Philips 221s3s User Manual

							29
4.1 Resolution & Preset Modes
Maximum Resolution
1920 x 1080 at 60 Hz (analog input) 
1920 x 1080 at 60 Hz (digital input)
Recommended Resolution
1920 x 1080 at 60 Hz (digital input)
H. freq (kHz) Resolution V. freq (Hz)
31.47 720x400 70.09
31.47 640x480 59.94
35.00 640x480 66.67
37.86 640x480 72.81
37.50 640x480 75.00
37.88 800x600 60.32
46.88 800x600 75.00
48.36 1024x768 60.00
60.02 1024x768 75.03
63.89 1280x1024 60.02
79.98 1280x1024 75.03
55.94 1440x900 59.89
70.64 1440x900 74.98
65.29 1680x1050 59.95
67.50 1920x1080 60.00
Note
Please notice that your display works best at 
native resolution of 1920 X 1080@60Hz. For 
best display quality,please follow this resolution 
recommendation. 
7HFKQLFDO6SHFL
						

							30
5. Power Management
5.1 Automatic PowerSaving
If you have VESA DPM compliance display card 
or software installed in your PC, the monitor 
can automatically reduce its power consumption 
when not in use. If an input from a keyboard, 
mouse or other input device is detected, 
the monitor will 'wake up' automatically. The 
following table shows the power consumption 
and signaling of this automatic power saving 
feature: 
221S3L
Power Management Definition
VESA Mode  Video H-sync V-sync  Power UsedLED
color
Active ON Yes Yes< 20.1 W 
(typ.)White
Sleep
(Standby)OFF No No < 0.1 W (typ.)White
(blinking) 
Switch Off OFF - - < 0.1 W (typ.) OFF
221S3
Power Management Definition
VESA Mode  Video H-sync V-sync  Power UsedLED
color
Active ON Yes Yes< 37 W   
(typ.)White
Sleep
(Standby) OFF No No < 0.1 W (typ.)White
(blinking) 
Switch Off OFF - - < 0.1 W (typ.) OFF
The following setup is used to measure power 
consumption on this monitor.
vNative resolution: 1920 x 1080
vContrast: 50%
vBrightness: 300 nits (221S3),25O 
nits(221S3L)
vColor temperature: 6500k with full white 
pattern
Note
This data is subject to change without notice. 
5. Power Management
 
						

							31
6. Regulatory Information
Lead-free Product
Lead free display promotes 
environmentally sound recover y 
and disposal of waste from electrical 
and electronic equipment. Toxic 
substances like Lead has been eliminated 
and compliance with European community’s 
stringent RoHs directive mandating restrictions 
on hazardous substances in electrical and 
electronic equipment have been adhered to 
in order to make Philips monitors safe to use 
throughout its life cycle.
Congratulations!
This display is designed for both you and the 
planet!
The display you have just purchased 
carries the TCO Cer tified label. 
This ensures that your display is 
designed, manufactured and tested 
according to some of the strictest quality and 
environmental requirements in the world. This 
makes for a high performance product, designed 
with the user in focus that also minimizes 
the impact on the climate and our natural 
environment.
TCO Cer tified is a third par ty verified program, 
where ever y product model is tested by an 
accredited impar tial test laborator y. TCO 
Cer tified represents one of the toughest 
cer tifications for displays worldwide.
Some of the Usability features of the TCO 
Certified for displays: 
vVisual ergonomics for good image quality 
is tested to ensure top performance and 
reduce sight and strain problems. Impor tant 
parameters are luminance, contrast, 
resolution, black level, gamma cur ve, colour 
and luminance uniformity and colour 
rendering 
vProducts are tested according to rigorous 
safety standards at impar tial laboratories 
vElectric and magnetic fields emissions as 
low as normal household background levels 
vLow acoustic noise emissions (when 
applicable) 
Some of the Environmental features of the 
TCO Certified for displays:  
vThe brand owner demonstrates corporate 
social responsibility and has a cer tified 
environmental management system (EMAS 
or ISO 14001) 
vVer y low energy consumption both in on- 
and standby mode minimize climate impact 
vRestrictions on chlorinated and brominated 
flame retardants, plasticizers, plastics and 
heavy metals such as cadmium, mercur y 
and lead (RoHS compliance) 
vBoth product and product packaging is 
prepared for recycling 
vThe brand owner offers take-back options 
The requirements can be downloaded from our 
web site. The requirements included in this label 
have been developed by TCO Development in 
co-operation with scientists, exper ts, users as 
well as manufacturers all over the world. Since 
the end of the 1980s TCO has been involved 
in influencing the development of IT equipment 
in a more user-friendly direction. Our labeling 
system star ted with displays in 1992 and is 
now requested by users and IT-manufacturers 
all over the world. About 50% of all displays 
worldwide are TCO cer tified.
For more information, please visit 
www.tcodevelopment.com
TCOFF1058 TCO  Document, Ver.  2.1
Technology for you and the planet
6. Regulatory Information
 
