Philips Hts6120 User Manual

							11
   
 
 
 
Option 3: Connect to the Video 
(CVBS) jack
   
  
 
 
 
 
1  Connect a composite video cable to the 
  VIDEO OUT 
 jack on this Home Theater 
System and the VIDEO input jack on the 
TV.
  Note
 
The video input jack on the T V might be   •
labeled as A / V IN, VIDEO IN, COMPOSITE or 
BASEBAND. 
   
This type of connection provides standard 
  •
picture quality.
VIDEO OUT
VIDEO IN
 
Tip
 
If the T V has a DVI connection only, connect   •
via a HDMI/DVI adaptor. Connect an audio 
cable for sound output.
   
You can optimize the video output. (see ‘Adjust 
  •
set tings’ > ‘ Video setup’ >  [HDMI Setup] 
).
   
This type of connection provides the best 
  •
picture quality.
 
 
 
 
 
Option 2: Connect to the component 
video jack
   
 
 
 
 
 
1  Connect the component video cable 
(not supplied) to the  Y Pb Pr 
 jacks on 
this Home Theater System and the 
COMPONENT VIDEO input jacks on the 
TV.
   
 
 
If a progressive scan T V is used, you  • 
may turn on the progressive scan 
mode. (see ‘Get star ted’ > ‘Turn on 
Progressive Scan’).
  Note
 
The component video input jack on the T V   •
might be labeled as Y Pb/Cb Pr/Cr or YUV. 
   
This type of connection provides good picture 
  •
quality.
YPbPr
COMPONENT
VIDEO OUT
Connect
English
EN
 
						

							12
   
 
 
 
 
 
 
Connect radio antenna
 
 
 
  
 
 
 
 
 
 
1  Connect the FM antenna to the  FM75 
  
 
jack on the subwoofer (for some models, 
this cable is already connected).
   
 
 
2  Ex tend the FM antenna and  x its ends to 
the wall.
  Tip
 
For bet ter FM stereo reception, connect to an   •
ex ternal FM antenna.
FM ANTENNA
(75 Ω)
   
 
 
 
 
Connect subwoofer
 
 
 
  
 
 
 
 
 
 
1  Unwind the subwoofer’s interconnect 
cable at  TO MAIN UNIT 
.
 
 
 
 
2  Connect the white end of 
the interconnect cable to the 
  LOUDSPEAKERS 
 jack on this Home 
Theater System.
   
 
 
3  Connect the gray end of the interconnect 
cable to the  TO SUBWOOFER 
 jack on 
this Home Theater System.
TO MAIN UNIT
TO SUBWOOFER
LOUDSPEAKERS
EN
 
						

							13
   
 
 
 
Connect audio from cable box/
recorder/game console
   
You can choose to connect to analog or digital 
jack depending on the device capabilities.
   
  
 
 
 
Connect to analog jacks 
 
 
 
 
 
 
 
1  Connect the audio cables (not supplied) 
to the  AUDIO IN-AUX2 
 or  AUX3 
 jacks 
on the subwoofer and the AUDIO output 
jacks on the device. 
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘AUX2 INPUT’ or ‘AUX3 
INPUT’ is displayed on the display panel. 
   
  
AUX 2
AUDIO INAUDIO OUT
   
 
 
 
 
Connect audio cables/other 
devices
   
Route the audio from other devices to this 
Home Theater System to enjoy audio play with 
multi-channel surround capabilities.
   
 
 
Connect audio from TV
 
 
(also used for EasyLink control)
 
 
 
 
 
 
 
1  Connect the audio cables (not supplied) 
to the  AUDIO IN-AUX1 
 jacks on the 
Home Theater System and the AUDIO 
output jacks on the T V. 
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘AUX1 INPUT’ is displayed on 
the display panel. 
AUX 1
AUDIO IN
AUDIO OUT
English
EN
Connect
 
						

							14
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘OPTICAL INPUT’ is displayed 
on the display panel.
   
