Philips 40PFS5501 Manual

							22
Wireless and
Networks
22.1
Network
For more information, in  Help , press the colour
key 
  Keywords  and look up  Network , for more
information on connecting the TV to a network.
22.2
Bluetooth
What You Need
You can connect a wireless device with Bluetooth® to
this TV – a wireless speaker, a subwoofer, a sound
bar or headphones. You can also connect a wireless
gamepad with Bluetooth LE.
To play the TV sound on a wireless speaker, you must
pair the wireless speaker with the TV. You can pair
some wireless speakers and a maximum of 4
Bluetooth LE (low energy) devices. The TV can only
play the sound on one speaker at a time. If you
connect a subwoofer, the sound is played on the TV
and the subwoofer. If you connect a sound bar the
sound is played on the sound bar only.
Attention - Audio to Video syncronisation    
Many Bluetooth speaker systems have a high, so
called, 'latency'. High latency means that the audio
lags behind the video, causing unsynchronised 'lip
sync'. Before you purchase a wireless Bluetooth
speaker system, inform yourself about the newest
models and look for a device with a low latency
rating. Ask your dealer for advice.
For more information on how to pair a wireless
speaker, in  Help , press the colour
key 
  Keywords  and look up  Bluetooth, Pairing .
Pairing a Device
For more information, in  Help , press the colour
key 
  Keywords  and look up  Bluetooth,
Pairing  for more information on pairing wireless
devices. Select a Device
For more information, in  Help , press the colour
key 
  Keywords  and look up  Bluetooth, Select
device  for more information on how to select a
wireless speaker.
Remove a Device
For more information, in  Help , press the colour
key 
  Keywords  and look up  Bluetooth, Remove
device  for more information on how to unpair
(remove) a wireless Bluetooth device.
Bluetooth On or Off
To connect wireless Bluetooth devices, make sure
Bluetooth is switched on.
To switch Bluetooth on…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Wireless and Networks  and press  OK .
3 -  Select  Bluetooth  >  Bluetooth On/Off  and
press  OK .
4 -  Select  On  or  Off  and press  OK .
5 -  Press 
  (left) repeatedly if necessary, to close
the menu.
71 
						

							23
Android Settings
You can set or view several Android specific settings
or information. You can find the list of apps installed
on your TV and the storage space they need. You can
set the language you like to use with Voice
Search. You can configure the onscreen keyboard or
allow apps to use your location. Explore the different
Android settings. You can go
to  www.support.google.com/androidtv  for more
information on these settings.
To open these settings…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Android Settings , and press  OK .
3 -  Explore the different Android settings.
4 -  Press 
   BACK  if necessary, to close the menu.
72 
						

							24
Channel Installation
24.1
Antenna/Cable Installation
Update Channels
Automatic Channel Update
If you receive digital channels, you can set the TV to
automatically update these channels.
Once a day, at 6 AM, the TV updates the channels
and stores new channels. New channels are stored in
the Channels List and are marked with a 
  .
Channels without a signal are removed. The TV must
be in standby to automatically update channels. You
can switch off Auromatic Channel Update.
To switch off the automatic update…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Antenna/Cable
Installation  and press  OK .
3 -  Enter your PIN code if necessary.
4 -  Select  Automatic Channel Update  and
press  OK .
5 -  Select  Off  and press  OK .
6 -  Press 
   BACK  to close the menu. 
When new channels are found or if channels are
updated or removed, a message is shown at TV start
up. To avoid this message to appear after every
channel update, you can switch it off.
To switch off the message…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Antenna/Cable
Installation  and press  OK .
3 -  Enter your PIN code if necessary.
4 -  Select  Channel Update Message  and press  OK .
5 -  Select  Off  and press  OK .
6 -  Press 
   BACK  to close the menu. 
In certain countries, the Automatic channel update is
done while watching TV or on any moment when the
TV is in standby. 
Manual Channel Update
You can always start an channel update yourself.
To start a channel update manually…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Antenna/Cable
Installation  and press  OK .
3 -  Enter your PIN code if necessary.
4 -  Select  Search for Channels  and press  OK .
5 -  Select  Start  and press  OK . 6 -  Select  Update Digital Channels ,
select  Next  and press  OK .
7 -  Select  Start  and press  OK  to update the digital
channels. This can take a few minutes.
