Philips Hts7520 User Manual

							31
   
 
 
 
Reinstall all the radio stations
 
 
 
 
1 Press  RADIO 
.
 
 
 
 
2  Press and hold  PROGRAM 
 for more than 
5 seconds.
   
 
 
All previously stored radio stations are    »
replaced.
  Note
 
Check the radio antenna connection if no   •
stereo signal is detected or less than 5 stations 
are detected during radio installation.
   
 
 
 
Search and store radio stations 
individually
   
 
 
1 Press  RADIO 
.
 
 
 
 
2 Press   
 /   
.
   
 
 
It star ts searching until a radio station    »
is detected.
   
 
 
 
 
3  Repeat step 2 until you tune to the radio 
station you wish to store.
   
 
 
To  ne tune the radio frequency,  • 
press  
   /   
.
 
 
 
 
 
 
4 Press  PROGRAM 
.
   
 
 
The preset station number blinks.   »
   
 
 
If no action is carried out within 20    »
seconds after the above step, it exits 
the preset mode.
   
 
 
 
 
5 Press   
 /  
 (or the  Numeric buttons 
) to 
select a preset number to store.
   
 
 
6 Press  PROGRAM 
 to con rm.
First time tuning
 
 
When you access radio mode for the  rst 
time, follow the instruction to install the radio 
stations. 
   
 
 
1 Press  RADIO 
.
   
 
 
’AUTO INSTALL ... PRESS PLAY’ is    »
displayed. 
   
 
 
 
 
2 Press   
 
 
( Play 
).
   
 
 
All detected radio stations are stored.   »
   
 
 
Once complete, it tunes to the  rst    »
preset radio station.
   
 
 
 
 
 
 
To stop auto tuning, press   • 
 
.
 
Note
 
This Home Theatre System can store up to a   •
maximum of 40 radio stations.
   
If auto installation is not activated or less 
  •
than 5 radio stations are stored, you will be 
prompted to install the radio stations again.
   
 
 
 
Listen to radio
 
 
 
 
1 Press  RADIO 
.
 
 
 
 
2  Use the remote control to control the 
radio. 
  Button  Action
 
  
 
 /  
Selects a preset radio station.
   
 
 
 /  
Tunes the radio frequency up or 
down.
   
 
Press and hold this button to 
erase the current radio station 
from the preset list.
   
The preset number for    •
other radio stations remain 
unchanged.
  Note
 
If the FM radio station transmits RDS (Radio   •
Data System) data, the name of the radio 
station is displayed.
EN
 
						

							32
   
Option   
Description
 
 
5 CH 
STEREO  Enhance the stereo channel 
output by duplicating the sound 
output to the centre and rear 
speakers. Ideal for par ty music.
   
MULTI-
CHANNEL/
DPLII  Multi-channel surround output: 
DTS, Dolby TrueHD and Dolby 
Pro Logic II.
   
STEREO 
Stereo sound from two front 
speakers.
  Note
 
This product also contains the capability to   •
decode 5.1 DTS -Digital Surround.
 
 
 
 
 
 
Select preset sound
 
 
Select prede ned sound modes to suit your 
video or music.
   
  
 
 
 
 
1 Press  SOUND MODE 
 repeatedly to 
cycle through the available sound modes.
  Sound mode  Description
 
 
ACTION 
 / 
  ROCK  Enhanced low and high-range. 
Ideal for action movies and 
rock or pop music.
   
DRAMA 
 
 / 
   
JAZZ  Clear mid and high-range. Ideal 
for drama movies and jazz 
music.
   
CONCERT 
/ 
  CLASSIC  Neutral sound. Ideal for live 
concer ts and classical music.
   
SPORTS 
Moderate mid-range and 
surround effects for clear 
vocals and the atmosphere of a 
live spor t venue.
   
 
 
 
 
 
 
 
6 Adjust sound
 
 
 
 
Control the volume
 
 
 
 
1 Press   
 
 +/- 
 to increase or decrease the 
volume.
   
 
 
To mute, press   • 
 
.
   
 
 
To restore the volume, press   • 
 
 again 
or press  
   
 + 
.
 
