Philips 32pf9631d User Manual

							EN
41
Camera, Camcorder, Game
1. Connect your camera, camcorder or game as
shown.
2. Connect to 
VIDEO2and AUDIO L3for
mono equipment. For stereo equipment also
connect 
AUDIO R3.
S-VHS quality with an S-VHS camcorder is
obtained by connecting the S-VHS cables with
the 
S-VIDEOinput 1and AUDIOinputs
3.
Headphone
1. Insert the plug into the headphone socket L
as shown.
2. The headphone impedance must be between 8
and 4000 Ohm. The headphone socket has a
3.5 mm jack.
In the Sound menu select Headphone
volumeto adjust the headphone volume.
USB
See Multimedia browser, p. 34.
To make video and audio connections - Side panel overview
USB1
2
3
Warning: do not connect cable 1and 2
at the same time. This may cause picture
distortion !
Tip: Press ¬on the remote control to
switch off the internal loudspeakers of the TV.
 
						

							42
EN
Pr Pb Y
DIGITAL
AUDIO AUDIO
HDTV & Progressive 
DISPLAY SYNCHRONIZED
480p, 576p, 720p, 1080i
IN
IN L R
EXT3
AUDIO OUTAUDIO
OUTL RDIGITAL
AUDIO
OUT
HDMI 1  HDMI 2  ANTENNA75o ooPC-VGAEXT2 EXT1o oAUDIO IN L/R
Pr Pb YDIGITAL
AUDIO AUDIO
HDTV & Progressive 
DISPLAY SYNCHRONIZED
480p, 576p, 720p, 1080iIN
IN L REXT3
AUDIO OUTAUDIO
OUTL RDIGITAL
AUDIO
OUT
HDMI 1 
HDMI  ETHERNET ANTENNAVGA EXT2 EXT1 AUDIO OUT
DIGITAL
AUDIO
IN
HDMI 2  ANTENNA75o ooPC-VGA AUDIO IN L/Ro o
EXT3
EXT2 EXT1ETHERNET o
AUDIO IN L/RVGA
AUDIO IN L/R
DVI
DVI
DVI
AUDIO IN L/RDIGITAL
AUDIO
IN
CABLE
YPbPr AUDIO
IN
VCR
DVD player
Satellite
receiver
1 DVD recorder - 1 VCR 
2 DVD recorders
2 VCRs
Decoder PC DVI PC - VGA
DVD player
Cable box DVD player
Cable boxCable box
Decoder VCR Digital 
Home Cinema
amplifier
Analog 
Home Cinema
amplifier Analog 
Home Cinema
amplifier
Game console
To make video and audio connections - Rear panel overview
 
						

							EN
43
Connect a VCR or DVD recorder
With a eurocable
1. Connect the aerial cables 1and 2as
shown.
2. Connect the eurocable 3as shown.
3. Make your selection of the source to which
the VCR has been connected in the Installation
menu, Select your connections, p. 29.
With the aerial cable only
1. Connect the aerial cables 1and 2as
shown.
2. Tune in your recorder’s testsignal and store the
testsignal under programme number 0.
See Analogue: manual  installation, p. 26.
See also the handbook of your recorder.
Connect a decoder and a VCR
Connect a eurocable 4to your decoder and
to the special euroconnector of your recorder.
See also the handbook of your recorder.
Warning: do not place your recorder too close to the screen as some recorders may be susceptible
for signals from the display. Keep a minimum distance of 0,5 m from the screen.
Tip: you can also connect your decoder
directly to EXT1or EXT2with a eurocable.RECORDERDECODER
4
ANTENNA EXT2 EXT1
ANTENNA75oEXT2EXT1
2
RECORDER
1
CABLE
3
EXT 1/2
ANTENNA
ANTENNA75oEXT2
RECORDER
1
CABLE
2
 
						

							EN
44
ANTENNA EXT2 EXT1
ANTENNA75oEXT2 EXT1
RECORDER
CABLE
12
RECORDER
3
5
EXT 1/24
Connect two VCRs or VCR and DVD recorder
With eurocables
1. Connect the aerial cables 1and 2as
shown.
2. Connect your VCRs or DVD-recorder to
EXT1and 2with the eurocables 4and 5.
3. Select the equipment you have connected in
the Installation menu, Select your connections,
p. 29, and link it to 
EXT1or 2.
With aerial cables only
1. Connect the aerial cables 1,2and 3 as
shown.
2. Tune in your recorder’s testsignal and store the
testsignal under programme number 0.
See Analogue: manual  installation, p. 26.
See also the handbook of your recorder.
With a eurocable
1. Connect the aerial cables 1and 2as
shown.
2. Connect your satellite receiver to 
EXT1or 2
with a eurocable 3.
3. Select the equipment you have connected in
the Installation menu, Select your connections,
p. 29, and link it to 
EXT1or 2.
With Component Video connectors
See Connect a DVD player, a satellite receiver
or a cable box, p. 46
Connect a satellite receiver
Note: you can not record signals from equipment connected to the YPbPrinput.
EXT2 EXT1
ANTENNA75oEXT2 EXT1
13
EXT 1/2
2
CABLE
 