8 -  Press 
   BACK  to close the menu.
Reinstall Channels
Reinstall All Channels
You can reinstall all channels and leave all other TV
settings untouched. 
If a PIN code is set, you will need to enter this code
before you can reinstall channels.
To reinstall channels…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Antenna/Cable
Installation  and press  OK .
3 -  Enter your PIN code if necessary.
4 -  Select  Search for Channels  and press  OK .
5 -  Select  Start  and press  OK.
6 -  Select  Reinstall Channels , select  Next  and
press  OK .
7 -  Select the country where you are now and
press  OK .
8 -  Select  Next  and press  OK .
9 -  Select the type of installation you want,  Antenna
(DVB-T)  or  Cable (DVB-C)  and press  OK .
8 -  Select  Next  and press  OK .
11 -  Select the type of channels you want,  Digital
and Analogue Channels  or  Only Digital
Channels  and press  OK .
8 -  Select  Next  and press  OK .
13 -  Select  Start  and press  OK  to update the
digital channels. This can take a few minutes.
14 -  Press 
   BACK  to close the menu.
Reinstall TV
You can redo a full TV installation. The TV is
completely reinstalled.
To redo a full TV installation…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  General Settings  >  Reinstall TV  and
press  OK .
3 -  Enter your PIN code if necessary.
4 -  Select  Yes  and press  OK  to confirm.
5 -  The TV will reinstall completely. All settings will
be reset and installed channels will be replaced. The
installation can take a few minutes.
6 -  Press 
   BACK  to close the menu.
73 
						

							DVB-T or DVB-C
DVB Settings
Network Frequency Mode
If you intend to use the fast  Quick Scan  method
in  Frequency Scan  to search for channels,
select  Automatic . The TV will use 1 of the predefined
network frequencies (or HC - homing channel) as
used by most cable operator in your country.
If you received a specific network frequency value to
search for channels, select  Manual .
Network Frequency
With the  Network Frequency Mode  set to  Manual ,
you can enter the network frequency value received
from your cable operator here. To enter the value, use
the number keys.
Frequency Scan
Select the method of searching for channels. You can
select the faster  Quick Scan  method and use the
predefined settings used by most cable operator in
your country.
If this results in having no channels installed or if
some channels are missing, you can select the
extended  Full Scan  method. This method will take
more time to search for and install channels.
Frequency Step Size
The TV searches for channels in steps of  8MHz .
If this results in having no channels installed or if
some channels are missing, you can search in smaller
steps of  1MHz . Using the 1MHz steps will take more
time to search for and install channels.
Digital Channels
If you know your cable operator is not offering digital
channels, you can skip searching for digital channels.
Analogue Channels
If you know your cable operator is not offering
analogue channels, you can skip searching for
analogue channels. Free / Scrambled
If you have a subscription and a CAM - Conditional
Access Module for pay TV services, select  Free +
Scrambled . If you did not subscribe to pay TV
channels or services, you can select  Free
Channels Only .
For more information, in  Help , press the colour
key 
  Keywords  and look up  CAM, Conditional
Access Module .
Reception Quality
You can check the quality and signal strength of a
digital channel. If you have your own antenna, you
can reposition the antenna to try and improve the
reception.
To check the reception quality of a digital channel…
1 -  Tune to the channel.
2 -  Press 
 , select  All Settings  and press  OK .
3 -  Select  Channels  >  Antenna/Cable
Installation  and press  OK . Enter your PIN code if
necessary.
4 -  Select  Digital: Reception Test  and press  OK .
5 -  Select  Search  and press  OK . The digital
frequency is shown for this channel.
6 -  Select  Search  again and press  OK  to check the
signal quality of this frequency. The test result is
shown on screen. You can reposition the antenna or
check the connections to possibly improve the
reception.
7 -  You can also change the frequency
yourself. Select the frequency number one by one
and use the 
  (up) or 
  (down) keys to change
the value. Select  Search  and press  OK  to test the
reception again.
8 -  Press 
  (left) repeatedly if necessary, to close
the menu.
Manual Installation
Analogue TV channels can be manually installed,
channel by channel.
To install analogue channels manually…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Antenna/Cable
Installation  and press  OK . Enter your PIN code if
necessary.
3 -  Select  Analogue: Manual Installation  and
press  OK . 
