Philips Bdl4631v User Manual

							User Manual BDL4631V/00 
 8 
 
Elements Name and Functions 
Control Panel 
 
        
POWER button () : To switch the power on/off.  
MUTE button : To switch the audio mute ON/OFF.  
INPUT  button : To  set  the function while OSD  menu is  on  or  to  toggle  switch  between [HDMI1], [HDMI2], [PC-A], [C VI], [VIDEO< S>] and [VIDEO] while OSD menu is off.  
PLUS (+) button : To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is off.  
MINUS (-) button : To decrease the adjustment while OSD menu is on, or to decrease the audio output level while the OSD menu is off. 
UP  ()  button :  To move the highlight bar up to adjust the selected item while OSD menu is on, or to activate the OSD menu when the OSD menu is off.    
DOWN  ()  button :To move the highlight bar down to adjust the selected item while OSD menu is on, or to activate the OSD menu when the OSD menu is off. 
EXIT button : To return to previous menu while OSD menu is on or to activate the OSD menu when the OSD menu is off.  
Remote  control  sensor  and  Power  indicator : To  receive  the IR signal  from  the  remote  control.  The  indicator  would  show green when the LCD monitor is active and would turn red when the LCD is POWER OFF.  While in the case of the system is in power save mode, it would show both  green  and  red.  When  SCHEDULE  is  enabled,  it would blink  green  and  glow  red.  If  the  indicator  blinks  red  ,  it  tells  that a  failure  is detected. 
Main Power Switch : To turn the main power on/off.  
NOTE: Keyboard Control  Lock  Mode This function completely disables  the access  to  all Keyboard Control functions.  To enable the keyboard  control lock,  press  both  of  “”  and  “” buttons and hold down continuously for  more  than  3  seconds.  To recover back  to the user  mode, press both of “” and “” and hold continuously for three 3 seconds.   
Buttons 
 
						

							                                         User Manual BDL4631V/00 
 
 9 
 
Terminal Panel 
                                                                                                             
  
 AUDIO IN 1, 2, 3  
To input audio signal from external equipment such as a computer, VCR or DVD player.  
 AUDIO OUT  
To output the audio signal from the AUDIO IN 1,2 and 3 jack.  
 EXTERNAL CONTROL (mini D-Sub 9 pin)  
This  is  for  serial  connection  when multiple BDL4631V monitors  are  connected. To  achieve  the  remote  control  through  RS232  command  (refer  to  the 
RS232 remote control user manual), connect the IN connector with the RS-232C OUT connector from the computer or a multi-connected BDL4631V 
monitor and connect the OUT connector with the RS-232C IN connector of BDL4631V monitor.  
 VIDEO IN/OUT  
VIDEO IN connector (BNC and RCA): To input a composite video signal.  Note that BNC and RCA are not available at the same time.  
VIDEO OUT connector (BNC): To output the composite video signal from VIDEO IN connector.  
S-VIDEO IN connector (MINI DIN 4 pin): To input the S-video (Y/C separate signal).  
 EXTERNAL SPEAKER TERMINAL  
To output the audio signal to external speakers from AUDIO IN 1, 2, 3 jack or HDMI.  
 AC IN connector  
To connect with the supplied power cord.  
 HDMI 1 IN  
To input digital RGB signals from a digital equipment or computer.  
* This connector does not support analog input. AUDIO is supported via HDMI. 
 HDMI 2 IN  
To input digital RGB signals from a digital equipment or computer. 
* This connector does not support analog input. AUDIO is supported via HDMI. 
 PC-A IN (mini D-Sub 15 pin) 
To input analog RGB signals from a computer or other RGB equipment. 
 RGB OUT (mini D-Sub 15 pin)  
To output the signal from PC-A IN. 
 CVI IN [Y, Pb/Cb, Pr/Cr] (BNC)  
To Connect an equipment such as a DVD player, HDTV device, or Laser disc player. 
 
						

							User Manual BDL4631V/00 
 10 
 
Remote Control 
     
  
 
  
 
  
 
  
 
  
 
  
 
  
 
  
 
  
 
  
 POWER button  
To turn the power on/off.  
If  LED  Power  Indicator  on  the  monitor  is  not lightening, then the remote control will not work.  
 