						

							EN
45
Connect a DVD player, Cable box or game console
Note: in case of any problems, see Annex 5:
Issues referring to connected peripherals with a
HDMI connector, p. 60.
With a HDMI connector
HDMI is the leading new standard for Digital video
and audio interconnection.
1. Connect your equipment with the 
HDMI
connector.
2. Select the equipment you have connected in
the Installation menu, Select your connections,
p. 29, and link it to 
HDMI 1or 2.
Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys.
Connect a DVD player or Cable box 
With a DVI connector
1. Connect the DVI to HDMI cable to one of the
HDMI connectors of your TV 1.
2. Connect the audio cable 2to the 
DIGITAL
AUDIO IN
connector of the TV.
3. Select the equipment you have connected in
the Installation menu, Select your connections,
p. 29 and link it 
HDMI 1or 2.
4. Also select Digital audio inin the same
Connections menu.
Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys.
Note: only a DVD player with DVI with digital
sound can be connected to the HDMI
connector.
HDMI 1/2
HDMI 1  HDMI 2 ooPC-VGA AUDIO IN L/Ro o
HDMI
Pr Pb Y
DIGITAL
AUDIO AUDIO
HDTV & Progressive 
DISPLAY SYNCHRONIZED
480p, 576p, 720p, 1080i
IN
IN L R
EXT3
AUDIO OUTAUDIO
OUTL RDIGITAL
AUDIO
OUT
HDMI 1 
HDMI DIGITAL
AUDIO
IN
HDMI 2 ooPC-VGA AUDIO IN L/Ro o
EXT3
HDMI
DVIDIGITAL
AUDIO
IN
1
2
 
						

							EN
46
Pr Pb Y
DIGITAL
AUDIO AUDIO
HDTV & Progressive 
DISPLAY SYNCHRONIZED
480p, 576p, 720p, 1080i
IN
IN LR
EXT3
AUDIO OUTAUDIO
OUTL RDIGITAL
AUDIO
OUT
1
EXT3 :
YPbPr EXT3 :
AUDIO IN
R / L
3
DVD / STB
2
DIGITAL
AUDIO
IN
Connect a DVD player, a satellite receiver or Cable box 
With Component Video Connectors
1. Connect the three separate component video
cables 1to the YPbPr jacks on the DVD
player and to the Y,Pband Prjacks of 
EXT3
on the TV.
2. Connect the audio cable 2to the digital out
of the equipment and to the 
DIGITAL
AUDIO IN
connector of the TV.
3. Select the equipment you have connected in
the Installation menu, Select your connections,
p. 29. Also select Digital audio inin the same
Connections menu and link it to 
EXT3.
4. In case of a DVD player with analogue audio,
connect the audio cable to the DVD’s audio 
L
and Rjacks and to theL/R AUDIOjack of
EXT33.
5. In case of a cable box and/or a satellite
receiver also connect the cable TV cable and/or
the satellite antenna cable 4and the aerial
cable 5.
Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys.
Notes:
- cables are often colour coded. Connect red to
red, white to white, etc..;
- the labels for the component video sockets may
differ depending on the DVD player connected.
Although the abbreviations may vary, the letters
B and R stand for the blue and red component
signals, respectively, and  Y indicates the
luminance signal. Refer to the DVD player’s
instructions for use for definitions and
connection details;
- to get an optimal viewing, it is advised to switch
your equipment to the highest possible
supported display modes.
Warning: in case you notice scrolling images,
wrong colours or no colour, no picture, or even
combinations of these on your screen, verify if
the connections are done in the correct way and
if the resolution and the signal standard of the
connected equipment are set in the right way.
See the handbook for your equipment.
Pr Pb Y
DIGITAL
AUDIO AUDIO
HDTV & Progressive 
DISPLAY SYNCHRONIZED
480p, 576p, 720p, 1080i
IN
IN LR
EXT3
AUDIO OUTAUDIO
OUTL RDIGITAL
AUDIO
OUT
ANTENNA
ANTENNA75o1
EXT3 :
YPbPr EXT3 :
AUDIO IN
R / L
SAT / STB
2
DIGITAL
AUDIO
IN
CABLE
4
5
3
 
						