 
 
 
 
 
 
 
 
Change treble and bass
 
 
Change the high frequency (treble) or low 
frequency (bass) settings of the Home Theatre 
System to suit your video or music.
   
 
 
 
 
 
1 Press  TREBLE 
 or  BASS 
.
 
 
 
 
2  Within  ve seconds, press   
 
 +/- 
 to 
increase or decrease treble or bass.
   
 
 
 
 
 
Select surround sound
 
 
Experience an immersive audio experience with 
surround sound modes.
   
  
 
 
 
 
1 Press  SURR. SOUND 
 repeatedly to 
select the best surround output that’s 
available on the disc.
EN
 
						

							33
[Audio] 
   
Selects the default audio language for disc play.
 
 
  
 
 
 
[Subtitle] 
   
Selects the default subtitle language for disc 
play.
   
  
 
 
 
[Disc Menu] 
   
Selects the language for the disc menu. 
 
Note
 
If the language you have set is not available on   •
the disc, the disc uses its own default language.
   
For some discs, the subtitle/audio language can 
  •
only be changed from the disc menu. 
 
 
  
 
 
 
 
 
[TV Display] 
   
Selects one of the following display formats 
which the disc can suppor t.
   
 
 
 
 
 
  • [4:3 Panscan] 
 – For 4:3 screen T V: full-
height display with the trimmed sides.
   
 
 
  • [4:3 Let terbox] 
 – For 4:3 screen T V: 
wide-screen display with black bars on 
the top and bottom of the screen.
   
 
 
  • [16:9 Widescreen] 
 – For wide-screen T V: 
display ratio 16:9.
   
 
 
  
 
 
 
 
 
4:3 Letter Box (LB) 4:3 Pan Scan (PS)
16:9 (Wide Screen)
   
 
 
 
 
7 Adjust settings
 
 
You can customise various kinds of settings as 
you prefer. Refer to the following instructions to 
navigate through the setup menus.
  Note
 
You cannot change a set ting that is greyed out.  •
 
 
 
 
 
Video Setup
 
 
 
 
1 Press   
.
 
 
 
 
2 Select  [Settings] 
, then press  OK 
.
 
 
 
 
3 Select  [Video Setup] 
, then press   
 
 
.
 
 
 
 
 
 
 
4  Select an option, then press  OK 
.
 
 
 
 
5  Select a setting, then press  OK 
.
   
 
 
To return to the previous menu,  • 
press  
   
 BACK 
.
   
 
 
To exit the menu, press   • 
 
.
 
Note
 
See the explanations of the above options in   •
the following pages. 
 
 
 
  
 
 
 
 
 
  Video Setup
Advanced Setup Audio Setup
Preference Setup
EasyLink Setup
SubtitleAudio
Disc Menu
TV Display
HDMI Video
HDMI Deep Color
Component Video
Picture SettingsOffEnglish
English
16:9 Widescreen
Auto
Auto
480i/576i
Standard
EN
 
						

							34
   
   
 
 
 
 
[Picture Settings] 
   
Selects a prede ned set of picture colour 
settings.
   
 
 
  • [Standard] 
 – Original colour setting.
   
 
 
  • [Vivid] 
 – Vibrant colour setting.
   
 
 
  • [Cool] 
 - Sof t colour setting.
   
 
 
  • [Action] 
 – Sharp colour setting. It 
enhances the details in the dark areas. 
Ideal for action movies.
   
 
 
  • [Animation] 
 – Contrast colour setting. 
Ideal for animated pictures.
   
 
 
  
 
 
 
 
 
[Black Level] 
   
Improves black colour contrast. 
   
 
 
  • [Normal] 
 - Standard black level.
   
 
 
  • [Enhanced] 
 - Enhances black level.
 
 
 
 
 
 
 
 
Audio Setup
 
 
 
 
1 Press   
.
 
 
 
 
2 Select  [Settings] 
, then press  OK 
.
 
 
 
 
3 Select  [Audio Setup] 
, then press   
 
 
.
 