						

							32
EPEAT 
(www.epeat.net)
“The EPEAT (Electronic Product 
Environmental Assessment Tool) 
program evaluates computer 
desktops, laptops, and monitors 
based on 51 environmental criteria developed 
through an extensive stakeholder consensus 
process suppor ted by US EPA.
EPEAT system helps purchasers in the public 
and private sectors evaluate, compare and 
select desktop computers, notebooks and 
monitors based on their environmental 
attributes. EPEAT also provides a clear and 
consistent set of performance criteria for the 
design of products, and provides an oppor tunity 
for manufacturers to secure market recognition 
for effor ts to reduce the environmental impact 
of its products.”
Benefits of EPEAT
Reduce use of primar y materials.
Reduce use of toxic materials.
Avoid the disposal of hazardous waste EPEAT’S 
requirement that all registered products meet 
ENERGY STAR’s energy efficiency specifications, 
means that these products will consume less 
energy throughout their life.
CE Declaration of Conformity
This product is in conformity with the following 
standards: 
vEN60950-1:2006 (Safety requirement of 
Information Technology  Equipment). 
vEN55022:2006 (Radio Disturbance 
requirement of Information Technology 
Equipment). 
vEN55024:1998+A1:2001+A2:2003
(Immunity requirement of Information 
Technology Equipment). 
vEN61000-3-2:2006 (Limits for Harmonic 
Current Emission). 
vEN61000-3-3:1995+A1:2001+A2:2005
(Limitation of Voltage Fluctuation and 
Flicker) following provisions of directives 
applicable.
v2006/95/EC (Low Voltage Directive). 
v2004/108/EC (EMC Directive). 
v2005/32/EC (EuP Directive, EC No. 
1275/2008 mplementing Directive 
for Standby and Off mode power 
consumption) and is produced by a 
manufacturing organization on ISO9000 
level.
The product also comply with the following 
standards. 
vISO9241-307:2008 (Ergonomic 
requirement, Analysis and compliance test 
methods for electronic visual displays). 
vGS EK1-2000:2009 (GS mark requirement). 
vprEN50279:1998 (Low Frequency Electric 
and Magnetic fields for Visual Display). 
vMPR-II (MPR:1990:8/1990:10 Low 
Frequency Electric and Magnetic fields). 
vTCO Displays 5.1 (Requirement for 
Environment Labeling of Ergonomics, 
Energy, Ecology and Emission, TCO: Swedish 
Confederation of Professional Employees) 
for TCO  versions.
Energy Star Declaration
(www.energystar.gov)
As an ENERGY STAR®
 Par tner, we 
have determined that this product 
meets the ENERGY STAR®
guidelines for energy efficiency.
Note
We recommend you switch off the monitor 
when it is not in use for a long time.
6. Regulatory Information
 
						

							33
Federal Communications Commission (FCC) 
Notice (U.S. Only)
This equipment has been tested and found 
to comply with the limits for a Class B 
digital device, pursuant to Par t 15 of the 
FCC Rules. These limits are designed to 
provide reasonable protection against 
harmful interference in a residential 
installation. This equipment generates, uses 
and can radiate radio frequency energy 
and, if not installed and used in accordance 
with the instructions, may cause harmful 
interference to radio communications. 
However, there is no guarantee that 
interference will not occur in a par ticular 
installation. If this equipment does cause 
harmful interference to radio or television 
reception, which can be determined by 
turning the equipment off and on, the 
user is encouraged to tr y to correct 
the interference by one or more of the 
following measures:
vReorient or relocate the receiving antenna. 
vIncrease the separation between the 
equipment and receiver. 
vConnect the equipment into an outlet on 
a circuit different from that to which the 
receiver is connected. 
vConsult the dealer or an experienced 
radio/TV technician for help.
Changes or modifications not expressly 
approved by the par ty responsible for 
compliance could void the user's authority 
to operate the equipment.
Use only RF shielded cable that was supplied 
with the monitor when connecting this monitor 
to a computer device. 
To prevent damage which may result in fire or 
shock hazard, do not expose this appliance to 
rain or excessive moisture. 
THIS CLASS B DIGITAL APPARATUS MEETS 
ALL REQUIREMENTS OF THE CANADIAN 
INTERFERENCE-CAUSING EQUIPMENT 
REGULATIONS.
FCC Declaration of Conformity
Declaration of Conformity for Products Marked 
with FCC Logo. 
United States Only
This device complies with Par t 15 of the FCC 
Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any 
interference received, including interference that 
may cause undesired operation. 
Commission Federale de la Communication 
(FCC Declaration)
Cet équipement a été testé et déclaré 
conforme auxlimites des appareils 
numériques de class B,aux termes de 
l'ar ticle 15 Des règles de la FCC . Ces 
limites sont conçues de façon à fourir 
une protection raisonnable contre les 
interférences nuisibles dans le cadre d'une 
installation résidentielle.
CET appareil produit, utilise et peut 
émettre des hyperfréquences qui, si 
l'appareil n'est pas installé et utilisé selon 
les consignes données, peuvent causer des 
interférences nuisibles aux communications 
radio. 
Cependant, rien ne peut garantir l'absence 
d'interférences dans le cadre d'une 
installation par ticulière. Si cet appareil est 
la cause d'interférences nuisibles pour 
la réception des signaux de radio ou de 
télévision, ce qui peut être décelé en 
fermant l'équipement, puis en le remettant 
en fonction, l'utilisateur pourrait essayer de 
corriger la situation en prenant les mesures 
suivantes:
vRéorienter ou déplacer l'antenne de 
réception. 
vAugmenter la distance entre l'équipement 
et le récepteur. 
6. Regulatory Information
 
