Panasonic Wireless Speaker System Sc-ne5 Owners Manual

							11
 (ENG) VQT4U55
ENGLISH
With this method you will share the wireless 
network settings of your iPod touch/iPhone/iPad 
with this system.
≥
The following explanations are based on an iPhone.
1Disconnect any devices connected to the CD 
unit.
2Connect the iPhone to your home wireless 
network .
3Connect the  iPhone to the CD unit .
Choose one of the following connections.
“IPOD_DOCK” connection compatible 
iPod touch/iPhone:
iPod touch/iPhone/iPad with iOS 5.0 or later: Connect to the iPod port on the side of the CD 
unit with a dedicated USB cable.
4Unlock your iPhone and then press and hold 
[sNETWORK SETUP]  on the CD unit for more 
than 3 seconds.
≥ If “NOT SUPPORTED” or “SET WI-FI” is displayed, 
check that the iPhone is connected to the wireless 
network and try again from step 1.
5A message will pop-up on your iPhone.
Allow the iPhone to share the wireless network 
settings.*
1
{.The Wi-Fi status indicator blinks.
6The settings are completed when “ SUCCESS” 
is displayed and the Wi-Fi status indicator 
stops blinking  and lights in blue .
7Press [OK] on the remote control to exit the 
settings.
*1: Depending on the network environment or the wireless 
network router settings, it may take more than 10 mins. to 
complete the settings.
Method 2
If youre using an iPod touch/iPhone/iPad.
(iOS version 5.0 or later.)
If “FAIL” is displayed press [OK] and try the 
setting again. If “FAIL” is still displayed, try other 
methods on page 10 or 12.
≥If the iPhone was disconnected midway through, try again 
without disconnecting it.
PP_SC-NE5~VQT4U55_eng.book  11 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							12
VQT4U55 (ENG)
You can make the wireless network settings with 
the app, “Panasonic Stereo System Network Setup” 
(for free).
If you’re using an Android device, download the app 
at Google PlayTM. If you’re using an iPod touch/
iPhone/iPad, download it at the App Store. 
Preparation
≥ Connect your smartphone to your home wireless 
network.
≥ Check the password for your home wireless 
network.
1Press [SETUP] on the remote control repeatedly 
to select “
NET SETUP” and then press [OK].{. “SETTING” is indicated on the display. 
(The Wi-Fi status indicator blinks purple.)
2Sta rt “ Panasonic Stereo System Network 
Setup ” on your smartphone and follow the 
indications.
∫ Note for the iOS version
After step 2
1 Enter the password for the home wireless 
network to which the iOS device is connected.
2 When a message instructing you to connect the  iOS device to this system is displayed, press 
the home button.
3 On the Wi-Fi network selection screen in  “Settings”, select “00 Setup _ _ _ _ _ _”.
≥“ _ ” stands for a digit that is unique to each set.
4 When a message indicating the completion of 
the connection to this system is displayed, 
restart the app.
5 When a message indicating the completion of the Wi-Fi setup of this system is displayed, close the 
app, and then check the operation of AirPlay, etc. 
	≥“Panasonic Stereo System Network Setup” for Mac OS is 
also available at the Mac App Store.
With this method, you will access this system’s 
wireless network settings from the Internet browser 
of your compatible device.
≥The following explanations are based on an 
iPhone.
1Press  [SETUP]  on the remote control 
repeatedly to select “ NET SETUP” and then 
press  [OK].
{.“SETTING” is indicated on the display. 
(The Wi-Fi status indicator blinks purple.)
2After “SETTING” is indicated, connect your 
compatible device to this system’s wireless 
network named “ 00 Setup _ _ _ _ _ _”.
≥“ _ ” stands for a digit that is unique to each set.
≥ Make sure that DHCP is enabled for the network setting 
on your compatible device.
3Start the Internet browser on your compatible 
device and type  “http://192.168.1.12/”  into the 
URL address field and display the page.
{. This system’s setup window is displayed.≥Examples of Internet browsers
iOS device/Mac : Safari
Android device : Google Chrome
TM
PC : Windows Internet Explorer
4Select “ Search wireless network ”.
Method 3
Setting the network connection with the smartphone app.
Method 4
Setting the network connection from an Internet 
browser.
PP_SC-NE5~VQT4U55_eng.book  12 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							13
 (ENG) VQT4U55
ENGLISH
5Select and input the details.
≥Check your  home wireless network name  (Network 
name (SSID)) and  password for this network. This can 
often be found on the wireless network router itself.
6Select “JOIN ” to apply the settings.