							EN
47
Notes:
- only a PC with digital sound can be connected to the HDMIconnection;
- if your PC does not have digital sound output, connect your PC via a VGA connector;
- before connecting your PC to the TV, select your PC monitor settings to a refresh frequency of 
60 Hz;
- supported PC monitor modes:
VGA 640 x 480
SVGA 800 x 600
XGA 1024 x 768
Connect a PC
Pr Pb Y
DIGITAL
AUDIO AUDIO
HDTV & Progressive 
DISPLAY SYNCHRONIZED
480p, 576p, 720p, 1080i
IN
IN LR
EXT3
AUDIO OUTAUDIO
OUTL RDIGITAL
AUDIO
OUT
oPC-VGA AUDIO IN L/Ro
VGA
2 
1
VGA AUDIO in R/L
Pr Pb Y
DIGITAL
AUDIO AUDIO
HDTV & Progressive 
DISPLAY SYNCHRONIZED
480p, 576p, 720p, 1080i
IN
IN L R
EXT3
AUDIO OUTAUDIO
OUTL RDIGITAL
AUDIO
OUT
HDMI 1 
HDMI  AUDIO in L/R
HDMI 2 ooPC-VGA AUDIO IN L/Ro o
EXT3
HDMI
DVI
2
DIGITAL
AUDIO
IN
3
1
PC equipped with a VGA connector:
1. Connect one end of a VGA cable 1to the
video card of the computer and the other end
to the 
VG Aconnector at the bottom of the
TV. Fix the connector firmly with the screws
on the plug.
2. In case of a Multimedia computer, connect the
audio cable 2to the 
AUDIOoutputs of your
computer and to the 
L/R AUDIOinput of the
TV.
3. Select 
VG Ain the Installation menu, Select
your connections, p. 29 and link it to 
VG A.
4. Also select Analogue audio Inin the same
Connections menu.
PC equipped with a DVI connector:
With Digital audio
1. Use a DVI to HDMI cable to connect to one of
the 
HDMIconnector of your TV 1.
2. Connect the audio cable 2to the 
DIGITAL
AUDIO IN
connector of the TV.
3. Select the computer you have connected in the
Installation menu, Select your connections,
p. 29 and link it to
HDMI 1or 2.
4. Also select Digital audio Inin the same
Connections menu.
With Analogue  audio
1. Use a DVI to HDMI cable to connect to the
HDMI 2connector of your TV 1.
2. Connect the audio cable 3to the 
L/R
AUDIO
input of the TV.
3. Select the computer you have connected in the
Installation menu, Select your connections,
p. 29 and link it to
HDMI 2.
4. Also select Analogue audio Inin the same
Connections menu.
 
						

							EN
48
Pr Pb Y
DIGITAL
AUDIO AUDIO
HDTV & Progressive 
DISPLAY SYNCHRONIZED
480p, 576p, 720p, 1080i
IN
IN L R
EXT3
AUDIO OUTAUDIO
OUTL RDIGITAL
AUDIO
OUT
AUDIO OUT
DIGITAL
AUDIO
OUT
DIGITALAUDIOOUT
1
Connect a Home Cinema amplifier
Digital Home Cinema amplifier

						

							EN
49
Use the Common Interface slot
To receive scrambled DTV signals you will need a
CA (Conditional Access) module and a Smart card
provided by the service provider.
A CA module can enable additional services, for
example Pay TV.
Contact your Common Interface service provider
to get more information about these modules.
Although CA module types may vary dependent
on the manufacturer, each one of the CA modules
supports a certain kind of encryption system. Your
TV supports CA modules to work with the DVB-T
standard.
Note that a smart card may only be valid for a
single broadcast channel.
CA modules and smart cards are neither supplied
nor optional accessories from Philips.
The CA module is responsible for the messages
and texts on screen. In case of failure or strange
behaviour, you must call your CI service
broadcaster.
Insert a CA module 

						

							EN
50
Select connected equipment
Before operating your connected equipment you have to make
a selection in the Installation, Select your connections menu,
p. 29.
1. Press the 
MENU/BROWSEkey.
2. Select TV menuand press the cursor right.
3. Select Installation.
4. Press the cursor right.
5. Select Connections.
6. Press the cursor right.
7. Select the input to which the peripheral equipment is
connected.
8. Press the cursor right again to enter the list of types of
peripherals connected to the selected input
9. Select the peripheral equipment with the cursor up/down.
a
Record a TV programme 
You can record a TV programme using your recorders tuner
without affecting your TV.
1. Select the channel number on your recorder.
2. Set your recorder to record.
See the handbook for your recorder.
Note: when recording analogue progammes, switching
channel numbers on your TV does not disturb recording !
Note: to record digital programmes to an analogue recorder, the TV needs to be switched on and
tuned to that digital programes.
Record with your recorder