 SMART PICTURE button 
To select smart picture mode from [HIGHBRIGHT], [STANDARD],  
[sRGB], [CINEMA].   
HI GHBRI GHT: for moving image su ch as Vi deo 
STANDAR D: for images (Factory setting) 
sRGB: for text based images 
CINEMA: for movies. 
 PIP (Picture In Picture) button 
ON/OFF button: To turn PIP mode ON/OFF.  
INPUT button: To select the input signal for the sub-picture. 
CHANGE  button: To  exchange  between  the main  picture  and  sub-picture. 
Note:  
The  “PIP”  and  “POP”  modes  do  not work if the  screen  size  is “CUSTOM” or “REAL”. 
 CONTRAST button  
To start CONTRACT OSD selection, and then push + or - button to adjust the value. 
 
 DISPLAY button  
To turn on/off the setting information displayed on  the  right-up  corner of the screen. 
 
 MINUS button 
To decrease the adjustment with OS D menu.  
To move the sub-picture left when in “PIP” mode. 
 SET button 
To activate the setting with OSD menu.  
 AUTO ADJUST button 
To ex ec ute the AUTO ADJUST function.  
 MUTE button 
To turn the mute function on/off.  
 VIDEO SOURCE button  
To  set  the  video  source  by  toggle  selection from [HDMI1], [HDMI2], 
[PC-A], [CVI], [VIDE O] and [VIDEO]. 
 AUDIO SOURCE button  
To set the audio source by toggle selection from [AUDIO1] to [AUDIO2], 
[AUDIO3] and [HDMI]. 
Note 1: You cannot select the audio source for video source is set to 
[VIDE O] or [VIDEO].  
Note 2: [HDMI] is selectable only when the video source is [HDMI 1] or 
[HDMI 2]. 
 SIZE button 
To  select the picture size from [FULL], [NORMAL], [CUSTOM] , [DYNA M 
IC] and [REAL]. 
 BRIGHTNESS button 
To start the BRIGHTNESS OSD selection,  and  then  push  +  or  - 
button to adjust the value. 
 UP button  
To move the highlight bar up to adjust the selected item when OSD menu 
is on. 
To move the sub-picture up when in “PIP” mode. 
 MENU button 
To turn the OSD menu on/off. 
 PLUS button  
To increase the adjustment with OSD menu.  
 
To move the sub-picture right when in “PIP” mode. 
  
 EXIT button 
To turn to the previou s OSD menu. 
 DOWN button  
To  move  the  highlight bar  down to adjust the  selected  item when OSD 
menu is on. 
To move the sub-picture down when in “PIP” mode. 
 VOLUME UP button 
To increase the audio output level. 
 VOLUME DOWN button 
To decrease the audio output lev el.
 
   
						

							                                         User Manual BDL4631V/00 
 
 11 
Operating Range for the Remote 
Control 
Point the top of the remote control toward the LC D monitors remote 
sensor during button operation. 
Use the remote control within a distance of about 7 m/23 ft from the 
front of the LC D monitors remote control sen sor and within a 
horizontal and vertical angle 30° with a distance of about 3 m/10 ft. 
Handling the remote control 
* Do not subject to strong shock. 
* Do not allow water or other liquid to splash the remote control. 
If the remote control gets wet, wipe it dry immediately. 
* Avoid exposure to heat and steam. 
* Other than to install the batteries, do not open the remote 
control. 
  
  
 
  
 
  
 
  
 
  
 
  30° 30° 
 
 
            NOT E: 
The remote control system may not function when direct sunlight or 
strong illumination strikes the remote control sensor of the LC D monitor, 
or when there is an obstacle in the radiation path. 
  
 
  
 
  
 
  
 
  
 
  
 
  
   
 
  
						

							User Manual BDL4631V/00 
 12 
 
 
 
 
 
How to Mount or Attach Feet to the LCD Monitor 
 You can install the LCD monitor in one of the following two ways: 
 
Way 1: Attach and remove the optional feet 
 
How to install feet 
 
1.   Please turn the monitor off. 
2.    After inserting feet in guide block, fasten the thumbscrews on both sides of the monitor. 
 