•  System
To set up the TV system, select  System .
Select your country or the part of the world where
you are now and press  OK .
74 
						

							•  Search Channel
To find a channel, select  Search Channel  and
press  OK . You can enter a frequency yourself to find
a channel or let the TV search for a channel.
Press 
  (right) to select  Search  and press  OK  to
search for a channel automatically. The found
channel is shown on screen and if the reception is
poor, press  Search  again. If you want to store the
channel, select  Done  and press  OK .
•  Store
You can store the channel on the current channel
number or as a new channel number.
Select  Store Current Channel  or  Store as New
Channel  and press  OK . The new channel number is
shown briefly. 
You can redo these steps until you have found all
available analogue TV channels.
24.2
Satellite Installation
About Installing Satellites
This TV has two built-in satellite DVB-S/DVB-S2
tuners.
Up to 4 Satellites    
You can install up to 4 satellites (4 LNBs) on this TV.
Select the exact number of satellites you wish to
install at the start of the installation. This will speed up
the installation.
Unicable    
You can use a Unicable system to connect the
antenna dish to the TV. You can select Unicable for 1
or for 2 satellites at the start of the installation.
MDU - Multi-Dwelling-Unit    
The built-in satellite tuners support MDU on the Astra
satellites and for Digiturk on the Eutelsat satellite.
MDU on Türksat is not supported.
Start the Installation
Make sure your satellite dish is connected correctly
and is perfectly aligned before you start the
installation.
To start the satellite installation…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Satellite Installation  and
press  OK . Enter your PIN code if necessary.
3 -  Select  Search for Satellite  and press  OK .
4 -  Select  Search  and press  OK . TV will search for
satellites. 5 -  Select  Install  and press  OK . The TV shows the
current satellite installation setup.
If you want to change this setup, select  Settings .
If you don't want to change the setup, select  Search .
Go to step  5 .
6 -  In  Installation System , select the number of
satellites you want to install or select one of the
Unicable systems. When you select Unicable, you
can choose the User Band Numbers and enter the
User Band Frequencies for each tuner. In some
countries, you can adjust some expert settings for
each LNB in  More Settings .
7 -  The TV will search for the satellites available on
the alignment of your antenna dish. This may take a
few minutes. If a satellite is found, its name and
reception strength are shown on screen.
8 -  When the TV found the satellites you need,
select  Install .
9 -  If a satellite offers  Channel Packages , the TV will
show the available packages for that satellite. Select
the package you need. Some packages offer
a  Quick  or  Full  install for their available channels,
select one or the other. The TV will install the satellite
channels and radio stations.
10 -  To store the satellite setup and installed
channels and radio stations, select  Finish .
Satellite Installation Settings
The satellite installation settings are preset according
your country. These settings determine how the TV
searches and installs satellites and its channels. You
can always change these settings.
To change the satellite installation settings…
1 -  Start the satellite installation.
2 -  On the screen where you can start searching for
satellites, select  Settings  and press  OK .
3 -  Select the number of satellites you want to install
or select one of the Unicable systems. When you
select Unicable, you can choose the User Band
Numbers and enter the User Band Frequencies for
each tuner.
4 -  When you're done, select  Next  and press  OK .
5 -  On the Settings menu, press the colour
key 
  Done  to return to the screen to start
searching for satellites.
Homing Transponder and LNB    
In some countries, you can adjust the expert settings
for homing transponder and each LNB. Only use or
change these settings when a normal installation fails.
If you have non-standard satellite equipment, you
can use these settings to overrule the standard
settings. Some providers might give you some
transponder or LNB valeus which you can enter here.
75 
						

							Satellite CAMs
If you use a CAM – a Conditional Access Module with
a smart card – to watch satellite channels, we
recommend to do the satellite installation with the
CAM inserted in the TV. 
Most CAMs are used to descramble channels.
Newest generation CAMs (CI+ 1.3 with Operator
Profile), can install all the satellite channels by
themselves on your TV. The CAM will invite you to
install its satellite(s) and channels. These CAMs not
only install and descramble the channels but also
handle regular channel updates. 
Channel Packages
Satellite operators can offer channel packages that
bundle free channels (free-to-air) and offer a sorting
that suits a country. Some satellites offer subscription
packages - a collection of channels you pay for.
If you choose a subscription package, the TV might
ask you to select a Quick or Full installation.
