Panasonic Wv Ns202 Operating Instructions Manual

							71
•Are you accessing the wrong IP address?
Check the connection as follows:
With the Windows command prompt,
> ping IP address of the camera
When the WV-NS202 replies, the camera is function-
ing normally.
If not, proceed either of the following.
•Restart the camera and change the IP address by
using the Panasonic IP setup software within 20
minutes after the restart.
•Restart the camera while holding the [INITIAL
SET] button on the rear of the camera. The cam-
era will be initialized and the IP address will return
to the default setting 192.168.0.10.
After the camera is initialized, access the camera
and set the IP address again. (When the camera
is initialized, all the settings of the camera previ-
ously configured on the setup menus will be initial-
ized.)
•Are the set IP addresses valid?
•Is the link LED right by the network connector lit?
When it is not lit, connection to a LAN may not be
established or a network may be not working correct-
ly. Check if the cables have any contact failure or if
the wiring is correct or not. 
•Is the LAN cable (category 5) firmly connected to the
network connector on the rear of the camera?
–
68
Troubleshooting
Before asking for repairs, check the symptoms on the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution or if the problem is not
described below.
Reference 
pages Cause/solutionSymptom
Cannot access from the
browser.
Installation
Guide
58
Installation
Guide 
						

							6 •Is the focus adjusted correctly?
Adjust the focus correctly by clicking the focus but-
tons.
•Is there dust or dirt on the lens?
Check if there is dust or dirt on the lens.
•Is Allow selected for FTP access on the [Network]
tab of Network setup page?
If not, select Allow.
•Is the power of the camera on?
Check if the power of the camera is turned on.
•Is the viewer software installed on a PC?
Install the viewer software on a PC.
•Is the version of DirectX 9.0c or later?
Check the version of DirectX as follows.
1. Select Run… from the start menu of Windows
®.
2. Enter dxdiag in the displayed dialog box and
click the [OK] button.
If the version of DirectX is older than 9.0c, upgrade it.
Cannot obtain images on the
SD memory card.
Cannot access from the
browser.
No image is displayed.
Cannot access from the
browser.
Images are displayed blurry.
–
59 Installation
Guide
3, 20
Installation
Guide
–
•Is the entered password correct?
Restart the web browser and enter the password
again.
54
72
•Is the same IP address provided to other devices?
Are there contradictions between the address and the
network subnet to be accessed?

Are the IP addresses of the camera and the PC set in
a common subnet? Or is Use Proxy Server for the
settings of the browser checked?
When accessing the camera in the same subnet, it is
recommended to enter the address of the camera in
the Don’t Use Proxy For These Addresses box.

Is the IP address of the default gateway set for the
camera correct?
–
Reference 
pages Cause/solutionSymptom 
						

							73
•Is any part of the camera worn out?
When the camera does not move to the exact position
frequently, the driving parts may be worn out. Contact
the dealer for assistance.
•When the camera position is moved from the preset
position after turning on the power of the camera,
execute the refresh position function from the
[Initialization] tab of the Maintenance page.
•If the camera always moves to a specific position after
turning on the power of the camera, register that posi-
tion as the home position when convenient. The cam-
era will automatically move to the registered position
using the self return function when turning on the
power of the camera.
•Depending on the traffic of the network or the concen-
tration of access to the camera, there might be diffi-
culties displaying the camera picture. Click the reload
button of the browser to request the camera picture to
be refreshed.
•Depending on the version of your browser, there
might be difficulties refreshing the picture and operat-
ing the camera.
It is recommended to use Internet Explorer
®6.0 SP2.
When using Windows®2000, it is recommended to
use Internet Explorer®6.0 SP1.
•When defocusing is caused by the camera position
being moved, carry out the position refresh to correct
the focus. 
68
The image is not being
refreshed.
The camera does not move
onto the preset position
exactly.
The camera does not auto-
matically move to the previ-
ous position when turning on
the power of the camera.
–
68
29 Installation
Guide
Installation
Guide
Reference 
pages Cause/solutionSymptom
Images are displayed blurry.
•Is the brightness setting set at an appropriate level?
Click the [RESET] button of BRIGHTNESS.
•Is the brightness setting set at an appropriate level?
Click the [RESET] button of BRIGHTNESS.
No image is displayed (or too
dark).
Images are displayed
washed out.
7
7 
						

							•Isn’t the SD memory card out of order?
There are limited times to overwrite on an SD memory
card. When frequently overwritten, it may be at the
end of product life. It is recommended to replace the
SD memory card. 
•Is the viewer software installed on the PC?
Confirm that the viewer software Network Camera
View3 is installed.3, 20
Installation
Guide
74
•Check the settings for the self return function.
•Are the microphone and the speaker connected cor-
rectly and firmly?
Confirm that they are connected correctly and firmly.
•Is ON selected for Super Dynamic 3 ?
Set to OFF.
•When flickers appear frequently, set the shutter speed
to AUTO or 1/100. 
•Are objects hard to focus on with the auto focus func-
tion?
Adjust the focus manually.
•Is there dust or dirt on the transparent part (over the
lens) of the dome cover (camera shell)?
Clean the transparent part of the dome cover.
Cannot adjust the focus cor-
rectly.
Installation
Guide
Reference 
pages Cause/solutionSymptom
6
Flicker appears on the
screen.
The AUTO MODE (OFF,
home position, auto track,
auto pan, preset sequence)
of the camera changes.
Cannot transmit audio to the
camera.
32
29
33
•Is the SD memory card inserted correctly?
•Is the SD memory card formatted?
•Isn’t the write protect switch set to LOCK?
When the write protect switch is set to LOCK, avail-
able size/total size indication of the SD memory card
will be **********KB/**********KB.
Installation
Guide
23
23
–
Installation
Guide
Images cannot be saved on
the SD memory card. 
						