NOTE: 
Install the feet with their longer portions directing to the front. 
 
 
                                                 Screws                         
    
 
  
      
  
 
 
                                                                                                                                            
 
 
                                
Optional Feet   In the upright position 
 
  
 How to remove the feet 
1.   Spread the protective sh eet on the flat surface. 
2.   Make the monitor lying on the protective sheet. 
3.   Remove screws using a screwdriver and place them in a safe place for reuse. 
 
Longer portions directs to the front 
  
						

							                                         User Manual BDL4631V/00 
 
 13 
 To avoid monitor from falling Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and damage. As  shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the monitor(BDL4631V:  approx. 34.6  kg).  Screw hooks  (commercially  available), of ring type  rather  than C-shaped  screw  hooks  (with  opening),  are recommended. 
 
 Caution:  Though the recommended prevention from falling is intended to lessen the probability of injury and damage, it doesn’t assure its effectiveness against any kind of earthquake or disaster.  Before moving the monitor, remove the rope that is securing the monitor.   
 
Way II: Mount the monitor on the wall 
Before mounting  the  monitor  to  the  wall, make  sure  that the  system  has  been  power-off  and  you  have obtain  a standard wall-mounting  kit (commercially available). Using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America is recommended.  
 
 
                                                                         Tabletop stand  1. Lay a protective  sheet  on  a  table,  which  was  wrapped  around  the  monitor  when  it  was  packaged,  beneath  the  screen  surface  so  as  not to  scratch the screen face. 2. This  device  cannot  be  used  or  installed  without  the  Tabletop  Stand  or  other  mounting  accessory.  Make  sure  all  these  stuffs  are  ready  for  wall-mount installation.  3.  Follow the instructions  that  come  with  the  base  mounting  kit. Failure  to  follow  correct  mounting  procedures  could  result  in  damage  to  the 
equipment or injury to the user or installer.  Product warranty does not cover damage caused by improper installation. 4. For  the wall-mounting  kit,  use  M6  mounting  screws  (having  a  length  10  mm  longer  than  the  thickness  of  the  mounting  bracket)  and  tighten  them securely. (Recommended torque: 470 - 635N•cm).   
 Caution: 
For preventing the monitor from falling.  Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of installation, refer to the instructions of the metal brackets.  To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the bracket manufacturer for installation location.  To lessen the risk of falling of the monitor, thread commercially available rope (having a load capacity at least 1960N (200kgf)) through the handles at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets.(Refer to the first paragraph of this page.) 
Protective Sheet 
Table Handles 
Screw Holes  
Screw hook 
Clamper Screw 
Rope 
* Clamper and Screw here is not supplied. 
 
						

							User Manual BDL4631V/00 
 14 
 
Ventilation Requirements for enclosure locating 
 To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.  
 
 
						

							                                         User Manual BDL4631V/00 
 
 15 
 
 
 
 
 
Setup Procedure 
 
1. Install the system on the right location  
C AUTI ON: 
THE LC D MONI TOR MUS T BE MOVED OR INSTALLED BY 
TWO OR MORE PERSONS. 
Failure to follow this caution may result in injury if the LC D 
monitor falls.  C AUTI ON: 
DO NOT ATTEMPT TO INSTALL THE LC D MONI TOR BY 
YOURSELF. 
The LC D display must be installed by a qualified technician. 
Contact your dealer for more information. 
 C AUTI ON: 
DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN, 
FACE UP, OR FACE DOWN. 
C AUTI ON: 
DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE 
EXPOSED TO DIRECT SUNLIGHT. 
Failure to follow this caution will result in display defects. 
 
IMPORTANT: 
Lay the protective sheet, which was wrapped around the LC D monitor 
when it was packaged, beneath the LC D monitor so as not to scratch the pan el. 
 
2. Install the remote control batteries 
The remote control is powered by 1.5V AAA batteries. To 
install or replace batteries: 
1.   Press and slide to open the cover. 
2.   Align the batteries according to the (+) and (–) indications inside 
the case. 
3.   Replac e the cover.  
 