 
 
 
Connect portable media player
 
 
  
 
 
 
 
1  Connect a 3. 5mm stereo audio cable (not 
supplied) to the  MP3 LINK 
 jack on this 
Home Theater System and the phone 
jack on the por table media player (such as 
MP3 player).
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘MP3 LINK’ is displayed on the 
display panel. 
MP3
   
 
Connect to coaxial jack  
 
 
 
 
 
 
 
1  Connect a coaxial cable (not supplied) to 
the  COA XIAL DIGITAL-IN 
 jack on the 
subwoofer and the COA XIAL /DIGITAL 
output jack on the device.
  Note
 
To listen to the audio output from this   •
connection, press  AUDIO SOURCE 
 
repeatedly until ‘COA XIAL INPUT’ is 
displayed on the display panel.
   
  
 
 
 
Connect to optical jack 
 
 
 
 
 
 
 
1  Connect an optical cable (not supplied) 
to the  OPTICAL DIGITAL-IN 
 jack on 
the subwoofer and the OPTICAL /SPDIF 
output jack on the device.
DIGITAL INCOAXIAL
DIGITAL OUT
DIGITAL INOPTICAL
DIGITAL OUT
EN
 
						

							15
  Note
 
To listen to the audio output from this   •
connection, press  iPod DOCK 
.
 
 
 
 
 
 
Connect power cord
 
Warning
 
Risk of product damage! Ensure that the   •
power supply voltage corresponds to the 
voltage printed on the back or underside of 
the subwoofer. Set the voltage selector (if any) 
correctly before you connect the subwoofer 
to the power outlet.
   
 
 
1  Connect the power cord to the power 
outlet when all the required connections 
are done.
   
 
 
The Home Theater System is ready to    »
be set up for use.
   
 
 
 
Connect USB device
 
 
  
 
 
 
 
1  Connect the USB device to   
 
 
 
USB 
 jack 
on this Home Theater System.
  Note
 
This Home Theater System can only play/view   •
MP3, WMA, DivX (Ultra) or JPEG  les that are 
stored on such devices.
   
Press  
  •USB 
 to access the content and play the 
 les.
   
 
 
 
Connect iPod docking station
 
 
  
 
 
 
 
1  Connect the iPod docking station 
(optional accessor y - not supplied) to 
  FOR iPod DOCK 
 jack on this Home 
Theater System.
   
 
 
2  To view videos/photos from iPod, 
connect a composite video cable from 
this docking station to the T V and switch 
the T V to the correct viewing channel.
VIDEO INVIDEO IN
English
EN
Connect
 
						

							16
   
  
 
 
 
 
5  Position the supplied bracket on the wall, 
drill the screw holes and inser t the rubber 
wall plugs (not supplied) into the holes.
   
 
 
To mount this Home Theater System  • 
below the T V, leave at least 4 inches 
of space between the T V and the 
bracket.
   
  
 
 
 
 
 
 
 
 
 
Mount the Home Theater 
System
  Caution
 
Risk of personal injur y and damage to the   •
product. Allow only quali ed persons to 
mount the product.
   
 
 
1  Ensure all the required cables are 
connected to this Home Theater System 
and close the rear cover.
   
 
 
2  Attach the supplied knobs to the rear of 
this Home Theater System.
   
  
 
 
 
 
3  Turn this Home Theater System over so 
that its bottom faces up.
   
 
 
4  Remove the rubber feet by pushing it 
towards the back of this Home Theater 
System. Repeat the step to remove the 
other rubber feet.
EN
 
						

							17
   
 
 
 
 
6  Secure the bracket onto the wall with 
screws (not supplied).
   
  
 
 
 
 
7  Hook this Home Theater System  rmly 
onto the mounted bracket. Slide the 
knobs through the key holes to lock into 
position.
   
 
 
  
English
EN
Connect
 
						

							18
   
 
 
 
Control a play source
 
 
 
 
1 Press   
 
RADIO 
,  USB 
 or  DISC 
 button to 
select the source you wish to control.
   
 
 
2  Select the desired function (for example  
 
,   
). 
 