Select  Quick  to install the channels of the package
only or select  Full  to install the package and all
other available channels too. We recommend a Quick
installation for subscription packages. If you have
additional satellites that are not part of your
subscription package, we recommend a Full
installation. All installed channels are put in the
channels list All.
Unicable Setup
The Unicable System
You can use a Single Cable system, MDU or Unicable
system to connect the antenna dish to the TV. A
Single Cable system uses one cable to connect the
satellite dish to all satellite tuners in its system. A
Single Cable system is typically used in apartment
buildings. If you use a Unicable system, the TV will ask
you to assign a user band number and corresponding
frequency during the installation. You can install 1 or 2
satellites with Unicable on this TV.
If you notice some missing channels after a Unicable
installation, another installation might have been
done at the same moment on the Unicable system.
Do the installation again to install the missing
channels. User Band Number
In a Unicable system, each connected satellite tuner
must be numbered (e.g. 0, 1, 2 or 3 etc.).
You can find the available user bands and their
number on the Unicable switchbox. User band is
sometimes shortened as UB. There are Unicable
switchboxes that offer 4 or 8 user bands. If you select
Unicable in the settings, the TV will ask you to assign
the unique user band number for each built-in
satellite tuners. A satellite tuner cannot have the same
user band number as another satellite tuner in the
Unicable system.
User Band Frequency
Next to the unique user band number, the built-in
satellite receiver needs the frequency of the selected
user band number. These frequencies are mostly
shown next to the user band number on a Unicable
switchbox.
Add a Satellite
You can add an additional satellite to your current
satellite installation. The installed satellites and their
channels remain untouched. Some satellite operators
do not allow adding a satellite.
The additional satellite should be seen as an extra, it
is not your main satellite subscription or not the main
satellite of which you use its channel package.
Typically, you would add a 4th satellite when you
have 3 satellites already installed. If you have 4
satellites installed, you might consider removing one
first to be able to add a new satellite.
Setup    
If you currently have only 1 or 2 satellites installed, the
current installation settings might not allow adding an
extra satellite. If you need to change the installation
settings, you must redo the complete satellite
installation. You cannot use  Add satellite  if a change
of settings is needed.
To add a satellite…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Satellite Installation  and
press  OK .
3 -  Select  Search for satellite  and press  OK .
4 -  Select  Add Satellite  and press  OK . The current
satellites are shown.
5 -  Select  Search  and press  OK . The TV will
search for new satellites.
6 -  If the TV has found one or more satellites,
select  Install  and press  OK . The TV installs the
channels of the found satellites.
76 
						

							7 -  Select  Finish  and press  OK  to store the
channels and radio stations.
Remove a Satellite
You can remove one or more satellites from your
current satellite installation. You remove the satellite
and its channels. Some satellite operators do not
allow removing a satellite.
To remove satellites…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Satellite Installation  and
press  OK .
3 -  Select  Search for satellite  and press  OK .
4 -  Select  Remove Satellite  and press  OK . The
current satellites are shown.
5 -  Select a satellite and press  OK  to mark or
unmark them to remove.
6 -  Press 
  (left) repeatedly if necessary, to close
the menu.
Manual Installation
Manual Installation is intended for expert users.
You can use Manual Installation to quickly add new
channels from a satellite transponder. You need to
know the frequency and polarization of the
transponder. The TV will install all channels of that
transponder. If the transponder was installed before,
all its channels - the former and the new ones - are
moved to the end of the channel list All.
You cannot use Manual installation if you need to
change the number of satellites. If this is needed, you
have to do a complete installation with Install
Satellites.
To install a transponder…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  >  Satellite Installation  and
press  OK .
3 -  Select  Manual Installation  and press 
  (right)
to enter the menu.
4 -  If you have more than 1 satellite installed, select 
LNB  for which you want to add channels.
5 -  Set the  Polarisation  you need. If you set
the  Symbol Rate Mode  to  Manual , you can enter
the symbol rate in  Symbol Rate  manually.
6 -  Press the arrows 
  (up) or 
  (down) to adjust
the frequency, and select  Done .
7 -  Select  Search  and press  OK . The signal
strenght is shown on screen.
8 -  If you want to store the channels of a new
transponder, select  Store  and press  OK .
