Philips 32pfl3406h User Manual

							26
Step 2: Download and update the 
latest software version
1 Connect a USB storage device. 
2 Press . 
3 Select  [Setup] > [Update software].
4 Follow the instructions to load a file onto 
your USB storage device. 
5 Connect the USB storage device to your 
computer, then double-click the file. 
 
» A Web page is launched.
6 Follow the instructions in the Web page.
•  If the current software version 
matches the latest software update 
file, you do not need to update your 
TV software.
•  If the current software version is 
smaller than the latest software 
update file, download the latest 
software update file to the root 
director y of your USB device.
7 Disconnect the USB storage device from 
the computer.
Step 3: Update the TV software
1 Connect your USB storage device to the 
T V.
 
» The TV detects the USB flash drive and 
star ts to scan for software version.
2 If a message prompts you to update the 
software, follow the on-screen instructions 
to update the TV software.
3 If the message is not displayed, continue 
with the following steps: 
4 Press .
5 Select  [Setup] > [Software settings]  > 
[Local updates] .
6 Select the file that you downloaded, then 
press OK to update the TV software 
manually.
7 Follow the on-screen instructions to 
complete the update.
8 To exit, press .
Update the TV software
Philips continuously tries to improve its 
products and we recommend that you update 
the TV software when updates are available.
Ways to update the TV software
You can update the TV software in one of the 
following ways: 
A: with a USB storage device,
B: when prompted through digital broadcasts, or
C: after being prompted through digital 
broadcasts.
A: Update with a USB device
To update with a USB storage device, you need:
•  An empty USB flash drive. The USB flash 
drive must be FAT or DOS-formatted. Do 
not use a USB hard drive.
•  A computer with Internet access
•  An archive utility that suppor ts the ZIP 
file format (for example, WinZip® for 
Microsoft® Windows® or Stufflt® for 
Macintosh®).
Step 1: Check the current software 
version
1 Press . 
2 Select  [Setup] > [Software settings]  > 
[Current software inf].  
» The current software information is 
displayed.
3 Write down the software version number.
4 To return, press  OK.
5 To exit, press .
EN
 
						

							27
English
Change TV  preferences
Use the preferences menu to customise your 
TV settings.
1 Press .
2 Select [Setup] > [TV settings]  > 
[Preferences].
3  Select one of the following, then press  OK.
•  [Menu language] : Select a menu 
language.
•  [Sleep timer]: Switch the TV to 
standby after a pre-defined duration.
•  [Location]: Optimise TV settings for 
your location - home or shop.
•  [E-sticker]: (For shop mode only) 
Switch the e-sticker on or off.
•  [Volume bar]: Display the volume bar 
when you change the volume. 
•  [Auto switch off]: To conser ve energy, 
set the TV to switch to standby 
automatically after a period of 
inactivity. 
This TV is also designed with other 
energy efficiency settings. If there is 
no user interaction (such as pressing 
a remote control button or a control 
on the front panel) for four hours, 
the TV will automatically switch to 
standby.
•  [Channel information size] : Change 
the type of information that is 
displayed when you switch channels. 
•  [Universal access] : Enable or disable 
the universal access menu.
•  [Key beep]: Enable audio feedback 
when you press buttons on the 
remote control or TV.
•  [Audio out delay]: Automatically  sync 
the image on your TV to the audio 
from a connected home theatre.
•  [TV position]: Apply the best settings 
for your TV based on how it is 
mounted.
•  [Teletext 2.5]: Enable or disable 
Teletext 2.5. (For digital TV)
•  [Clock]: Display or remove the time 
from the TV, and set clock options. 
B: Update when prompted through 
digital broadcasts
If you receive digital broadcasts (DVB-T), your 
TV can automatically receive software updates. 
When your TV receives a software update, it 
will prompt you to update the TV software. 
1 Press .
2 Select  [Setup] > [Software settings]  > 
[Announcement] .
3  If a message appears to prompt you 
to update your software, follow the 
instructions to star t the update.
 
» The TV restar ts after the software 
update is complete.
4 If you do not want to update the software, 
select [Setup] > [Software settings]  > 
[Clear announcement] , then press OK.
Note
 
•
If you skip the update, you can update it manually later 
(see ‘C: Check for updates through digital broadcasts’ 
on page 27).
C: Check for updates through digital 
broadcasts
You can check if there are updates available 
through digital broadcasts. 
1 Press .
2 Select  [Setup] > [Software settings]  > 
[Check on major updates] .
3 If an update is available, follow the on-
screen instructions to star t the update.
 