≥In the pop-up screen, select “OK” to continue.
– Select “Cancel” to return to the setup window.
7The settings are completed when “ SUCCESS” 
is displayed and the Wi-Fi status indicator 
stops blinking  and lights in blue .
8Make sure to connect your compatible device 
back to your home wireless network .
*1: If you have set your wireless network to be invisible, select 
“BACK” and refer to “Alternative settings”. ≥
The below settings are the alternative or additional settings 
for “Method 4”. 
(l 12)
	≥Enable Java and Cookies in your browser settings.
≥ This system can also be set using the WPS PIN code.
Replace step 2 of “Method 1” with the following steps.
(Before starting, refer to the wireless network router’s 
operating instructions for details on how to enter the PIN 
code.)
1 While “WPS” is flashing press and hold [ s WPS] again 
to display the 8 digit PIN code.
{. Wi-Fi status indicator blinks purple.
2 Enter the PIN code into the wireless network router.
[1] Select your  home wireless network name .*1
[2]Type the password .
If “FAIL” is displayed press [OK], check the 
wireless network password and other settings 
and start again from step 1.
Advanced network settings
Alternative settings
Instead of steps 4 and 5
Select “Manual settings ”.
1 Type your  home wireless network name  
into the “Network name (SSID)” field.
2 Select the  encryption method  from the 
“Security system” drop down list.
3Type the password  into the “Password” field 
and then select “JOIN”.
Additional settings
If your home wireless network has been 
configured to use specific IP Addresses, Subnet 
Mask, Default Gateway, Primary DNS, etc.
Before step 6
Select “Advanced network settings ”.
{.Input the required addresses into each field and select 
“JOIN”.
≥ To change the settings back to DHCP, select “ON” from the 
“DHCP” drop down list.
If you want to change the name of this system 
that is displayed as the AirPlay speakers or DLNA 
renderer.
Before step 4
Select “ Additional settings ”.
1Select “ Edit STEREO SYSTEM name ”.
2 Type a new name into the  “STEREO SYSTEM name” field.
{.Only ASCII characters can be used.
3Select “ OK”.
4 If this system is already connected to your  home wireless network:
jSelect “ Additional settings ” and then 
select “ Exit”.
If this system is not connected to your home 
wireless network:
j Continue to  step 4 of “Method 4”.
PP_SC-NE5~VQT4U55_eng.book  13 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							14
VQT4U55 (ENG)
Using AirPlay with this 
system’s speakers
1Turn this system on.
≥Check that the Wi-Fi status indicator  lights in 
blue .
≥ If it doesn’t light in blue, check the wireless 
network settings. ( l10)
2iOS device: Start the “ Music” (or iPod) app.
Mac/PC: Start “ iTunes”.
≥If the Music app on your iOS device is used, select the 
audio file you want to play.
3Select “Panasonic NE5 _ _ _ _ _ _”*1, 2 from the 
AirPlay  icon.
{. Check the volume settings before starting the playback. 
(When AirPlay is used for the first time, the volume may 
be output at the maximum setting.)
4Start play.≥The playback will start with a slight delay.
	≥This system can be set to turn on automatically when this 
system is selected as the output speakers. ( l22)
≥ Playback of other audio sources will stop and AirPlay output 
will have priority.
≥ Volume changes on the iOS device or iTunes will be applied 
to this system. (Refer to the iTunes Help for the required 
settings in iTunes.)
≥ With some iOS and iTunes versions, it may not be possible 
to restart the AirPlay playback if the selector is changed 
(e.g., “CD”) or this system is turned off, during the AirPlay 
playback.
In this case, select a different device from the AirPlay icon of 
the Music App or iTunes and then re-select this system as 
the output speakers.
≥ AirPlay will not work when playing back videos on iTunes.
*1: “ _ ” stands for a digit that is unique to each set.
*2: The name that is displayed for this system can be changed  from the “Edit STEREO SYSTEM name” settings. 
(
l13, “Advanced network settings”)
With this function set to “ON”, you can stream 
music from the iOS device or 
Mac / PC (iTunes 10.2.2 or later) to this system 
without the need of a wireless network router.
≥Previous network settings will be deleted when 
this function is set to “ON”.
≥ The following explanations are based on an 
iPhone.
1Press [SETUP] repeatedly to select 
“D.CONNECT”.
2Press [ 3,4] to select “ON” and then press 
[OK].
3Press [ 3,4] to select “OK? YES” and then 
press [OK].
4Connect your iPhone to this system’s wireless 
network named “NE5 _ _ _ _ _ _”*2.
