Philips 52pfl8605k User Manual

							Then  use an  HDMI  cable  to  connect the  digital receiver to  the  TV.
Finally,  use an  HDMI  cable  to  connect the  Disc  Recorder to  the  TV.
Dig. receiver + Disc-R + Home  Theatre
First, use 3 antenna  cables to  connect the  devices  to  the  TV.
Connections /  Connect devices61
 
						

							Then  use an  HDMI  cable  to  connect the  digital receiver to  the  TV.
Then  use an  HDMI  cable  to  connect the  Disc  Recorder to  the  TV.
Then  use an  HDMI  cable  to  connect the  Home  Theatre System to
the  TV.
62Connections /  Connect devices
 
						

							If  you  do not  use the  HDMI -ARC  connection  on  the  TV  and  the
device,  add  a  digital audio cable  (cinch  coaxial).
Digital  HD receiver
First, use 2 antenna  cables to  connect the  device to  the  TV.
Use  an  HDMI  cable  to  connect the  device to  the  TV.
Connections /  Connect devices63
 
						

							64Connections /  Connect devices
 
						

							5.4Connect more devices
Game
Connect a  game  console  to  the  side  or back  of  the  TV.  You  can  use
an  HDMI, YPbPr  or Scart  connection. If  your  game  console  only has
Video (CVBS)  and  Audio L/R output, use a   Video  Audio  L/R to
Scart  adapter to  connect to  the  Scart  connection.
Picture delay
To  prevent   picture delay  while gaming, close Help and  press   s
(Adjust)  and  select  Smart picture > Game and  press   OK.  After
gaming, do not  forget to  select the  Smart picture you  normally  use
for  watching  TV.
Use  an  HDMI  cable  to  connect the  device to  the  side  of  the  TV.
Or use a  Scart  adapter to  connect the  device to  the  TV.
HD Game
Use  an  HDMI  cable  or YPbPr  and  Audio L/R cables to  connect a
High Definition  game  console  to  the  TV.
To  connect a  HD Game console,  read  Help > Connections  >
Connect  more  devices  > Game.
Photo camera
Connections /  Connect more devices 65
 
						

							To  view pictures stored  on  your  digital photo camera,  you  can
connect the  camera  directly  to  the  TV.  Use  the  USB  connection  on
the  side  of  the  TV  to  connect. Switch on  the  camera  after  you  made
the  connection.
If  the  list  with  the  content  of  the  camera  does not  appear
automatically,  your  camera  might  need to  be set to  transfer its
content  with  PTP  (Picture Transfer Protocol). Read the  user manual
of  the  digital photo camera.
Camcorder
Connect a  camcorder to  the  side  or back  of  the  TV.  You  can  use an
HDMI, YPbPr  or Scart  connection. If  your  camcorder only has  Video
(CVBS)  and  Audio L/R output, use a  Video  Audio  L/R to Scart
adapter to  connect to  the  Scart  connection.
See  the  following  pages  to  connect your  camcorder.
Use  an  HDMI  cable  to  connect the  camcorder to  the  side  of  the
TV.
Or use a  Scart  adapter to  connect the  device to  the  TV.
66 Connections /  Connect more devices
 
						

							TV as PC monitor
You  can  connect the  TV  to  your  computer  as  a  PC  monitor.  Before
connecting the  PC,  set the  PC  monitor  refresh rate to  60 Hz.
See  the  following  pages  for  how to  connect your  computer.
Use  a  VGA cable  to  connect the  PC  to  the  VGA connector  and  an
audio L/R cable  to  connect the  VGA Audio L/R to  the  back  of  the
TV.
Use  a  DVI to  HDMI  adapter to  connect the  PC  to  HDMI  and  an
audio L/R cable  to  connect the  Audio L/R to  the  back  of  the  TV.
Connections /  Connect more devices67
 
						

							Ideal TV setting
Set the  TV  Picture format  to  Unscaled for  the  sharpest picture
quality.  While watching  TV,  press  o,  select  Picture format  and
select  Unscaled .
For a  list  of  supported  resolutions  see  Help > Specifications  >
Display  resolutions .
Decoder
Use  a  scart cable  to  connect a  decoder  that  decodes analogue
antenna  channels.  Use  the   EXT1 or EXT2  connectors on  the  back
of  the  TV.
You  have to  assign the  TV  channel as  a  channel to  be decoded.
Then  assign the  connection  where the  decoder  is connected.
To  assign this  TV  channel, press   h > Setup  > Channel settings  >
Decoder .  Select  Channel to  set up the  channel that  you  want  to
decode.  Select   Status to  set the  connection  you  use for  the
decoder.
68 Connections /  Connect more devices
 
						

