Philips Hts7520 User Manual

							11
   
 
 
 
  
 
 
 
 
This speakers placement is for HTS7520 only.
   
Different set of speakers for HTS7500 and 
HTS7540. (see ‘Speci cations’ > ‘Speakers’).
   
  
 
 
 
 
 
 
1  Place this Home Theatre System near to 
the TV
   
 
 
2  Place the speakers system at normal 
listening ear-level and directly parallel to 
the listening area.
   
 
 
3  Place the subwoofer at the corner of the 
room or at least 1 metre (3 feet) away 
from the T V.
  Tip
 
To avoid magnetic inter ference or unwanted   •
noise, never place this home theatre too close 
to any radiation devices.
   
 
 
 
 
Connect video cables
 
 
Connect this Home Theatre System to a TV to 
view disc play. Select the best video connection 
that the TV can suppor t.
   
 
 
 
Option 1: Connect to the HDMI jack (for  • 
a HDMI, DVI or HDCP-compliant T V ). 
   
 
 
Option 2: Connect to the component  • 
video jacks (for a standard T V or 
progressive scan T V ).
   
 
 
Option 3: Connect to the video (CVBS)  • 
jack (for a standard T V ).
SUBWOOFER
REAR
RIGHT
REAR
LEFT
FRONT
RIGHT
FRONT
LEFT
CENTER
   
 
 
 
 
 
3 Connect
 
 
Make the following connections to use your 
Home Theatre System. For a comprehensive 
interactive guide, see www.connectivityguide.
philips.com.
   
  
 
 
 
Basic connections: 
   
 
 
Video • 
   
 
 
Speakers and subwoofer • 
   
 
 
Power • 
   
 
 
 
 
Optional connections: 
   
 
 
Radio antenna • 
   
 
 
Audio • 
   
 
 
Audio from T V • 
   
 
 
Audio from cable box /recorder/ • 
game console
   
 
 
 
 
Other devices • 
   
 
 
Por table media player • 
   
 
 
USB device • 
   
 
 
 
 
L AN (Network) • 
 
Note
 
Refer to the type plate at the back or bot tom   •
of the product for identi cation and supply 
ratings.
   
Before you make or change any connections, 
  •
ensure that all devices are disconnected from 
the socket.
   
 
 
 
 
Place the product
 
 
 
 
Place the product where it cannot be  • 
pushed, pulled over or knocked down. 
Do not place it in an enclosed cabinet.
   
 
 
Make sure that you have full access to the  • 
power cord for easy disconnection of the 
product from the power supply.
EN
 
						

							12
   
 
 
 
Option 2: Connect to the component 
video jack
   
 
 
 
 
 
1  Connect the component video cable 
(not supplied) to the  Y Pb Pr 
 jacks on 
this Home Theatre System and the 
COMPONENT VIDEO input jacks on the 
TV.
  Note
 
The component video input jack on the T V   •
might be labelled as  Y Pb Pr 
,  Y Cb Cr  
or  YUV 
.
   
This type of connection provides good picture 
  •
quality.
VIDEO OUT
PbPrY
PbPrY
 
Note
 
You must connect this Home Theatre System   •
directly to a T V.
 
 
 
 
 
Option 1: Connect to the HDMI jack
 
 
  
 
 
 
 
1  Connect the HDMI cable to the  HDMI 
OUT 
 jack on this Home Theatre System 
and the HDMI input jack on the T V. 
  Tip
 
If the T V has a DVI connector only, connect via   •
a HDMI/DVI adapter. Connect an audio cable 
for sound output.
   
You can optimise the video output. Press 
  •
 
HDMI 
 repeatedly to select the best resolution 
the T V can suppor t. 
   
To play back the digital video images of a BD-
  •
video or DVD-video via an HDMI connection, 
it is necessary that both the Home Theatre 
System and the display device suppor t a 
copyright protection system called HDCP 
(high-bandwidth digital content protection 
system). 
   
This type of connection provides the best 
  •
picture quality.
HDMI OUT
HDMI IN
EN
 
						

							13
Connect speaker cables to 
speakers
   
 
 
 
 
 
 
1  Match the colour of the cable to the 
terminal tab.
   
 
 
2  Press the terminal tab down and inser t 
the stripped end of the speaker cable, 
then release.
   
 
 
 
 
 
 
Connect speaker to speaker 
stand
   
 
For the speakers of HTS7540 and the front 
speakers of HTS7520 only
   
 
 
 
 
 
 
 
1  Attach the speakers to the speaker stands 
and secure the position with screws.
   
 
 
 
 
 
 
 
 
 
 
 
Option 3: Connect to the Video 
(CVBS) jack
   
 
 
 
 
 
1  Connect a composite video cable (not 
supplied) to the  VIDEO 
 jack on this 
Home Theatre System and the VIDEO 
input jack on the T V.
  Note
 
The video input jack on the T V might be   •
labelled as  A/V IN 
,  VIDEO IN 
,  COMPOSITE 
 
or  BASEBAND 
. 
   