C AUTI ON: 
Incorrect use of batteries can result in leaks or bursting. Be 
careful especially about the following points. 
•  Place “AAA” batteries matching the + and - signs on each battery 
to the + and - signs of the battery compartment. 
•  Do not mix battery types. 
•  Do not combine new batteries with used ones.   It causes shorter 
battery life or leakage of batteries. 
•  Remo v e dead batteries immediately to prev ent battery 
liquid from lea king into the battery compartment. Dont touch 
exposed battery acid, it cau se damage to your skin. 
NOTE: 
If you do not intend to use the Remote Control for a long period, 
remove the batteries.
3. Connect to external equipment 
•  To protect the connected equipment, turn off the main power 
before making connections. 
•  Please refer to section “Connectivity” P.18~P.22 for operations..   
4. Connect power cord 
•  The power outlet socket should be installed as near to the 
equipment as possible, and should be easily accessible. 
•  Fully insert the prongs into the power outlet socket. Loose 
connection may cause noise. 
NOTE: 
Please refer to “Safety Operation” section of this man ual for 
proper selection of AC power cord. 
 Cable belt Cable Holder 
  
 
  
 
  
 
  
 
  
 
  
       
  
5. Turn on the power of the 
attached external equipment 
Wh en connected with a computer, turn on the power of the computer 
first. 
 
6. Operate the attached external equipment 
Display the signal from the external equipment. 
 
7. Adjust the sound 
Make adjustments to lower or to rise the volume as required. 
 
8. Adjust the screen  
Make adjustments to the display position or settings if required. 
Use the Cable belt  to secure the  cables firmly. 
 
 
						

							User Manual BDL4631V/00 
 16 
 
 
 
 
9. Adjust the image  
Make adjustments to brightness or contrast if required.   
10. Recommended Adjustment 
To reduce the risk of “image persistence”, please adjust the 
following items based on the application being used. 
“P OWER SAVE”, “PANEL  SAVING”, “SIDE BORDER COLOR”, 
“DATE AND TIME”, “SCHEDULE”. 
 
 
11. To prevent the main power switch 
from being changed 
To prevent the possibility of main power switch being carelessly 
pushed, please attach the main switch cover (accessory) onto it. 
NOTE: 
With the main power switch cover in place, the main power switch 
can not be turned off. Remov e main power switch cover in order to 
turn off the display. 
 
 
 
 
 
 
 
 
 
 
       Screw                     
               Main switch cover 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
						

							                                         User Manual BDL4631V/00 
 
 17 
 
Install the LCD Monitor in Portrait Mode 
BDL4631V can be installed in portrait position, under the following conditions:  Caution: 
Portrait mode is effective only when wall-mounted or ceiling-mounted. The feet can not be used for the monitor in portrait position. 
Placing the monitor in portrait position, will shorten the average life of the LC D backlight.  
Operational Environment (Temperature) shall be limited, as shown below: 
 
Operational 
Environment 
Temperature 5 - 35 °C / 41 - 95 °F 
Humidity 20 - 80 % (without condensation) 
 
 Please orientate the monitor in the direction shown as the right figure: 
Do not place monitor in landscape in any other ma nn er.   How to set-up  
1. Rem ov e the feet if they are attached. 
2. The “” logo should be on the RIGHT side when facing the monitor.                 
 
  
 
How to Remove the Logo for landscape mode?  1. Prepare a piece of paper with a cutting area of logo as a protector to  prevent the front bezel from scratching. 2. Using an knife, carefully remove the logo sticker with the paper placing beneath. 
3. Tear off the logo sticker. 
 
  
 
  
 
  
How to Use the Logo Guider for Portrait Mode? 
 1. Before applying, make sure the guider is well shaped.  The PHILIPS                                   sticker attached on the end of it could be folded back as figure a.  
2. Turn  back  the logo  end  of  the  guider  and  remove  the  sticky  tape  of  the logo. 3. Slide  the  logo  guider  along  the  short  side  of  the  front  bezel  as figure c & then re-turn the logo end of the guider back to the right side. 4. With your left hand fixing the guider, scrunch the logo by your right hand to make it stuck firmly on the front bezel. 
5. Remove the guider and leave the logo over the front bezel. 
 
 
 
 
         Counterclockwise                  Clockwise