5Enter the password that is indicated on this 
system’s display.
6Once the iPhone is connected to this system’s 
wireless network, the setup is competed.
7Continue to step 2 of “Using AirPlay with this 
system’s speakers”.
	≥ This setting is reset to “OFF” when other network settings are 
performed. (l 10)
≥ When “D.CONNECT” is set to “ON”, this system will not be 
connected to the Internet. It is not possible to update the 
software or check the Wi-Fi signal strength.
≥ When AirPlay is not being used, disconnect the AirPlay 
compatible device from this network.
≥ When using a computer on this network, make sure that all 
the shared files are encrypted.
≥ This feature is only compatible with the “Open System” 
authentication method. It is not compatible with “Shared Key” 
authentication method.
*1: “ _ ” stands for a digit.
*2: “ _ ” stands for a digit that is unique to each set.
Preparation
≥ Complete the network settings. ( l10)
≥ Connect the iOS device or Mac/PC to the same 
home wireless network  as this system.
NE5
e.g., 
iPhone iOS 6.0.1
NE5
e.g., 
iTunes 11.0
Directly streaming to this 
system (AirPlay)
“PW _ _ _ _ _”*1 is displayed.
The 5 digits after “PW” is the password for this 
network.
PP_SC-NE5~VQT4U55_eng.book  14 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							15
 (ENG) VQT4U55
ENGLISH
The first time “D.CONNECT” is set to “ON”, a 
password for this system’s wireless network is 
randomly created and memorized in this system.
≥This password is memorized until it is changed.
1 While “D.CONNECT” is set to “ON”: Press [SETUP] repeatedly to select 
“D.CONNECT”.
2Press [ 3,4] to select “ON” and then press 
[OK].
3 The current password is displayed.
≥The 5 digits after “PW” is the password for 
this network.
4 Press any button to exit.
1 While “D.CONNECT” is set to “OFF”: Press [SETUP] repeatedly to select 
“D.CONNECT”.
2Press [ 3,4] to select “CHANGE PW” and 
then press [OK].
3Press [ 3,4] to select “OK? YES” and then 
press [OK].
4 The new password is displayed. ≥The 5 digits after “PW” is the new password 
for this network.
5 Press any button to exit.
∫ Note about changing the password
After changing this system’s wireless network 
password, if you are not prompted to change the 
password on the other devices, the following 
changes are required.
iOS device (iPod touch/iPhone/iPad)*
1:
≥ Before choosing this system’s network, 
1 Select [ ] located beside this system’s 
wireless network name.
2 Select “Forget this Network” and then select  “Forget”.
3 Select this system’s wireless network and enter  the new password.
Mac/PC:
≥ If the computer has memorized the old password, 
be sure to change the memorized password for 
this system’s wireless network to the new one.
	≥ Refer to the devices’s operating instructions for details.
*1: Steps are based on iOS 6.0.1.
Playing back music files on 
the DLNA server
You can share music files stored in the DLNA 
Certified media server (PC with Windows 7 
installed, smartphone, etc.) connected to your 
home wireless network, and enjoy the contents with 
this system’s speaker.
1Turn this system on.
≥ Check that the Wi-Fi status indicator  lights in 
blue .
≥ If it doesn’t light in blue, check the wireless 
network settings. ( l10)
2Operate the DMC compatible device and 
connect to this system.
≥The device name of this system will be 
displayed as “Panasonic NE5 _ _ _ _ _ _”*
1, 2.
≥ For details on how to use DMC compatible 
devices, refer to the operating instructions of 
the devices or the software.
∫ Support format of DLNA client
File formats that are not supported by your DLNA 
server cannot be played.
	≥Depending on the contents and the connected equipment, 
playback may not be possible.
*1: “ _ ” stands for a digit that is unique to each set.
*2: The name that is displayed for this system can be changed  from the “Edit STEREO SYSTEM name” settings. 
(
l13, “Advanced network settings”)
Display the password
Change the password
Preparation
≥Complete the network settings. ( l10)
≥ Connect your device with DMC (Digital Media 
Controller) compatible software installed to the 
same  home wireless network  as this system.
≥
Add the contents and folder to the libraries of the 
Windows Media® Player or the smartphone, etc.– Playlist of Windows Media® Player can play back 
only the contents that are stored in the libraries.
Audio codecExample of file extension
MP3 .mp3
WAV . wav
PP_SC-NE5~VQT4U55_eng.book  15 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							16
VQT4U55 (ENG)
Bluetooth® operations
By using the Bluetooth® connection, you can listen to the sound from the Bluetooth® audio device from this 
system wirelessly.