							5.5Network
Wired
To  set up the   wired network  connection ,  read Help > Setup  >
Network
Connect the  router to  the  TV  with  a  network  cable.  To  fullfill EMC
regulations, use a  shielded  FTP  Cat. 5E ethernet  cable.
Wi-Fi Ready
This  TV  is Wi-Fi Ready. With  the  Wireless USB  adapter PTA01
accessory (sold  separately) you  can  connect the  TV  to  your  network
wirelessly.  You  can  connect to  Net TV  - the  best of  the  web  on
your  TV  - wireless and  hassle free.
Make your TV wireless
1  Switch on  your  wireless network  router.
2  Insert the  USB  adapter PTA01 in  the  USB  connection  at the  side
of  the  TV.  The wireless installation  starts automatically.
3  Follow  the  instructions on  screen.
WPS  - Wi -Fi  Protected  Setup
If  your  router has   WPS  (Wi-Fi Protected Setup),  go to  the  router
and  press  the  WPS  button. Return  to  the  TV  within  2 minutes,
select  Easy connect  and  press  OK.  The TV  connects to  your
network. This  takes about  2 minutes.  The finish the  installation.
Most new  wireless routers have the  WPS  system  and  carry  the  WPS
logo. The WPS  system  uses   WPA security encryption and  cannot  be
combined with  devices  on  your  network  that  use the  WEP  security
encryption.  If  you  still need this  WEP  device in  your  network, install
with   Scan > Custom .
Scan for  routers
If  you  have several  routers in  your  network, you  can  select the
network  you  need. To  select a  specific network  router, press   Scan
on  the  first  page  of  the  installation.  The routers with  WPS  and  with
the  strongest signal are shown  first  in  the  list.
Select  the  router you  need and  press   Easy connect if  the  router has
WPS.  Or press   Pin code if  you  can  enter the  PIN code  in  your
router software to  connect. Or press   Custom to  enter the
encryption  key manually.
PIN code
To  make  the  secured connection  with  a  PIN code, select  PIN code
and  press   OK.  Write down the  8 digit  PIN code  shown  and  enter it
in  the  router software on  your  PC.  See  the  router manual where to
enter the  PIN code.
Custom
To  enter the   encryption key (the  security key) manually, select
Custom  and  press   OK.  If  you  have WPA security on  your  router,
enter the  passphrase with  the  remote control. To  open  the  on -
screen keyboard, select the  text entry  field  and  press   OK.
If  you  have  WEP  security encryption ,  the  TV  asks for  the  WEP
encryption  key in  hexadecimal  numbers.  Find this  hexadecimal  key in
the  router software on  your  PC.  Write down the  first  key of  the
WEP  keys  list  and  enter it on  TV  with  the  remote control. If  the
security key is accepted, the  TV  is connected with  the  wireless
router.
If  asked, agree to  the  End User  licence Agreement.
Attention
Leave  the  Wireless USB  adapter permanently in  the  USB  connection.
With  the  TV  connected to  your  wireless network, the  free  Wi-Fi
MediaConnect  software can  bring  up -project - your  PC  screen on
the  TV.  You  can  project  video, music, presentations,  etc. playing on
your  laptop or desktop PC.
The playback of  video can  be affected  by  your  PC  performance  and
your  wireless network  bandwidth.
What you need
To  enjoy Wi-Fi MediaConnect, you  need to  install the  free  software
on  your  PC.
Install Wi -Fi  MediaConnect
1  Insert the  Wi-Fi MediaConnect  CD -ROM  in  your  PC.  The CD -
ROM  disc that  came  with  the  PTA01.
2  Your  PC  starts your  Internet browser  and  opens the  Wi-Fi
MediaConnect  download page  - www.philips.com/wifimediaconnect.
On the  website,  you  can  check the  necessary PC  system
requirements.
3  Enter  the  code  printed on  the  CD -ROM  envelope.
4  Click the  Download now button to  download the  free  Wi-Fi
MediaConnect  software.
5  Once downloaded, start the  file  Wi -Fi MediaConnect_setup.exe.
Follow  the  instructions on  screen.
TV network name
If  you  have more then  one  TV  in  your  home  network, you  can
rename this  TV.  To  rename this  TV  in  the  network, press   h >
Setup  > Network settings  and  select TV network name .
To  enter the  name,  press   OK to  open  the  on -screen keyboard or
use the  remote control keypad.
Connections /  Network 69
 
						

							Start  projecting
To  start projecting the  PC  screen on  TV,  click on  the  small  TV  like
icon in  the  taskbar  at the  bottom right of  the  PC  screen. Your  PC
screen appears on  your  TV  screen.
Stop  projecting
To  stop projecting, click on  the  TV  icon again.
Wi -Fi  MediaConnect  Help
To  read the  Wi-Fi MediaConnect  Help, right click the  program  icon
in  the  notification tray of  the  PC  and  select Help.
Specifics
You  can  project  high  definition (HD) or standard  definition (SD)
video, depending on  the  processing  power of  your  PC.
The content  protection  on  most DVD or Blu-ray  Disc  movies  might
restrict watching  the  movie on  TV  when  the  disc is playing on  a  PC.
The TV  shows  PC  media files  with  a  small  delay.
Wi-Fi MediaConnect  is only available  for  PC.
PC requirements
Windows XP, Vista, Windows 7 (PC  only)
Minimum  PC  requirements
• Intel® Pentium Core™ 2 Duo  1.8GHz
• 512MB RAM
• 200MB free  hard  disk space
• Wi-Fi 802.11g
• Broadband  Internet connection
Recommended  PC  requirements
• Intel® Pentium Core™ 2 Duo  2.1GHz
• 1GB RAM
• 200MB free  hard  disk space
• Wi-Fi 802.11n  for  router and  PC
• Broadband  Internet connection
70 Connections /  Network