						

							34 vBrancher l'équipement sur un autre circuit 
que celui utilisé par le récepteur. 
vDemander l'aide du marchand ou d'un 
technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu 
l'approbation des ser vices compétents 
en matière de conformité est susceptible 
d'interdire à l'utilisateur l'usage du présent 
équipement.
N'utiliser que des câbles RF armés pour 
les connections avec des ordinateurs ou 
périphériques. 
CET APPAREIL NUMERIQUE DE LA CLASSE 
B RESPECTE TOUTES LES EXIGENCES DU 
REGLEMENT SUR LE MATERIEL BROUILLEUR 
DU CANADA. 
EN 55022 Compliance (Czech Republic Only)
Polish Center for Testing and Certification 
Notice
The equipment should draw power from a 
socket with an attached protection circuit (a 
three-prong socket). All equipment that works 
together (computer, monitor, printer, and so on) 
should have the same power supply source.
The phasing conductor of the room's electrical 
installation should have a reser ve shor t-circuit 
protection device in the form of a fuse with a 
nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the 
power supply cable must be removed from the 
power supply socket, which should be located 
near the equipment and easily accessible.
A protection mark "B" confirms that the 
equipment is in compliance with the protection 
usage requirements of standards PN-93/T-42107 
and PN-89/E-06251.
6. R egulatory Information
North Europe (Nordic Countries) Information
Placering/Ventilation 
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE 
OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR 
DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation 
ADVARSEL: 
SØRG VED PLACERINGEN FOR, AT 
NETLEDNINGENS STIK OG STIKKONTAKT 
ER NEMT TILGÆNGELIGE. 
Paikka/Ilmankier to 
VAROITUS: 
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO 
VOIDAAN TARVITTAESSA  HELPOSTI 
IRROTTAA PISTORASIASTA. 
Plassering/Ventilasjon 
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ 
DU PASSE PÅ AT KONTAKTENE FOR 
STØMTILFØRSEL ER LETTE Å NÅ.
BSMI Notice (Taiwan Only)
Ergonomie Hinweis (nur Deutschland)
Der von uns geliefer te Farbmonitor entspricht 
den in der "Verordnung über den Schutz vor 
Schäden durch Röntgenstrahlen" festgelegten 
Vorschriften. 
 
						

							35 Auf der Rückwand des Gerätes befindet sich 
ein Aufkleber, der auf die Unbedenklichkeit der 
Inbetriebnahme hinweist, da die Vorschriften 
über die Bauar t von Störstrahlern nach Anlage 
,,,i$EVGHU5
						