9 -  Press 
  (left) repeatedly if necessary, to close
the menu.  Homing Transponder and LNB
In some countries, you can adjust the expert settings
for homing transponder and each LNB. Only use or
change these settings when a normal installation fails.
If you have non-standard satellite equipment, you
can use these settings to overrule the standard
settings. Some providers might give you some
transponder or LNB valeus which you can enter here.
LNB Power    
By default, LNB Power is set to On.
22 kHz Tone    
By default, the Tone is set to Auto.
Low LO Frequency / High LO Frequency    
The local oscillator frequencies are set to standard
values. Adjust the values only in case of exceptional
equipment that needs different values.
Problems
The TV cannot find the satellites I want or the TV
installs the same satellite twice    
• Make sure that the correct number of satellites is set
in Settings at the start of the installation. You can set
the TV to search for One, Two or 3/4 satellites.
A dual head LNB cannot find a second satellite    
• If the TV finds one satellite but cannot find a second
one, turn the dish a few degrees. Align the dish to get
the strongest signal on the first satellite. Check the
signal strength indicator of the first satellite on screen.
With the first satellite set at the strongest signal, select
Search again to find the second satellite.
• Make sure the settings are set to Two Satellites.
Changing the installation settings did not solve my
problem    
• All settings, satellites and channels are only stored
at the end of the installation when you finish.
All satellite channels are gone    
• If you use a Unicable system, make sure you
assigned two unique user band numbers for both
built-in tuners  in the Unicable settings. It might be
that another satellite receiver in your Unicable system
is using the same user band number.
Some satellite channels seem to have disappeared
from the channel list    
• If some channels seem to be gone or displaced, the
broadcaster might have changed the transponder
location of these channels. To restore the channel
positions in the channel list, you can try an update of
77 
						

							the channel package.
I cannot remove a satellite    
• Subscription packages do not allow removing a
satellite. To remove the satellite, you have to do a
complete installation again and select another
package.
Sometimes the reception is poor    
• Check if the satellite dish is solidly mounted. Strong
winds can move the dish.
• Snow and rain can degrade the reception.
24.3
Channel List Copy
Introduction
Channel List Copy is intended for dealers and expert
users. In some countries, Channel List Copy is only
available for copying satellite channels.
With Channel List Copy, you can copy the channels
installed on one TV onto another Philips TV of the
same range. With Channel List Copy, you avoid the
time-consuming channel search by uploading a
predefined channel list on a TV. Use a USB flash drive
of minimum 1 GB.
Conditions  
• Both TVs are from the same year range.
• Both TVs have the same hardware type. Check the
hardware type on the TV type plate on the back of
the TV. Typically noted as Q . . . LA
• Both TVs have compatible software versions.
Current software version    
To check the cuurent version of the TV software…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Update Software  and press 
  (right) to
enter the menu.
3 -  Select  Current Software Info  and press  OK .
4 -  The version, release notes and creation date are
shown. Also, the Netflix ESN Number is shown if
available.
5 -  Press 
  (left) repeatedly if necessary, to close
the menu.
Copy a Channel List
To copy a channel list…
1 -  Switch on the TV. This TV should have channels
installed.
2 -  Plug in a USB flash drive.
3 -  Press 
 , select  All Settings  and press  OK .
4 -  Select  Channels  >  Channel List Copy  and
press  OK . 5 -  Select  Copy to USB  and press  OK . You might
be asked to enter the Child Lock PIN code to copy the
channel list.
6 -  When copying is done, unplug the USB flash
drive.
7 -  Press 
  (left) repeatedly if necessary, to close
the menu. 
Now you can upload the copied channel list onto
another Philips TV.
Channel list version
Check the current version of the channel list...
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Channels  and press 
  (right) to enter
the menu.
3 -  Select  Channel List Copy  and select  Current
Version , then press  OK .
4 -  Press 
  (left) repeatedly if necessary, to close
the menu. 
Upload a Channel List
To not Installed TVs
Depending on whether your TV is already installed or
not, you must use a different method to upload a
channel list.
To a TV that is not yet installed  
1 -  Plug in the power plug to start the installation and
select language and country. You can skip the
channel search. Finish the installation.
2 -  Plug in the USB flash drive that holds the channel
list of the other TV.
3 -  To start the channel list upload, press 
 ,
select  All Settings  and press  OK .