≥ Refer to the operating instructions of the Bluetooth
® device for details.
Preparation
≥ Turn on the Bluetooth
® feature of the device and 
place the device near the speaker unit.
≥ If this system is already connected to a 
Bluetooth
® device, disconnect it.
1Press [ , AUX] to select “BLUETOOTH”.
≥ If “PAIRING” is indicated on the display, go to step 3.
2Press [PLAY MENU] to select “NEW DEV.” and 
then press [OK].
{.“PAIRING” is indicated on the display.
3Select “SC-NE5” from the Bluetooth® device’s 
Bluetooth® menu.
4Start play on the Bluetooth® device.
	≥ If prompted for the passkey, input “0000”.
≥ You can register up to 8 devices with this system. If a 9th 
device is paired, the device that has not been used for the 
longest time will be replaced.
Preparation
≥Turn on the Bluetooth® feature of the device and 
place the device near the speaker unit.
≥ If this system is already connected to a 
Bluetooth
® device, disconnect it.
1Press [ , AUX] to select “BLUETOOTH”.
{. “READY” is indicated on the display.
2Select “SC-NE5” from the Bluetooth® device’s 
Bluetooth® menu.
{. The name of the connected device is indicated on the 
display for 2 seconds.
3Start play on the Bluetooth® device.
	≥This system can only be connected to one device at a time.
≥ When “BLUETOOTH” is selected as the source, this system 
will automatically try and connect to the last connected 
Bluetooth
® device.
≥ The Bluetooth® device will be disconnected if a different 
audio source (e.g., [CD]) is selected.
You can change the transmission speed to prioritize 
transmission quality or sound quality.
Preparation
≥ Press [ , AUX] to select “BLUETOOTH”.
≥ If a Bluetooth
® device is already connected, 
disconnect it.
1Press [PLAY MENU] repeatedly to select 
“LINK MODE”.
2Press [ 3,4] to select the mode and then 
press [OK].
MODE 1:  Emphasis on connectivity
MODE 2:  Emphasis on sound quality
	≥The default setting is “MODE 1”.
If the sound input level of the Bluetooth® 
transmission is too low, change the input level 
setting.
Preparation
≥ Connect a Bluetooth
® device.
1Press [PLAY MENU] repeatedly to select 
“INPUT LEVEL”.
2Press [ 3,4] to select the level and then press 
[OK].
“LEVEL 0” 
,. “LEVEL i1” ,. “LEVEL i2”
^---------------------------------------------------------J
	≥ Select “LEVEL 0” if the sound is distorted.
≥ The default setting is “LEVEL 0”.
1While a Bluetooth® device is connected:
Press [PLAY MENU] to select 
“DISCONNECT?”.
2Press [ 3,4] to select “OK? YES” and then 
press [OK].
Pairing Bluetooth® devices
Connecting a paired Bluetooth® 
device
Bluetooth® transmission mode
Bluetooth® input level
Disconnecting a Bluetooth® 
device
PP_SC-NE5~VQT4U55_eng.book  16 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							17
 (ENG) VQT4U55
ENGLISH
About Bluetooth®
∫Frequency band used
≥This system uses the 2.4 GHz frequency band.
∫ Certification of this device
≥This system conforms to frequency restrictions 
and has received certification based on 
frequency laws. Thus, a wireless permit is not 
necessary.
≥ The actions below are punishable by law in some 
countries:
– Taking apart or modifying this system.
– Removing specification indications.
∫ Restrictions of use
≥Wireless transmission and/or usage with all 
Bluetooth® equipped devices is not guaranteed.
≥ All devices must conform to standards set by 
Bluetooth SIG, Inc.
≥ Depending on the specifications and settings of a 
device, it can fail to connect or some operations 
can be different.
≥ This system supports Bluetooth
® security 
features. But depending on the operating 
environment and/or settings, this security is 
possibly not sufficient. Transmit data wirelessly to 
this system with caution.
≥ This system cannot transmit data to a Bluetooth
® 
device.
∫ Range of use
≥Use this device at a maximum range of 10 m 
(33 ft). The range can decrease depending on 
the environment, obstacles or interference.
∫ Interference from other devices
≥This system may not function properly and 
troubles such as noise and sound jumps may 
arise due to radio wave interference if this system 
is located too close to other Bluetooth
® devices or 
the devices that use the 2.4 GHz band.
≥ This system may not function properly if radio 
waves from a nearby broadcasting station, etc. is 
too strong.
∫ Intended usage
≥This system is for normal, general use only.