							36
7. Customer care and 
warranty
7.1 Philips’ Flat Panel Monitors Pixel 
Defect Policy
Philips strives to deliver the highest quality 
products. We use some of the industr y's most 
advanced manufacturing processes and practice 
stringent quality control. However, pixel or 
sub pixel defects on the TFT Monitor panels 
used in flat panel monitors are sometimes 
unavoidable. No manufacturer can guarantee 
that all panels will be free from pixel defects, 
but Philips guarantees that any monitor with an 
unacceptable number of defects will be repaired 
or replaced under warranty. This notice explains 
the different types of pixel defects and defines 
acceptable defect levels for each type. In order 
to qualify for repair or replacement under 
warranty, the number of pixel defects on a TFT 
Monitor panel must exceed these acceptable 
levels. For example, no more than 0.0004% of 
the sub pixels on a monitor may be defective. 
Fur thermore, Philips sets even higher quality 
standards for cer tain types or combinations 
of pixel defects that are more noticeable than 
others. This policy is valid worldwide.
Pixels and Sub pixels 
A pixel, or picture element, is composed of 
three sub pixels in the primar y colors of red, 
green and blue. Many pixels together form an 
image. When all sub pixels of a pixel are lit, the 
three colored sub pixels together appear as a 
single white pixel. When all are dark, the three 
colored sub pixels together appear as a single 
7. Customer care and warranty
black pixel. Other combinations of lit and dark 
sub pixels appear as single pixels of other colors.
Types of Pixel Defects 
Pixel and sub pixel defects appear on the screen 
in different ways. There are two categories of 
pixel defects and several types of sub pixel 
defects within each categor y. 
Bright Dot Defects
Bright dot defects appear as pixels or sub pixels 
that are always lit or 'on'. That is, a bright dot is 
a sub-pixel that stands out on the screen when 
the monitor displays a dark pattern. There are 
the types of bright dot defects.
One lit red, green or blue sub pixel.
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light Blue)
Three adjacent lit sub pixels (one white pixel).
 
						

							37
7. Customer care and warranty
Note
A red or blue bright dot must be more 
than 50 
percent brighter than neighboring dots while 
a green bright dot is 30 percent brighter than 
neighboring dots.
Black Dot Defects 
Black dot defects appear as pixels or sub pixels 
that are always dark or 'off'. That is, a dark dot is 
a sub-pixel that stands out on the screen when 
the monitor displays a light pattern. These are 
the types of black dot defects.
Proximity of Pixel Defects 
Because pixel and sub pixels defects of the 
same type that are near to one another may be 
more noticeable, Philips also specifies tolerances 
for the proximity of pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement 
due to pixel defects during the warranty period, 
a TFT Monitor panel in a Philips flat panel 
monitor must have pixel or sub pixel defects 
exceeding the tolerances listed in the following 
tables.
   BRIGHT DOT DEFECTS ACCEPTABLE LEVEL
   1 lit subpixel 3
   2 adjacent lit subpixels 1
   3 adjacent lit subpixels (one white pixel) 0
Distance between two bright dot defects* >15mm
   Total bright dot defects of all types 3
   BLACK DOT DEFECTS ACCEPTABLE LEVEL
   1 dark subpixel 5 or fewer
   2 adjacent dark subpixels 2 or fewer
   3 adjacent dark subpixels 0
Distance between two black dot defects* >15mm
   Total black dot defects of all types 5 or fewer
   TOTAL DOT DEFECTS ACCEPTABLE LEVEL
    Total bright or black dot defects of all types 5 or fewer
Note
1. 1 or 2 adjacent sub pixel defects = 1 dot defect
2. This monitor is ISO9241-307 compliant (ISO9241-307: Ergonomic requirement,analysis and
compliance test methods for electronic visual displays)
 
						

							38
7. Customer care and warranty
7.2 Customer Care & Warranty
For warranty coverage information and additional suppor t requirement valid for your region, please visit 
www.philips.com/suppor t website for details.  You may also contact your local Philips Customer Care 
Center number listed below.
Contact Information for WESTERN EUROPE region:
Country ASC Consumer care number Price
Germany Siemens I&S +49 01803 386 853
€ 0.09
United Kingdom Invec Scotland +44 0207 949 0069  Local call tariff
Ireland Invec Scotland +353 01 601 1161  Local call tariff
Spain Eatsa Spain  +34 902 888 785 
€ 0.10
Finland A-novo  +358 09 2290 1908  Local call tariff
France A-novo +33 082161 1658 
€ 0.09
Greece Allman Hellas +30 00800 3122 1223  Free of charge
Italy A-novo +39 840 320 041 
€ 0.08
Netherlands E Care +31 0900 0400 063
€ 0.10
Denmark  A-novo +45 3525 8761  Local call tariff
Norway  A-novo +47 2270 8250  Local call tariff
Sweden A-novo +46 08 632 0016  Local call tariff
Poland Zolter +48 0223491505  Local call tariff
Austria Siemens I&S +43 0810 000206 
€ 0.07
Belgium E Care +32 078 250851 
€ 0.06
Luxembourg  E Care +352 26 84 30 00  Local call tariff
Por tugal  Eatsa Spain  +351 2 1359 1440  Local call tariff
Switzerland  A-novo +41 02 2310 2116  Local call tariff