This type of connection provides standard 
  •
picture quality.
 
 
 
 
 
 
VIDEO
VIDEO OUT
VIDEO IN
EN
 
						

							14
For HTS7520
   
 
 
  
 
 
 
 
 
 
1  Connect the speakers and subwoofer to 
the matching jacks on this Home Theatre 
System.
  Note
 
Ensure that the colours of the plugs and jacks   •
are matched.
Connect speakers and 
subwoofer
   
 
For HTS7500 and HTS7540 (HTS7540 has a 
different set of speakers)
   
 
 
  
 
 
 
 
EN
 
						

							15
Connect audio cables/other 
devices
   
Route the audio from other devices to this 
Home Theatre System to enjoy audio play with 
multi-channel surround capabilities.
   
 
 
Connect audio to TV
 
 
(also used for EasyLink control)
 
 
  
 
 
 
 
1  Connect the audio cables (not supplied) 
to the  AUDIO IN-AUX1 
 jacks on this 
Home Theatre System and the AUDIO 
output jacks on the T V. 
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘AUX1’ is displayed on the 
display panel.
   
 
 
 
AUDIO OUT
AUX 1
AUDIO IN
   
 
 
 
 
Connect radio antenna
 
 
 
  
 
 
 
 
 
 
1  Connect the FM antenna to the  FM75 
 
 
 jack on this Home Theatre System 
(for some models, this cable is already 
connected).
   
 
 
2  Ex tend the FM antenna and  x its ends to 
the wall.
  Tip
 
For bet ter FM stereo reception, connect to an   •
ex ternal FM antenna.
 
 
 
 
 
 
FM (75 Ω) 
ANTENNA
EN
 
						

							16
   
 
Connect to coaxial jack 
 
 
  
 
 
 
 
1  Connect a coaxial cable (not supplied) 
to the  DIGITAL-IN-COAXIAL 
 jack 
on this Home Theatre System and the 
COA XIAL /DIGITAL output jack on the 
device.
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘COA X IN’ is displayed on the 
display panel.
   
  
 
 
 
COAXIAL
DIGITAL OUT
COAXIAL
DIGITAL IN
Connect audio from a cable box, 
recorder or games console
   
You can choose to connect to analogue 
or digital jacks depending on the device 
capabilities.
   
  
 
 
  
  
 
 
Connect to analogue jacks 
 
 
  
 
 
 
 
1  Connect the audio cables (not supplied) 
to the  AUDIO IN-AUX2 
 jacks on this 
Home Theatre System and the AUDIO 
output jacks on the device. 
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘AUX2’ is displayed on the 
display panel.
   
  
AUDIO OUT
AUX 2
AUDIO IN
EN
 
						

							17
   
 
 
 
Connect portable media player
 
 
  
 
 
 
 
1  Connect a 3. 5 mm stereo audio cable 
(not supplied) to the  MP3 LINK 
 jack 
on this Home Theatre System and the 
phone jack on the por table media player 
(such as MP3 player).
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘MP3 LINK’ is displayed on the 
display panel. 
   
 
 
 
Connect USB device
 
 
  
 
 
 
 
1  Connect the USB device to   
 
USB 
 jack 
on this Home Theatre System.
  Note
 
This Home Theatre System can only play/view   •
MP3, WMA, DivX (Ultra) or JPEG  les that are 
stored on such devices.
   
Press  
  •USB 
 to access the content and play the 
 les.
   
 
 
 
 
MP3
Connect to optical jack 
 
 
  
 
 
 
 
1  Connect an optical cable (not supplied) 
to the  DIGITAL-IN 
- OPTICAL  
jack 
on this Home Theatre System and the 
OPTICAL /SPDIF output jack on the 
device.
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘OPTI IN’ is displayed on the 
display panel.
OPTICAL
DIGITAL IN
DIGITAL OUTOPTICAL
OPTICAL
EN
 
						

							18
Connect LAN
   
Connect this Home Theatre System to the 
network for software updates and enjoy BD-
Live applications.
   
 
  
 
 
 
 
 
 
1  Connect the network cable (not 
supplied) to the  LAN 
 jack on this Home 
Theatre System and the L AN jack on the 
broadband modem or router.
  Note
 
Use an RJ45 straight cable. Do not use a   •
crossover cable.
   
Internet access to Philips website for sof tware 
  •
updates may not be allowed, depending on 
the router you use or the Internet Ser vice 
Provider’s policy. Contact your Internet 
Ser vice Provider for more information. 
   
