
is turned on (see ‘Change video set tings’ on 
page 20).
I see black video on my TV screen.
 • E

nsure that your home theater is connected 
to the T V through HDMI.
 • S

witch to the correct HDMI source on your T V.
I cannot download the video from the online 
video store.
 • E

nsure that your home theater is connected 
to the T V through HDMI.
 • E

nsure that the SD card is in place and 
formatted.
 • E

nsure that the SD memor y card has 
enough memor y to download the video, 
and is of type SDHC Class 6.
 • E

nsure that you have paid for the video and 
are within the rental period.
 • Che

ck the network connection (see 
‘Connect to a computer network and the 
Internet’ on page 10).
 • Con

tact the online video store for more 
help.
Network
Wireless network not found or distorted. • E
nsure that the wireless network is not 
disturbed by the microwave ovens, dect 
phones or other Wi-Fi devices in your 
neighbourhood.
 • T

r y the wired network installation if the 
wireless network does not work properly 
(see ‘Set up network ’ on page 999). 
 • E

nsure that the home theater suppor ts the 
region code of the disc.
 • F

or DVD±RW or DVD±R , ensure that the 
disc
	
is
	
finalized.
	
DivX video files cannot be pla

yed.
 •
E

nsure
	
that
	
the
	
DivX
	
file
	
is
	
encoded
	
a

ccording
	
to
	
the
	
‘Home
	
Theater
	
Profile’
	
w

ith the DivX encoder.
 •
E

nsure
	
that
	
the
	
DivX
	
video
	
file
	
is
	
complete.
DivX subtitles do not display correctly.
 • E

nsure
	
that
	
the
	
subtitle
	
file
	
name
	
is
	
the
	
s

ame
	
as
	
the
	
movie
	
file
	
name.
 •
S

elect the correct character set: 1) Press 
 OPTIONS
 /  (OPTIONS ). 2) Select 
[Character Set] . 3) Select the suppor ted 
character set. 4) Press OK .
The contents of a USB storage device cannot be 
read.
 • E

nsure that the format of the USB storage 
device is compatible with the home theater 
(see
	
‘Product
	
specifications’ 	 on 	 page 	 25).
 •E

nsure that the USB storage device 
is
	
format ted
	
with
	
a 	 file 	 system 	 that 	 is 	
s

uppor ted by the home theater.
‘No entry’ or ‘x’ sign appears on the TV.
 • T

he operation is not possible.
EasyLink feature does not work.
 • E

nsure that the home theater is connected 
to a Philips brand EasyLink T V and that 
EasyLink is on.
I do not want my home theater to be switched 
on when I switch on my TV.
 • T

his is the correct behavior for Philips 
EasyLink (HDMI-CEC). To make the home 
theater work independently, switch off 
EasyLink.
I cannot access BD-Live features.
 • Che

ck the network connection (see 
‘Connect to a computer network and 
the Internet’ on page 10) or ensure that 
the network has been set up (see ‘Set up 
network ’ on page 10).
 • C

lear memor y storage. (see ‘Change 
advanced set tings’ on page 23)
 • E

nsure that the Blu-ray disc suppor ts BD-
Live feature.
The video (movies, photos, video clips, etc.) 
contents of the iPod/iPhone do not display on TV.
 • V

ideo and photo browsing is not suppor ted, 
you can only browse the video and photo 
contents on the iPod/iPhone itself.
EN