Philips Hts3377 User Manual

							12
Option 1: Connect to the HDMI jack
   
 
 
 
 
 
1  Connect an HDMI cable (not supplied) 
to the  HDMI OUT 
 jack on this Home 
Theater System and the HDMI input jack 
on the TV.
  Note
 
If your device suppor ts HDMI CEC, you can control   •
compliant devices with a single remote control. (see 
‘Get star ted’ > ‘Use Philips EasyLink’).
  Tip
 
If the TV has a DVI connection only, connect via a   •
HDMI/DVI adaptor. Connect an audio cable for sound 
output.
   
You can optimize the video output. (see ‘Adjust settings’ 
  •
> ‘Video setup’ >  [HDMI Setup] 
).
   
This type of connection provides the best picture 
  •
quality.
 
 
 
 
 
HDMI OUT
HDMI IN
Connect video cables
 
 
Connect this Home Theater System to TV to 
view disc play. Select the best video connection 
that the TV can suppor t.
   
 
 
 
Option 1: Connect to the HDMI jack (for a  • 
HDMI, DVI or HDCP-compliant TV). 
   
 
 
Option 2: Connect to the component  • 
video jacks (for a standard TV or 
Progressive Scan TV).
   
 
 
Option 3: Connect to the video (CVBS)  • 
jack (for a standard TV).
  Note
 
You must connect this Home Theater System directly   •
to a TV.
 
 
 
 
 
EN
 
						

							13
Option 3: Connect to the Video 
(CVBS) jack
   
 
 
 
 
 
1  Connect a composite video cable to the 
  VIDEO 
 jack on this Home Theater System 
and the VIDEO input jack on the TV.
  Note
 
The video input jack on the TV might be labeled as A/V   •
IN, VIDEO IN, COMPOSITE or BASEBAND. 
   
This type of connection provides standard picture 
  •
quality.
 
 
 
 
 
 
VIDEO
VIDEO OUT
VIDEO IN
Option 2: Connect to the component 
video jack
   
 
 
 
 
 
1  Connect the component video cable 
(not supplied) to the  Y Pb Pr 
 jacks on 
this Home Theater System and the 
COMPONENT VIDEO input jacks on the 
TV.
   
 
 
If a progressive scan TV is used, you  • 
may turn on the progressive scan 
mode. (see ‘Get star ted’ > ‘Turn on 
Progressive Scan’).
  Note
 
The component video input jack on the TV might be   •
labeled as Y Pb/Cb Pr/Cr or YUV. 
   
This type of connection provides good picture quality.
  •
 
 
 
 
 
VIDEO OUT
PbPrY
PbPrY
EN
Connect
English
 
						

							14
   
 
 
 
 
 
 
Connect speakers and 
subwoofer
   
 
  
 
 
 
 
 
 
1  Connect the speakers and subwoofer to 
the matching jacks on the Home Theater 
System.
  Note
 
Ensure that the colors of the plugs and jacks are   •
matched.
 
 
 
 
 
 
Connect speaker cables to 
speakers
   
 
For the rear speakers only
 
 
 
 
 
 
 
 
 
1  Connect the speaker cables to the 
matching color jacks on the speakers (or 
speaker stands).
   
 
 
 
 
 
 
Connect speaker to speaker 
stand
   
 
For the rear speakers only
 
 
 
 
 
 
 
 
 
1  Attach the speakers to the speaker stands 
and secure the position with screws.
EN
 
						

							15
   
 
 
 
 
Connect audio cables/other 
devices
   
Route the audio from other devices to this 
Home Theater System to enjoy audio play with 
multi-channel surround capabilities.
   
 
 
Connect audio from TV
 
 
(also used for EasyLink control)
 
 
  
 
 
 
 
1  Connect the audio cables (not supplied) to 
the  AUDIO IN-AUX1 
 jacks on the Home 
Theater System and the AUDIO output 
jacks on the TV. 
  Note
 
To listen to the audio output from this connection,   •
press  AUDIO SOURCE 
 repeatedly until ‘AUX1’ is 
displayed on the display panel.
AUDIO OUT
AUX 1
AUDIO IN
Connect radio antenna
   
 
  
 
 
 
 
 
 
1  Connect the FM antenna to the  FM75 
  
 
jack on this Home Theater System 
(for some models, this cable is already 
connected).
   