4 -  Select  Channels  >  Channel List Copy  >  Copy
to TV  and press  OK . Enter your PIN code if
necessary.
5 -  The TV notifies you if the channel list is copied to
the TV successfully. Unplug the USB flash drive.
To Installed TVs
Depending on whether your TV is already installed or
not, you must use a different method to upload a
channel list.
To an already installed TV  
1 -  Verify the country setting of the TV. (To verify this
setting, see chapter Reinstall All Channels. Start this
procedure until you reach the country setting.
Press 
   BACK  to cancel the installation.)
If the country is correct continue with step 2.
If the country is not correct, you need to start a
78 
						

							reinstallation. See chapter Reinstall All Channels and
start the installation. Select the correct country and
skip the channels search. Finish the installation. When
done, continue with step 2.
2 -  Plug in the USB flash drive that holds the channel
list of the other TV.
3 -  To start the channel list upload, press 
 ,
select  All Settings  and press  OK .
4 -  Select  Channels  >  Channel List Copy  >  Copy
to TV  and press  OK . Enter your PIN code if
necessary.
5 -  The TV notifies you if the channel list is copied to
the TV successfully. Unplug the USB flash drive.
79 
						

							25
Software
25.1
Update Software
Update from Internet
If the TV is connected to the Internet, you may receive
a message to update the TV software. You need a
high-speed (broadband) Internet connection. If you
receive this message, we recommend you to carry out
the update.
With the message on screen, select  Update  and
follow the instructions on screen.
You can also ook for a software update yourself.
During the software update, there is no picture and
the TV will switch off and on again. This might happen
several times. The update can take a few minutes.
Wait until the TV picture comes back up. Do not press
the power switch 
  on the TV or on the remote
control during the software update.
To look for a software update yourself…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Update Software  >  Search for
Updates  and press  OK .
3 -  Select  Internet  and press  OK .
4 -  The TV will look for an update on the Internet.
5 -  If an update is available, you can update the
software right away.
6 -  A software update can take several minutes. Do
not press the 
  key on the TV or remote control.
7 -  When the update is done, the TV will return to the
channel you were watching.
Update from USB
It might be necessary to update the TV software. You
need a computer with an high-speed Internet
connection and a USB flash drive to upload the
software on the TV. Use a USB flash drive with at least
500MB free space. Make sure that write protection is
switched off.
To update the TV software…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Update Software  >  Search for
Updates  and press  OK .
3 -  Select  USB  and press  OK .
Identify the TV  
1 -  Insert the USB flash drive into one of the USB
connections of the TV.
2 -  Select  Write to USB  and press  OK . An
identification file is written on the USB flash drive. Download the software  
1 -  Insert the USB flash drive into your computer.
2 -  On the USB flash drive, locate the
file  update.htm  and double click it.
3 -  Click  Send ID .
4 -  If new software is available, download the .zip
file.
5 -  After the download, unzip the file and copy the
file  autorun.upg  onto the USB flash drive. Do not
place this file in a folder.
Update the TV software  
1 -  Insert the USB flash drive into the TV again. The
update starts automatically.
2 -  A software update can take several minutes. Do
not press the 
  key on the TV or remote control. Do
not remove the USB flash drive.
3 -  When the update is done, the TV will return to the
channel you were watching. 
If a power cut occurs during the update, never
remove the USB flash drive from the TV. When the
power returns, the update will continue.
To prevent an accidental update of the TV software,
delete the autorun.upg file from the USB flash drive.
25.2
Software Version
To view the current TV software version…
1 -  Press 
 , select  All Settings  and press  OK .
2 -  Select  Update Software  >  Current Software
Info  and press  OK .
3 -  The version, release notes and creation date are
shown. Also, the Netflix ESN Number is shown if
available.
4 -  Press 
  (left) repeatedly if necessary, to close
the menu.
25.3
Open Source Software
This television contains open source software. TP
Vision Europe B.V. hereby offers to deliver, upon
request, a copy of the complete corresponding
source code for the copyrighted open source
software packages used in this product for which such
offer is requested by the respective licences.
This offer is valid up to three years after product
purchase to anyone in receipt of this information.
To obtain the source code, please write in English to .
. .
Intellectual Property Dept.
TP Vision Europe B.V.
Prins Bernhardplein 200
1097 JB Amsterdam
80