 
 
 
 
 
 
4  Select an option, then press  OK 
.
 
 
 
 
5  Select a setting, then press  OK 
.
   
 
 
To return to the previous menu,  • 
press  
   
 BACK 
.
   
 
 
To exit the menu, press   • 
 
.
 
Note
 
See the explanations of the above options in   •
the following pages.
HDMI Audio Night Mode
Speaker Setup Video Setup
Advanced Setup Audio Setup
Preference Setup
EasyLink SetupOff
Auto
[HDMI Video] 
   
Selects the HDMI video output resolution 
that is compatible with your T V display 
capability.
   
 
 
  • [Auto] 
 - Detects and selects the best 
suppor ted video resolution automatically.
   
 
 
  • [Native] 
 - Sets to original video 
resolution.
   
 
 
  • [48 0 i/576i] 
 
,  
 
[48 0 p/576p] 
 
,  
 
[720p] 
 
,  
 
[10 8 0i] 
 
, 
   
[10 8 0p] 
 
,  
 
[10 8 0 p/24Hz] 
 - Selects a video 
resolution setting that is best suppor ted 
by the T V. See the T V manual for details.
  Note
 
If the set ting is not compatible with your T V, a   •
blank screen appears. Wait for 15 seconds for 
auto recover or press  HDMI 
 repeatedly until 
the picture appears.
   
  
 
 
 
 
 
[HDMI Deep Colour] 
   
This feature is available only when the display 
device is connected by a HDMI cable, and 
when it suppor ts the deep colour feature.
   
 
 
  • [Auto] 
 - Switches on automatically if the 
connected display device suppor ts HDMI 
deep colour.
   
 
 
  • [On] 
 - Enjoys vivid images in over a billion 
colours on Deep Colour enabled T V. 
Outputs 12 bit colour that reduces the 
posterisation effect.
   
 
 
  • [Of f ] 
 - Outputs standard 8 bit colour.
 
 
 
 
  
 
 
 
 
 
[Component Video] 
   
Selects the Component video output 
resolution that is compatible with the TV 
display capability.
   
 
 
  • [48 0 i/576i] 
 
,  
 
[48 0 p/576p] 
 
,  
 
[720p] 
 
,  
 
[10 8 0i] 
 
 
-  
Selects a video resolution setting that 
is best suppor ted by the T V. See the T V 
manual for details.
  Note
 
If the set ting is not compatible with the T V, a   •
blank screen appears. Wait for 15 seconds for 
auto recovery.
EN
 
						

							35
  Tip
 
The test tone is emit ted from the speaker   •
while adjusting the volume level. 
   
Allow 1 ms set ting for ever y 30 cm distance 
  •
between the speaker and the listening position. 
 
 
 
 
 
 
Preference Setup
 
 
 
 
1 Press   
.
 
 
 
 
2 Select  [Settings] 
, then press  OK 
.
 
 
 
 
3 Select  [Preference Setup] 
, then press   
 
 
.
 
 
 
 
 
 
 
4  Select an option, then press  OK 
.
 
 
 
 
5  Select a setting, then press  OK 
.
   
 
 
To return to the previous menu,  • 
press  
   
 BACK 
.
   
 
 
To exit the menu, press   • 
 
.
 
Note
 
See the explanations of the above options in   •
the following pages.
 
 
 
  
 
 
 
 
 
[OSD Language] 
   
Selects the default on-screen menu language.
 
Note
 
If this product is connected to a HDMI CEC   •
compliant T V using a HDMI cable, it switches 
automatically to the same menu display 
language as per your T V set ting.
 
Video Setup
Advanced Setup Audio Setup
Preference Setup
EasyLink SetupOSD Language
Parental Control
Screen Saver
Display Panel
Auto Standby
PBC Change PINEnglish
On
100%
On
On
Sleep Timer
OffOff
   
 
  
 
 
 
 
 
[Night Mode] 
   
Makes the loud sound level sof ter and the 
sof t sound level louder so that you can watch 
the disc at a low volume, without disturbing 
others.
   
 
 
  • [On] 
 – For quiet viewing at night.
   