 
 
2  Extend the FM antenna and  x its ends to 
the wall.
  Tip
 
For better FM stereo reception, connect to an external   •
FM antenna.
FM (75 Ω) 
ANTENNA
EN
Connect
English
 
						

							16
Connect to coaxial jack  
 
 
  
 
 
 
 
1  Connect a coaxial cable (not supplied) to 
the  COAXIAL DIGITAL-IN 
 jack on the 
Home Theater System and the COAXIAL/
DIGITAL output jack on the device.
  Note
 
To listen to the audio output from this connection,   •
press  AUDIO SOURCE 
 repeatedly until ‘COAX IN’ is 
displayed on the display panel.
   
 
Connect to optical jack 
 
 
  
 
 
 
 
1  Connect an optical cable (not supplied) 
to the  OPTICAL DIGITAL-IN 
 jack on the 
Home Theater System and the OPTICAL/
SPDIF output jack on the device.
COAXIAL
DIGITAL OUT
COAXIAL
DIGITAL IN
DIGITAL INOPTICAL
DIGITAL OUTOPTICAL
   
 
 
 
Connect audio from cable box/
recorder/game console
   
You can choose to connect to analog or digital 
jack depending on the device capabilities.
   
  
 
 
 
Connect to analog jacks 
 
 
  
 
 
 
 
1  Connect the audio cables (not supplied) to 
the  AUDIO IN-AUX2 
 jacks on the Home 
Theater System and the AUDIO output 
jacks on the device. 
  Note
 
To listen to the audio output from this connection,   •
press  AUDIO SOURCE 
 repeatedly until ‘AUX2’ is 
displayed on the display panel.
   
 
AUX 2
AUDIO OUT
AUX 2
AUDIO IN
EN
 
						

							17
Connect USB device
   
  
 
 
 
 
1  Connect the USB device to   
 
 
 
 USB 
 jack 
on this Home Theater System.
  Note
 
This Home Theater System can only play/view MP3,   •
WMA, DivX (Ultra) or JPEG  les that are stored on 
such devices.
   
Press  
  •USB 
 to access the content and play the  les.
 
 
 
 
 
Connect power cord
 
Warning
 
Risk of product damage! Ensure that the power supply   •
voltage corresponds to the voltage printed on the back 
or the underside of the Home Theater System.
   
 
 
1  Connect the power cord to the power 
outlet when all the required connections 
are done.
   
 
 
The Home Theater System is ready to    »
be set up for use.
  Note
 
To listen to the audio output from this connection,   •
press  AUDIO SOURCE 
 repeatedly until ‘OPTI IN’ is 
displayed on the display panel.
   
 
 
 
Connect portable media player
 
 
  
 
 
 
 
1  Connect a 3.5mm stereo audio cable (not 
supplied) to the  MP3 LINK 
 jack on this 
Home Theater System and the phone jack 
on the por table media player (such as MP3 
player).
  Note
 
To listen to the audio output from this connection,   •
press  AUDIO SOURCE 
 repeatedly until ‘MP3 LINK’ is 
displayed on the display panel. 
   
 
 
 
MP3
EN
Connect
English
 
						

							18
Control a play source
   
 
 
1 Press   
 
RADIO 
,  USB 
 or  DISC 
 button to 
select the source you wish to control.
   
 
 
2  Select the desired function (for example   
, 
 
  ). 
 
 
 
 
 
 
 
Navigate through the menu
 
 
  
 
 
 
 
1  Point the remote control directly at the 
remote sensor on the Home Theater 
System and select the desired function.
   
 
 
2  Press the following buttons on the remote 
control to navigate through the on-screen 
menus.
  Button  Action
 
  
  
Move up or down
   
 
  
Move left or right
   
OK 
Con rm a selection
 
 
 
Enter numbers
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4 Get started
 
 
 
 
Insert the remote control 
batteries
   
 
  
 
 
 
 
 
 
1  Slide the batter y cover off the back of the 
remote control.
   
 
 
2  Inser t the 2 supplied batteries (AAA). Be 
sure the + and - ends of the batteries line 
up with the markings inside the case.
   
 
 
3  Slide the cover back into position.
 
Note
 
Do not mix batteries (old and new or carbon and   •
alkaline, etc.).
   
Remove batteries if they are exhausted or if the 
  •
remote control is not to be used for a long time.
   
Batteries contain chemical substances, they should be 
  •
disposed off properly.
 
 
 
 
 
EN
 
						

							19
Select menu display language
  Note
 
Skip this setting if this Home Theater System is   •
connected to a HDMI CEC compliant TV. It switches 
automatically to the same OSD menu language as per 
your TV  setting.
   
 
  
 
 
 
 
 
 
1 Press  DISC 
.
 
 
 
 
2 Press   
 
 SETUP 
.
   
 
 
    »[General Setup] 
 menu is displayed.
 
 
 
 
 
 
3 Press   
.
 
 
 
 
4 Press   
  
 to select  [OSD Language] 
 in the 
menu, then press  
  .
   