» The TV restar ts after the software 
update is complete.
EN
 
						

							28
Start a TV demo
You can use demonstrations to better 
understand the features of your TV. Some 
demos are not available on cer tain models. 
Available demos are displayed in the menu list.
1 While you watch TV, press .
2 Select  [Setup] > [Watch demo] , OK.
3 Select a demo and press  OK to view it.
4 To exit, press .
Reset the TV to factory 
settings
You can restore the default picture and sound 
settings of your TV. The channel installation 
settings remain the same.
1 Press .
2 Select  [Setup] > [TV settings]  > [Factory 
settings] , then press  OK.
3 If you are prompted to enter a code, enter 
the child-lock code (see ‘Set or change 
code’ on page 22).
 
» A confirmation message is displayed.
4 Press  OK to confirm.
EN
 
						

							29
English
1 Press .
2 Select [Setup] > [Search for channels] , 
then press OK.
3 Select  [Reinstall channels], then press  OK.
 
» The countr y menu is displayed.
4 Select your countr y, then press  OK.
 
» The network menu is displayed.
5 Select the network, then press  OK.
•  [Antenna]: For free-to-air antenna or 
digital DVB-T channels.
•  [Cable]: For cable or digital DVB-C 
channels.
6 Follow the onscreen instructions to select 
other options, if any. 
 
» The star t menu for channel search is 
displayed.
7 Select  [Start], then press  OK.
 
» All available channels are stored. 
8 To exit, press  OK.
Update the channel list
You can enable automatic update of channels 
when your TV is in standby mode. The channels 
stored in your TV are updated ever y morning 
according to the channel information in the 
broadcast.
1 Press .
2 Select [Setup] > [Channel settings]  > 
[Channel installation] > [Automatic 
channel update] .
3 Select [On] to enable the automatic 
update or select  [Off] to disable it.
4 To return, press .
6  Install channels
The first time you set up your TV, you are 
prompted to select a menu language and to 
install TV and digital radio channels (if available). 
Afterwards, you can re-install and fine tune 
channels.
Automatically install channels
You can search and store channels automatically.
Note
 
•
If you have not set the child lock code, you may be 
prompted to set the code (see ‘Set or change code’ on 
page 22).
Step 1: Select your menu language
1 Press .
2 Select  [Setup] > [TV settings]  > 
[Preferences] > [Menu language] , then 
press OK.
3  Select a language, then press  OK.
Step 2: Search for channels
When the TV was switched on for the 
first time, a full installation of channels was 
performed. You can run this full installation again 
to set your language, countr y, and install all 
available TV  channels. 
Note
 
•
For selected models, some options are different.
EN
 
						

							30
Step 3: Fine-tune channels
1 Press .
2 Select [Setup] > [Channel settings]  
> [Channel installation] > [Analogue: 
Manual antenna installation] > [Fine-tune], 
then press OK.
3 Press   to fine-tune the channel. 
Manually install digital 
channels
You can search and store digital TV channels 
one at a time.
Note
 
•
If you have not set the child lock code, you may be 
prompted to set the code (see ‘Set or change code’ on 
page 22).
1 Press .
2 Select  [Setup] > [Channel settings]  
> [Channel installation] > [Digital: 
Reception test] > [Find channel], then 
press OK. 
3  Press the  Numeric buttons  to enter the 
channel frequency. 
4 Select  [Search], then press  OK.
5 When the correct channel is located, select 
[Store], then press OK. 
6 To exit, press .
Note
 
•
If the reception is poor, reposition your antenna and 
repeat the procedure. 
 
•If you receive the channel with DVB-C, select  [Symbol 
rate mode]  > [Automatic], unless your cable provider 
supplies you with a specific symbol rate value. 
Manually install analogue 
channels
You can search and store analogue TV channels 
one at a time.
Note
 
•
If you have not set the child lock code, you may be 
prompted to set the code (see ‘Set or change code’ on 
page 22).
Step 1: Select your system
Note
 
•
If your system settings are correct, skip this step.
1 Press .
2 Select  [Setup] > [Channel settings]  
> [Channel installation] > [Analogue: 
Manual antenna installation]  > [System], 
then press OK.
3  Select the correct system for your countr y 
or region, then press  OK.
Step 2: Search and store channels
1 Press . 
2 Select [Setup] > [Channel settings]  
> [Channel installation] > [Analogue: 
Manual antenna installation]  > [Find 
channel], then press  OK.
•  If you know the three-digit frequency 
of the channel, enter it.
•  To search, select  [Search], then press 
OK.
3  When the channel is found, select  [Done], 
then press OK.
•  To store the channel as a new number, 
select [Store as new channel], then 
press OK.
•  To store the channel as the previously 
selected channel, select  [Store 
current channel], then press  OK.
EN
 
						

							31
English
Hide channels
To prevent unauthorised access to channels, 
hide them from the channel list.
1 While you watch TV, press  FIND.
 
» The channel matrix menu is displayed.
2 Select the channel to hide.
3 Press  OPTIONS.
 
» The channel options menu is displayed.
4 Select  [Hide channel], then press  OK.
 
» The channel is marked as hidden. 
Unhide channels
To prevent unauthorised access to channels, 
hide them from the channel list.
1 While you watch TV, press  FIND.
 