 
 
  • [Of f ] 
 – For surround sound with a full 
dynamic range.
  Note
 
Applicable only to Dolby encoded DVD-video   •
or BD-video.
 
 
  
 
 
 
 
 
[HDMI Audio] 
   
Selects the HDMI audio output when you 
connect this Home Theatre System and the 
T V/audio device with a HDMI cable.
   
 
 
  • [As Source] 
– The audio format is not 
conver ted. A secondar y audio track on a 
Blu-ray disc might not be available.
   
 
 
  • [Auto] 
 – Detects and selects the best 
suppor ted audio format automatically.
   
 
 
  • [Of f ] 
 - Disables audio from the T V.
 
 
 
 
  
 
 
 
 
 
[Speaker Setup] 
   
Optimises the surround output for the 
connected speaker system.
  Option   Description
 
 
[Speaker 
Delay]  Sets the delay time 
for the centre or rear 
speakers if they are 
placed closer to the 
listening position, so that 
the sound output from 
all speakers reaches the 
listening position at the 
same time.
   
[Speaker 
Vo lu m e]  Sets the volume level 
of each speaker and 
subwoofer to get the 
ideal audio balance.
EN
 
						

							36
[Display Panel] 
   
Selects the brightness level of the front panel 
display.
   
 
 
  • [10 0%] 
 - Brightest
   
 
 
  • [70%] 
 - Medium 
   
 
 
  • [4 0%] 
 - Dimmest
 
 
 
 
  
 
 
 
 
 
[Auto St andby] 
   
Turns off or turns on standby switching mode. 
It is an energy saving feature.
   
 
 
  • [On] 
 - Switches to standby af ter 30 
minutes of inactivity (for example, in 
pause or stop mode).
   
 
 
  • [Of f ] 
 - Disables auto standby mode. 
 
 
 
 
  
 
 
 
 
 
[PBC] 
   
Turns off or on the content menu of VCDs/
SVCDs with PBC (playback control) feature.
   
 
 
  • [On] 
 - Displays the index menu when you 
load a disc to play.
   
 
 
  • [Of f ] 
 - Skips the menu and star ts play 
from the  rst title.
   
 
 
  
 
 
 
 
 
[Sleep Timer] 
   
Switches to standby automatically af ter a 
delay.
   
 
 
  • [Of f ] 
 – Disables the sleep timer.
   
 
 
  • [15 Minutes] 
, [30 Minutes] 
,  [45 Minutes] 
, 
  [60 Minutes] 
 – Selects a delay.
   
 
 
 
 
 
 
 
 
  
 
 
 
 
 
[Parental Control] 
   
Restricts access to discs that are unsuitable 
for children. These types of discs must be 
recorded with ratings.
   
To access, enter your last set password or 
‘ 0000 
’ using the keyboard on the T V.
 
Note
 
Rated discs above the level you set in    •[Parental 
Control] 
 require a password to be played. 
   
The ratings are countr y-dependent. To allow 
  •
all discs to play, select ‘ 8 
’ for DVD-video and 
BD-Video.
   
Some discs have ratings printed on them but 
  •
are not recorded with ratings. This function 
has no effect on such discs.
   
  
 
 
 
 
 
[Screen Saver] 
   
Turns off or on the screen saver mode. Helps 
to protect the T V screen from being damaged 
due to over exposure to a static image for too 
long. 
   
 
 
  • [On] 
 - Sets the screen saver to appear 
af ter 10 mins of inactivity (for example, in 
pause or stop mode)
   
 
 
  • [Of f ] 
 - Disables screen saver mode.
 
 
 
 
  
 
 
 
 
 
[Change PIN] 
   
Sets or changes the password.
 
1) Press the  Numeric buttons 
 to enter the 
password or your last set password. If you 
forget the password, enter ‘ 0000 
’, then press 
  OK 
.
   
2) Enter the new password.
   
3) Enter the same password again.
   
4) Move to  [Con rm] 
 in the menu and press 
  OK 
.
 