 
 
The language options are different  • 
depending on your countr y or 
region. It may not correspond to the 
illustration shown here. 
   
 
 
 
 
5 Press   
  
 to select a language, then press 
  OK 
.
 
Tip
 
You can set the default language for DVD disc menu   •
(see ‘Adjust settings’ > ‘Preferences’ >  [Disc Menu] 
).
 
 
 
 
 
 
General Setup
Screen Saver Disc Lock EasyLink Setup
Display Dim
DivX(R) VOD Code Sleep Timer
Ó×i
						

							20
  Note
 
If a blank/distor ted screen is displayed, wait for 15   •
seconds for the auto recover.
   
If no picture displayed, turn off the progressive 
  •
scan mode as follows:  1) Press   
 to open the disc 
compar tment.  2) Press  
  .  3) Press  AUDIO SYNC 
.
 
 
 
 
 
 
8 Press   
 
 SETUP 
 to exit the menu. 
 
 
 
 
9  You can now turn on the progressive scan 
mode on the TV.
  Note
 
During play, when progressive scan mode is on for both   •
this Home Theater System and the TV, distor ted picture 
may display. Turn off the progressive scan feature on 
both this Home Theater System and the TV.
Turn on Progressive Scan
   
If the TV suppor ts progressive scan output, you 
can connect this Home Theater System and the 
TV using component video connection. (see 
‘Connect video cables’ > ‘Option 2: Connect to 
the component video jack’).
   
 
  
 
 
 
 
 
 
1  Turn on the TV and ensure that the TV 
progressive scan mode is deactivated (see 
the TV user manual).
   
 
 
2  Switch the TV to the correct viewing 
channel for this Home Theater System.
   
 
 
3 Press  DISC 
.
 
 
 
 
4 Press   
 
 SETUP 
.
 
 
 
 
5 Press   
 to select  [Video Setup] 
 in the 
menu, then press  
  .
 
 
 
 
6 Select  [Progressive] 
 >  [On] 
, then press 
  OK 
.
   
 
 
A warning message is displayed.   »
 
 
 
 
 
 
7  To proceed, select  [Ok] 
 and press  OK 
.
   
 
 
The progressive setup is complete.   »
Video Setup
Picture Setting
Closed Caption HDMI Setup TV Display TV System
Screen Fit
ProgressiveOn
Off
EN
 
						

							21
   
 
 
2 Press   
  
 to change the volume level, then 
press  OK 
.
   
 
 
The test tone is emitted from the    »
speaker.
   
 
 
 
 
 
 
Repeat the above setting for other  • 
speakers until all the speakers output 
level sounds equally balance.
   
 
 
To exit the menu, press   • 
 
 
 SETUP 
.
 
 
  
 
 
 
 
 
To set the output delay time (center and rear 
speakers only) 
 
 
  
 
 
 
 
1 Select  [Speakers Delay] 
 in the menu, then 
press  
  .
 
 
  
 
 
 
 
2 Press   
  
 to set the delay time, then press 
  OK 
.
   
 
 
Repeat the above setting for other  • 
speakers until the sound output from 
different speakers reach the listening 
position at the same time. 
   
 
 
To exit the menu, press   • 
 
 
 SETUP 
.
 
Tip
 
Set a longer delay time if the center speaker or rear   •
speaker is closer to the listening position than the front 
speaker.
   
Allow 1ms setting for ever y 1 foot distance between 
  •
the speaker and the listening position.
Speakers Distance Setup
Center
Rear Left
Rear Right0MS
0MS
0MS
   
 
 
 
 
Change speaker settings
 
 
Ideally, the distance between listening position 
and all the speakers should be the same. If not, 
change the speaker settings based on their 
distance from the listening position to obtain 
the best possible surround sound.
   
 
  
 
 
 
 
 
 
1 Press  DISC 
.
 
 
 
 
2 Press   
 
 SETUP 
.
 
 
 
 
3 Press   
 to select  [Audio Setup] 
 in the 
menu, then press  
  .
   
 
 
If the speaker setup option is not  • 
accessible, press 
   twice before you 
press  
   
 SETUP 
. 
 
 
  
 
 
 
 
 
 
 
To set the speakers level  
 
  
 
 
 
 
1 Select  [Speakers Volume] 
 in the menu, 
then press  
  .
 
 
  
CD Upsampling Speakers Delay Speakers Volume
HDMI Audio
Audio Setup
Audio Sync
Speakers Volume Setup
Front Left
Front Right
Center
Subwoofer
Rear Left
Rear Right0dB
0dB
0dB
0dB
0dB
0dB
Get started
English
EN