 
 
 
 
 
 
Navigate through the menu
 
 
  
 
 
 
 
1  Point the remote control directly at the 
remote sensor on the product and select 
the desired function.
   
 
 
2  Press the following buttons on the 
remote control to navigate through the 
on-screen menus.
  Button  Action
 
  
  
Move up or down
   
 
Move lef t or right
   
OK 
Con rm a selection
 
 
 
Enter numbers
 
 
 
 
 
 
4 Get started
 
 
 
 
Insert the remote control 
batteries
   
 
  
 
 
 
 
 
 
1  Slide the batter y cover off the back of the 
remote control.
   
 
 
2  Inser t the 2 supplied batteries (A A A). Be 
sure the + and - ends of the batteries line 
up with the markings inside the case.
   
 
 
3  Slide the cover back into position.
 
Note
 
Do not mix bat teries (old and new or carbon   •
and alkaline, etc.).
   
Remove bat teries if they are exhausted or if 
  •
the remote control is not to be used for a long 
time.
   
Bat teries contain chemical substances, they 
  •
should be disposed of properly.
EN
 
						

							19
   
 
 
 
Start Ambisound  setup
 
 
When you turn on this Home Theater System 
for the  rst time, follow the instructions on the 
TV to complete the Ambisound setup in order 
to obtain the best possible surround sound 
effect.
  Note
 
Before you star t, ensure that you have made   •
all the required connections.
   
Complete the Ambisound setup before you 
  •
inser t a disc to play.
 
 
 
 
1 Press  DISC 
 to switch to disc mode.
 
 
 
 
2  Turn on the T V and switch it to the 
correct video-in channel. 
   
 
 
    »[OSD Language] 
 screen is displayed.
 
 
  
 
 
 
 
 
 
3  Select a language for on-screen menu 
display, then press  
  . 
   
 
 
A welcome message is displayed.   »
 
 
 
 
 
 
4 Press   
 to continue.
   
 
 
A message on product orientation is    »
displayed.
   
 
 
 
 
5 Press   
 to continue.
   
 
 
    »[Room Acoustics] 
 screen is displayed.
Please choose your language:
Continue
OSD Language
Stop: Exit
English
Ó×i
						

							20
   
  
 
 
 
 
 
 
9  Select the distance between the listening 
position and the speakers, then press  
  .
 
 
 
 
10  The speaker setting is complete, press   
 
to exit.
   
 
 
  
 
 
This Home Theater System is now ready for 
use.
  Tip
 
You can change the menu display language   •
(see ‘Adjust set tings’ > ‘Preferences’ >  [OSD 
Language] 
).
   
If you connect this Home Theater System to 
  •
HDMI CEC compliant T V using HDMI cable, 
it switches automatically to the menu display 
language as per your T V set ting.
Select the distance between your listening position 
and the SoundBar system:
Select
Listening Position
Back
Change
Near (< 2m / 6.5ft)
Far (> 3m / 9.8ft) Default (2-3m / 6.5-9.8ft)
   
  
 
 
 
 
 
 
6  Select the condition of the room, then 
press  
  .
   
 
 
    »[Room Placement] 
 screen is displayed.
 
 
  
 
 
 
 
 
 
7  Select this Home Theater System 
placement in the room, then press  
  .
   
 
 
    »[Height] 
 screen is displayed.
 
 
  
 
 
 
 
 
 
8  Select the height of which this Home 
Theater System is placed, then press  
  .
   
 
 
    »[Listening Position] 
 screen is displayed.
Please select the type of walls that surround
your room:
Select
Room Acoustics
Back
Change
Soft  (Curtains, open space) Hard (Concrete, wood)
Select the Sound Bar system placement position 
in your room:
Select
Room Placement
Back
Change
Near the right wall Corner of room
Near the left wall Middle of room
Select the height at which your SoundBar system 
is placed:
Select
Height 
Back
Change
High (> 1.2m / 3.9ft)
Low (< 0.8m / 2.6ft) Default (0.8-1.2m / 2.6-3.9ft)
EN