 
  
 
 
 
 
 
EN
 
						

							37
[One Touch Play] 
   
When you press  PLAY 
 on the remote control, 
the T V (if it suppor ts one-touch play) and 
the Home Theatre System will be turned on. 
Disc play star ts if there is a disc in the Home 
Theatre System and the T V automatically 
switches to the correct channel to show the 
video content. 
   
 
 
  • [On] 
 - Enables one-touch play feature.
   
 
 
  • [Of f ] 
 - Disables one-touch play feature.
 
 
 
 
  
 
 
 
 
 
[One Touch Standby] 
   
When you press and hold  
 
 ( Standby 
) on the 
remote control, this Home Theatre System 
and all the connected HDMI CEC devices (if 
they suppor t one-touch standby) switch to 
standby mode simultaneously. 
   
 
 
  • [On] 
 - Enables one-touch standby 
feature.
   
 
 
  • [Of f ] 
 - Disables one-touch standby 
feature.
  Note
 
When    •[Of f ] 
 is selected, the Home Theatre 
System cannot be switched to standby by a 
remote control from the T V or other devices.
   
  
 
 
 
 
 
[System Audio Control] 
   
When you play a device where the audio 
output is routed to this Home Theatre 
System, this Home Theatre System 
switches to the corresponding audio source 
automatically.
   
 
 
  • [On] 
 - Enables system audio control 
feature. Then proceed to  [Audio Input 
Mapping] 
 to scan and map all the 
connected devices.
   
 
 
  • [Of f ] 
 - Disables system audio control 
feature.
   
 
 
  
EasyLink Setup
 
 
 
 
1 Press   
.
 
 
 
 
2 Select  [Settings] 
, then press  OK 
.
 
 
 
 
3 Select  [EasyLink Setup] 
, then press   
 
 
.
 
 
 
 
 
 
 
4  Select an option, then press  OK 
.
 
 
 
 
5  Select a setting, then press  OK 
.
   
 
 
To return to the previous menu,  • 
press  
   
 BACK 
.
   
 
 
To exit the menu, press   • 
 
.
 
Note
 
See the explanations of the above options in   •
the following pages.
 
 
 
  
 
 
 
 
 
[EasyLink] 
   
Your product suppor ts Philips Easylink, which 
uses the HDMI CEC (Consumer Electronics 
Control) protocol. EasyLink-compliant devices 
that are connected through HDMI connectors 
can be controlled by a single remote control. 
   
 
 
  • [On] 
 - Enables EasyLink features.
   
 
 
  • [Of f ] 
 - Disables EasyLink features.
 
 
 
 
  
 
 
 
 
 
Video Setup
Advanced Setup Audio Setup
Preference Setup
EasyLink SetupOne Touch Play EasyLink
One Touch StandbyOn
On
System Audio ControlOff
Audio Input MappingOn
EN
 
						

							38
   
 
 
 
[BD-Live Security] 
   
You can restrict Internet access when BD-
R /RE disc is used.
   
 
 
  • [On] 
 
 -  
Internet access is prohibited for all 
BD-Live contents.
   
 
 
  • [Of f ] 
- Internet access is permitted for all 
BD-Live contents.
   
 
 
  
 
 
 
 
 
[Network] 
   
Sets up a connection to an ex ternal network 
for sof tware download and BD-Live 
applications. It guides you through a step-by-
step network installation procedure. 
  Note
 
There is more detailed description available,   •
see ‘Get ting Star ted’ > ‘Set up network ’. 
 
 
  
 
 
 
 
 
[Software Download] 
   
Updates the sof tware of this product (if a 
newer version is available on Philips website) 
to enhance playability. 
   
 
 
  • [USB] 
 - Downloads sof tware via USB.
   
 
 
  • [Network] 
 - Downloads sof tware via 
network. 
  Note
 
There is more detailed description available,   •
see ‘Additional Information’ > ‘Upgrade 
Software’. 
   
  
 
 
 
 
 
[Clear Local Storage] 
   
Deletes the content of the BD-Live storage 
folder on the USB drive.
  Note
 
Local storage is a folder (BUDA) located on   •
the connected USB device.
 