 
 
 
 
Connect power cord
 
Warning
 
Risk of product damage! Ensure that the   •
power supply voltage corresponds to the 
voltage printed on the back or the underside 
of the product.
   
 
 
1  Connect the power cord to the socket 
when all the required connections are 
made.
   
 
 
This product is ready to be set up for    »
use.
LAN
BROADBAND
EN
 
						

							19
  Button  Action
 
  
 
 /  
Move up or down
   
 /  
Move lef t or right
   
OK 
Con rm a selection
 
 
 
Enter numbers
   
 
Access to the Home 
menu.
   
 
 
 
 
Find the correct viewing 
channel
   
 
 
1 Press   
 ( Standby 
) to turn on this 
product.
   
 
 
2 Press  DISC 
 to switch to disc mode.
 
 
 
 
3  Turn on the T V and switch to the correct 
video-in channel in one of the following 
ways:
   
 
 
Go to the lowest channel on your  • 
T V, then press the Channel Down 
button until you see the Philips or 
the Home menu screen.
   
 
 
Press the   • 
 
 
 SOURCE 
 button 
repeatedly on the remote control of 
your T V. 
  Tip
 
The video-in channel is between the lowest   •
and highest channels and may be called 
FRONT, A / V IN, VIDEO, HDMI etc. See the 
T V user manual on how to select the correct 
input on the T V.
   
 
 
 
 
 
 
 
 
 
 
 
 
 
4 Get started
 
 
 
 
Insert the remote control 
batteries
   
 
  
 
 
 
 
 
 
1  On the back of the remote control, slide 
the batter y cover to remove it.
   
 
 
2  Inser t the 2 supplied batteries (A A A). Be 
sure the + and - ends of the batteries line 
up with the markings inside the case.
   
 
 
3  Slide the cover back into position.
 
Note
 
Do not mix bat teries (old and new or carbon   •
and alkaline, etc.).
   
Remove bat teries if they are exhausted or if 
  •
the remote control is not to be used for a long 
time.
   
Bat teries contain chemical substances, they 
  •
should be disposed of properly.
 
 
 
 
 
Navigate through the menu
 
 
 
 
1  Point the remote control directly at the 
remote sensor on the product and select 
the desired function.
   
 
 
2  Press the following buttons on the 
remote control to navigate through the 
on-screen menus.
EN
 
						

							20
  Tip
 
You can set the default language for DVD disc,   •
see (‘Adjust set tings’ > ‘ Video Setup’ >  [Disc 
Menu] 
).
 
 
 
 
 
 
Set up network
 
 
Follow the steps below to help you set up the 
network connection for software updates and 
enjoy BD-Live applications.
   
 
  
 
 
 
 
 
 
1  Connect the home theatre to a 
broadband modem or router.
   
 
 
2  Turn on your T V and switch to the 
correct source for the home theatre.
   
 
 
3 Press   
, select  [Settings] 
 then press  OK 
.
 
 
 
 
4 Select  [Advanced Setup] 
 >  [Network] 
 > 
  [Next] 
.
 
 
 
 
5 Press  OK 
.
   
 
 
The home theatre connects to the    »
Internet. If connection fails, select 
  [Retry] 
 then press  OK 
. 
 
 
 
 
 
 
6 Select  [Finish] 
 then press  OK 
 to exit.
 
Note
 
Loading BD-Live content from the Internet   •
may take some time, depending on the  le size 
and the speed of the Internet connection.
   
 
 
LAN
BROADBAND
Use the Home menu
 
 
 
  
 
 
Press   
 ( Home menu 
).
   
 
 
Select   • [Play Disc] 
 to star t disc play. 
   
 
 
Select   • [USB] 
 to view the USB contents.
   
 
 
Select   • [Settings] 
 to access the setup 
menu. 
   
 
 
 
 
 
 
Select menu display language
 
Note
 
Skip this set ting if this product is connected   •
to a HDMI CEC compliant T V. It switches 
automatically to the same OSD menu language 
as per your T V set ting.
   
 
 
 
1  In the Home menu, select  [Settings] 
 and 
press  OK 
.
 
 
 
 
2 Select  [Preference Setup] 
, then press   
 
 
.
 
 
 
 
3 Select  [OSD Language] 
, then press  OK 
.
 
 
  
 
 
 
 
The language options are different  • 
depending on your countr y or 
region. It may not correspond to the 
illustration shown here.
   
 
 
 
 
4 Press   
  
 to select a language, then press 
  OK 
.
Play DiscUSBSettings
Parental Control OSD Language
Screen Saver
Display Panel
Auto Standby
PBC Change PIN
Sleep TimerNederlands Français
Deutsch
Italiano
Es pañol
Svenska
Português
English
EN