» The channel matrix menu is displayed.
2 Press  OPTIONS.
 
» The channel options menu is displayed.
3 Select  [Show hidden channels] , then press 
OK.  
» The hidden channels are displayed. 
4 Select the channel to unhide, then press   
 OPTIONS.
5 Select [Unhide channel], then press  OK.
 
» The channel is no longer marked as 
hidden.
 
» You can access the hidden channel.
6 To exit, press .
Access CAM services
1
 Inser t and activate the CAM (see ‘Inser t 
and activate a CAM’ on page 36). 
2 Press  OPTIONS.
3 Select  [Common interface] .
 
» Applications provided by the digital TV 
ser vice operator are displayed.
Note
 
•
This menu option is available only if the CAM is 
inser ted and activated correctly.
Rename channels
You can rename channels. The name appears 
when you select the channel.
1  While you watch TV, press  FIND.
 
» The channel matrix menu is displayed.
2 Select the channel to rename.
3 Press  OPTIONS.
 
» The channel options menu is displayed.
4 Select  [Rename channel], then press  OK.
5 To display the text input box, press  OK.
6 For each character, select a character, then 
press OK.
•  To select uppercase letters, lowercase 
letters or symbols: In the row below 
the space key, select the respective 
key, then press  OK.
7 When complete, select  [Done], then press 
OK.  
» The text input box closes.
8 In the rename channel menu, select 
[Done], then press OK.
Rearrange channels
After you install channels, you can rearrange the 
order in which they appear.
1 While you watch TV, press  FIND.
 
» The channel matrix menu is displayed.
2 Press  OPTIONS.
 
» The channel options menu appears.
3 Select  [Reorder], then press  OK.
4 Select the channel to rearrange, then press 
OK.
 
» The selected channel is highlighted.
5 Move the highlighted channel to its new 
location, then press  OK.
6 Press  OPTIONS.
7 Select [Done reordering], then press OK.
EN
 
						

							32
b EXT 1 (RGB and CVBS)
Analogue audio and video input from 
analogue or digital devices such as DVD 
players or game consoles.
 
c DIGITAL AUDIO  OUT 
Digital audio output to home theatres and 
other digital audio systems.
 
d SERV. U
For use by ser vice personnel only.
SPDIF OUT
7 Connect devices
This section describes how to connect devices 
with different connectors. For the location of 
these connectors on your TV, see the quick 
star t guide. More examples of connections with 
other devices are provided in the Quick Star t 
Guide.
Note
 
•
You can use different types of connectors to connect a 
device to your TV.
Tip
 
•
After connection, for easy access to your device, add 
it to the home menu: press , then select  [Add new 
device]. 
Back connections
a  TV ANTENNA
Signal input from an antenna, cable or 
satellite.
  
TV ANTENNA
EN
 
						

							33
English
g HDMI 2 (For selected models)
Digital audio and video input from high-
definition digital devices such as Blu-ray 
players.
 
Connections via DVI or VGA require an 
additional audio cable (see ‘Connect a 
computer’ on page 35).
h  EXT 2 (Y Pb Pr and AUDIO L/R) 
Analogue audio and video input from 
analogue or digital devices such as DVD 
players or game consoles.
 
e PC IN (VGA and AUDIO IN) 
Audio and video input from a computer.
 
f HDMI  1 ARC
Digital audio and video input from high-
definition digital devices such as Blu-ray 
players. Also outputs TV audio to other 
EasyLink-compliant devices, such as home 
theatre systems.
 
Connections via DVI or VGA require an 
additional audio cable (see ‘Connect a 
computer’ on page 35).
VGA
VG A
AUDIO INLEFT/RIGHT
VG A/DV I
 
EN
 
						

							34
d HDMIDigital audio and video input from high-
definition digital devices such as Blu-ray 
players.
 
e  (Headphone) 
Stereo audio output to headphones or 
earphones.
f  COMMON INTERFACE
Slot for a Conditional Access Module 
(CAM).
 
Side connections
a AUDIO L/R
Audio input from analogue devices 
connected to  VIDEO.
 
b VIDEO
Composite video input from analogue 
devices such as VCRs.
 
c USBData input from USB storage devices.
 
EN
 
						

							35
English
• HDMI cable and HDMI-DVI adaptor
 
• VGA cable
 
DVI
AUDIO INLEFT/RIGHT
VGA/DV I
VGA
VGA
AUDIO INLEFT/RIGHT
VGA/DV I
Connect a computer
Before you connect a computer to the TV
• Set the screen refresh rate on your 
computer to 60Hz.
•  Select a suppor ted screen resolution on 
your computer. 
Connect a computer with one of the following 
connectors:
Note
 
•
Connections via DVI or VGA require an additional 
audio cable.
•  HDMI cable
 
• DVI-HDMI cable
 
DVI
AUDIO INLEFT/RIGHT
VGA/DV I
EN