 
   
 
 
 
 
  
 
 
 
 
 
[Audio Input Mapping] 
   
Maps the connection between other devices 
and the audio input jacks of this Home 
Theatre System. Only the detected devices 
will be displayed for mapping. 
  Note
 
You need to enable the    •[System Audio 
Control] 
 before you can map the audio input.
 
 
 
 
 
 
Advanced Setup
 
 
 
 
1 Press   
.
 
 
 
 
2 Select  [Settings] 
, then press  OK 
.
 
 
 
 
3 Select  [Advanced Setup] 
, then press   
 
 
.
 
 
 
 
 
 
 
4  Select an option, then press  OK 
.
 
 
 
 
5  Select a setting, then press  OK 
.
   
 
 
To return to the previous menu,  • 
press  
   
 BACK 
.
   
 
 
To exit the menu, press   • 
 
.
 
Note
 
See the explanations of the above options in   •
the following pages.
 
 
 
  
Video Setup
Advanced SetupBD Live Security
Network
Software Download
Clear Local Storage
DivX® VOD Code
Version Info.
Restore Factory Settings Audio Setup
Preference Setup
EasyLink SetupOff
EN
 
						

							39
   
 
 
 
[DivX® VOD Code] 
   
Displays the DivX® registration code.
 
Tip
 
Enter this product’s DivX registration code   •
when you rent or purchase a video from w w w.
div x.com/vod. The DivX videos rented or 
purchased through the DivX® VOD ( Video 
On Demand) ser vice can be played only on 
the device to which it is registered.
   
  
 
 
 
 
 
[Version Info.] 
   
Displays the sof tware version of this Home 
Theatre System. 
  Tip
 
This information is required when you want to   •
 nd out if a newer sof tware version is available 
at the Philips website that you may download 
and install on this Home Theatre System. 
   
  
 
 
 
 
 
[Restore Factory Settings] 
   
Resets all the settings of this product to 
factor y default, except for  [Parental Control] 
 
setting.
EN
 
						

							40
   
 
 
5  Inser t the USB  ash drive to this Home 
Theatre System.
   
 
 
6  At Home menu, select  [Settings] 
 
>  [Advanced Setup] 
 >  [Software 
Download] 
 >  [USB] 
.
 
 
 
 
7  Follow the instructions on the T V to 
con rm update operation.
   
 
 
Once software update is complete,    »
this Home Theatre System turns off to 
standby automatically.
   
 
 
 
 
8  Disconnect the power cord for a few 
seconds and connect again to reboot the 
Home Theatre System.
  Note
 
Do not turn off the power or remove the USB   •
when sof tware updating is in progress as it 
may damage the Home Theatre System.
   
 
 
 
 
 
8 Update software
 
 
To check for new updates, compare the current 
software version of your home theatre with 
the latest software version (if available) on the 
Philips website.
   
 
 
 
1 Press   
.
 
 
 
 
2 Select  [Settings] 
, then press  OK 
.
 
 
 
 
3 Select  [Advanced Setup] 
 >  [Version 
Info.] 
, then press  OK 
.
 
 
 
 
 
 
 
Update software via network
 
 
 
 
1  Prepare the network connection, see 
chapter ‘Getting Star ted’ > ‘Set up 
network ’ for detailed information.
   
 
 
2  At Home menu, select  [Settings] 
 
>  [Advanced Setup] 
 >  [Software 
Download] 
 >  [Network] 
. 
 
 
 
 
3  Follow the instructions on the T V to 
con rm update operation.
   
 
 
Once software update is complete,    »
this Home Theatre System turns off to 
standby automatically.
   
 
 
 
 
4  Disconnect the power cord for a few 
seconds and connect again to reboot the 
Home Theatre System. 
   
 
 
 
 
 
Update software via USB
 
 
 
 
1  Go to the w w w.philips.com/suppor t to 
check the latest sof tware version available 
for this Home Theatre System.
   
 
 
2  Create a folder named ‘UPG’ in the root 
of a USB  ash drive.
   
 
 
3  Download the sof tware onto the ‘UPG’ 
folder of the USB  ash drive.
   
 
 
4  Unzip the downloaded sof tware in the 
‘UPG’ folder.
EN