							•Are images displayed on a full screen?
Audio will not be transmitted when displaying images
on a full screen.
•Press the [F5] key on the keyboard of the PC or click
the [Live] button.
7
5 •Is the viewer software installed on the PC?
Confirm that the viewer software Network Camera
View3 is installed.
•Is the OS in use Windows®2000 Professional SP4?
This occurs when using Windows®2000 Professional
SP4.
When it is inconvenient, it is recommended to operate
on Windows
®XP Professional SP2 or Windows®XP
Home Edition SP2.
75
Cannot transmit audio to the
camera.
Cannot return to the Live
page by pressing the [Esc]
key when displaying images
on a full screen.
No live image is displayed.
The alarm occurrence indica-
tion button, the receiver but-
ton, the transmission button,
the AUX buttons and the SD
recording status indicator on
the Live page do not dis-
play the current status in real
time.
3, 20
Installation
Guide
•Open the Security tab of Internet options… under
Tools on the menu bar of Internet Explorer. Then,
add the IP address of the camera to Trusted sites.
•Wasn’t the [Esc] key pressed before images are dis-
played?
Close the browser window by pressing the [Alt] key
and [F4] key simultaneously, etc.
Unnecessary title bar is dis-
played when displaying
images on a full screen.
No image is displayed on a
full screen.
–
7
Reference 
pages Cause/solutionSymptom
20 
						

							76
•This may occur due to the display adapter and driver
combination.
When this has occurred, first update the driver of the
display adapter to the latest version.
If updating the driver does not solve the problem,
adjust the hardware acceleration as follows.
The following are descriptions for when Microsoft XP
Professional SP2 is installed on the PC in use.
(1) Right-click on the desktop and select Properties
from the displayed pop-up menu.
(2) Select Settings from Display Properties, and
then click the [Advanced] button.
(3) Click the [Troubleshoot] tab and disable the
DirectDraw acceleration by adjusting the level of
Hardware acceleration.
–
When displaying MPEG-4
images on two or more
browser windows, images
from two or more cameras
are displayed in sequence
on a single browser window.
Reference 
pages Cause/solutionSymptom 
						

							77
•Click Internet Options on the Tools menu of Internet
Explorer, and then click the [Security] tab. Then, click
the [Custom Level…] button to open the Security
Setting window. Under Miscellaneous, select
Enable for Allow script-initiated windows without
size or position constraints. Click the [OK] button. 
The Warning window will be displayed. Click the
[Yes] button.
•Delete temporary internet files as follows.
1. Select Internet Options… from Tools on the
menu bar of Internet Explorer
®. The Internet
Options window will be displayed.
2. Click the [Delete Files…] button in the Temporary
Internet files section on the [General] tab.
•Click the information bar and select Always Allow
Pop-ups from This Site…. The dialog window saying
Allow pop-ups from this site? will be displayed. Click
the [Yes] button.
•Click the information bar and select Install Active X
Control.
The Security Warning window will be displayed.
Click the Install button on the displayed Security
Warning window.
When using a PC on which Windows®XP Service Pack2 (SP2) is installed
The following may occur during operation when using a PC on which Windows®XP Service Pack2 (SP2) is installed.
Follow the instructions below when the following has occurred. By performing the following solutions, other applica-
tions and the security level may not be affected. 
The Information Bar expressed in the following symptom and solutions will be displayed just below the address bar
only when there is information to communicate. 
The following message is
displayed on the information
bar. 
Pop-up blocked. To see this
pop-up or additional options,
click here…
The following message is
displayed on the information
bar. This site might require
the following Active X control:
nwcv3setup.exe from
Matsushita Electric Industrial
Co., Ltd. Click here to
install...
–
–
Reference 
pages SolutionsSymptom
Information Bar
An unnecessary status bar or
scroll bar is displayed on the
pop-up window. 
Images are not displayed or
refreshed smoothly.
–
– 
						

							78
Directory Structure of Drive B
Drive B
FTP
ALARM060101
060102
File name 01
0123
06010101
06010102
LOCAL
PULLFile name 01
06010101
06010102
00000001
00000001
LOG← Destination where images are to be saved by the SD memory 
recording function of Panasonic network disk recorder
← Destination where log files are to be savedImage failed to transmit to the 
FTP server by the FTP 
periodic tranmission function
(Ex. img_0601010123.jpg)
Image captured at the alarm 
occurrence
(Ex. img_0601010123001.jpg)
Image saved manually
(Ex. img_0601010123001.jpg) 
						

							Panasonic Canada Inc.5770 Ambler Drive,Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
http://www.panasonic.ca
Panasonic Sales Company
Division of Panasonic Puerto Rico Inc.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina
P.R. 00985(809)750-4300
Panasonic System Solutions Company,
Unit Company of Panasonic Corporation of North America
Security Systems
www.panasonic.com/security
For customer support, call 1.877.733.3689
Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094
Zone Office
Eastern:  Three Panasonic Way, Secaucus, New Jersey 07094
Central:  1707 N. Randal Road, Elgin, IL 60123
Southern:  1225 Northbrook Parkway, Suwanee, GA 30024
Western:  6550 Katella Ave., Cypress, CA 90630
© 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.  N0706-1096       3TR004483BAA       Printed in Japan