Philips 46pfl8505k User Manual

5.7Common Interface CAM
CAM
Scrambled  digital  TV   channels  can  be   decoded   with  a   ConditionalAccess   Module   (CAM).   Digital   TV   service   operators   provide   the  CAMwhen  you   subscribe   to  their  services.  Contact  a   digital  TV   serviceoperator   for  more   information  and  to  see   terms  &  conditions.
Insert   a  CAMSwitch   off   the   TV   before   inserting   a  CAM.Look  on   the   CAM   for   the   correct   method  of   insertion.  Incorrectinsertion   can...

5.83D
3D
This   TV   is  prepared   for   the   3D   Full  HD   accessory  PTA02  (soldseparately   - only  for   40-46PFL8505/8605   and  52PFL8605).
PTA02   Installation1 Switch   off   the   TV.2 Connect  the   3D   transmitter   to  the   3D   connection  3D   Out  onthe   back   of   the   TV.
3 Install   the   3D   transmitter   on   the   top   or  at  the   bottom  of   theTV.   Make   sure  to  point   the   transmitter   directly   to  where   you   sitto  watch   TV.
The  small   window   in...

6
6.1
Troubleshooting
Contact information
If   the   advice   and  suggestions  in   Troubleshooting   do   not   helpresolve   the   problem,  try   switching   the   TV   off   and  back   on   again.
WarningIf   your   TV   breaks  down, NEVER  try   to  repair   the   TV   yourself.
Consumer  CareIf   the   TV   problem  is  not   solved   you   can   call  the   PhilipsConsumer   Care  hotline   in   your   country.   Look  up  the   TV   modeland  serial  number  before   you   call.  Find  the...

6.2TV and remote control
The   TV  does   not   switch   on•   Switch   the   TV   off   and  on   again  with   the   switch   on   the   bottomof   the   TV.•   Check   the   power   cable   connection.•   Try  using   the   keys   on   the   TV   to  switch   on.
The   TV  does   not   switch   on   from  standby•   Check   that  the   batteries   of   the   remote   control   are   not   emptyor  weak.  Check   their   +  /   -  orientation.•   Try  using   the   keys   on   the   TV   to  switch...

6.3TV channels
Some   TV  channels   are  gone•   Check   if  the   correct   list   is  selected  in   the   Channel   list.  With
the   Channel   list   on   screen,  press  o  (Options)  and  select  the   listyou   need  with  Select  list.
•   A   channel  could   be  hidden   in   the   Channel   list.  Read  moreabout   Channel   list   in  Help > Use   your  TV > Menus > Browse.
No  digital   channel  found  during  installation•   Check   if  the   TV   supports  DVB-T   or  DVB-C   in   your...

6.4Picture and sound
No  picture•   Check   if  the   antenna  is  connected   properly.•   Check   if  the   correct   device   is  selected  and  connected   properly.
•   Check   the   contrast   or  brightness   setting  in  h > Setup > TVsettings > Contrast  or Brightness.
The   picture  is   poor•   Bad   weather  can   influence   the   picture   quality.•   Check   if  the   antenna  is  connected   properly.•   Non -earthed   audio   devices,   neon   lights,   high   buildings   ormountains...

6.5Devices
HDMI  connections•   The  HDMI -HDCP  procedure  might  take  a  few  seconds   beforethe   picture   from  a  device   appears.•   If   the   TV   does  not   recognise   the   device   and  there  is  nopicture,   try   switching   from  one  device   to  another  and  back   againto  restart  the   HDCP  procedure.
•   If   sound   interruptions   occur  persistently,   see  the   user  manual   ofthe   device   to  check   the   output  settings.  If   that  does  not   help,connect   an...

6.6Multimedia
The   files  on   my  USB  device   are  not   shown•   Set   your   device   (camera)  to  ‘Mass  Storage  Class’  compliant.•   The  USB   device   may   need  specific   driver   software.Unfortunately,   this   software   cannot   be  downloaded   to  your   TV.
•   Not   all   audio   and  picture   files   are   supported.  See  the   list   inHelp > Specifications > Multimedia.
Files  from  a  USB  device   do  not   play   back  smoothly•   The  transfer  performance   of   the...

6.7Network
Net   TV  does   not   work•   If   the   connection   to  the   router   is  OK,  check   the   routerconnection   to  the   Internet.•   You   need  a  high -speed  Internet  connection   for   your   router.
Troubleshooting   /   Network79
 

7
7.1
Specifications
Software
Software version
To   view   the   current  TV   software   version,  press  h > Setup >Software   settings  and  press  OK.  Select  Current  software  infoand  read Version:.
Open source software
This   television  contains open   source   software.  Philips  herebyoffers  to  deliver   or  make  available,  upon   request,   for   a  charge   nomore   than   the   cost   of   physically   performing  source   distribution,   acomplete   machine   readable   copy  of   the...