≥ Do not use this system near an equipment or in 
an environment that is sensitive to radio 
frequency interference (example: airports, 
hospitals, laboratories, etc).
Media playback operations
The following marks indicate the availability of the 
feature.
Preparation
≥ Turn this system on.
≥ Insert the media ( l9) or connect the Bluetooth
® 
(l 16) / AirPlay ( l14) compatible device.
≥ Press [CD/RADIO], [iPod] or [ , AUX] to select 
the audio source.
	≥ When using iPod/iPhone/iPad, the operation may vary 
among those models.
[CD] To display information
Press [DISPLAY, iPod MENU] repeatedly.
Panasonic bears no responsibility for data 
and/or information that is compromised 
during a wireless transmission.
[CD]
 : CD audio in CD-DA format ( l5)
[iPod]  : Compatible iPod/iPhone/iPad ( l5)
[AirPlay]  : When connected to an AirPlay 
compatible device. ( l14)
[Bluetooth]  : Connected Bluetooth
® device 
(l 16)
Basic play 
(
[CD], [iPod], [AirPlay], [Bluetooth])
Play Press [1/;].
Stop Press [∫].
Pause Press [1/;].
Press again to restart play.
Skip Press [:/6 ] or [5 /9 ] 
to skip track.
Search(Except [AirPlay])During play or pause
Press and hold [ :/6 ] or 
[ 5 /9 ].
≥Point the remote control at the CD 
unit to opera te.
≥
[iPod] : Backwards search is only 
within the current track.
PP_SC-NE5~VQT4U55_eng.book  17 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							18
VQT4U55 (ENG)
	≥To use this system’s remote control with a Bluetooth® device, 
the Bluetooth® device must support AVRCP (Audio Video 
Remote Control Profile).
Depending on the device or the status of the device, some 
operations may not work.
∫[iPod] To navigate through the iPod/
iPhone menu
≥ Open the Music App to use this feature with iPod touch/
iPhone.
–[ 3, 4] : To navigate menu items.
– [OK] : To go to the next menu.
– [DISPLAY, iPod MENU] : To return to the previous  menu.
	≥ Depending on the model (e.g., iPod nano 7th generation, 
etc.), it may be necessary to select the album, artist, etc. on 
the iPod/iPhone.
Select the playback mode.
1Press [PLAY MENU] to select “REPEAT” or 
“RANDOM” / “SHUFFLE”.
2Press [ 3,4] to select the setting and then 
press [OK].
	≥ When using an iPod/iPhone/iPad or Bluetooth® device, use 
the setting on the device, if available.
≥ During random play, you cannot skip to the previous track.
≥
[CD] : The mode is canceled when you open the door for 
discs.
[AirPlay] : The applied settings will remain until it is 
changed.
*1:[AirPlay] : Perform the settings during playback.
Playback modes ([CD], [AirPlay]*1)
REPEAT
[CD]
OFF Select to cancel repeat playback.
1-TRACK Only plays the selected track.≥ “1, ,  `” is displayed.(Skip to the desired track.)
ALL All tracks are repeated.≥“`” is displayed.
[AirPlay]
Refer to the connected device to verify the 
selected setting.
[CD]  RANDOM
ON Plays the contents randomly.≥“RND” is displayed.
≥ “RND” will not be displayed when 
“1-TRACK” is selected.
OFF Random playback is turned off.
[AirPlay] SHUFFLE
Refer to the connected device to verify the 
selected setting.
PP_SC-NE5~VQT4U55_eng.book  18 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							19
 (ENG) VQT4U55
ENGLISH
Listening to the radio
You can preset up to 30 channels.
Preparation
≥Make sure that the FM antenna is connected. 
(l 8)
≥ Turn this system on.
≥ Press [CD/RADIO] to select “FM”.
	A station previously stored is overwritten when another station 
is stored in the same channel preset.
1Press [PLAY MENU] to select “A.PRESET”.
2Press [ 3,4] to select “LOWEST” or 
“CURRENT” and then press [OK].
LOWEST:
To begin auto preset with the lowest frequency 
(FM 87.9 or FM 87.5).
CURRENT:
To begin auto preset with the current 
frequency.*
*  To change the frequency, refer to “Manual tuning and  presetting”.
The tuner starts to preset all the stations it can 
receive into the channels in ascending order.
Preparation
1 Press [PLAY MENU] repeatedly to select 
“TUNEMODE”.
2 Press [ 3,4] to select “PRESET” and then 
press [OK].
Press [ :/6 ] or [ 5/9 ] to select the 
channel.
∫ Manual tuning and presetting
Select a radio broadcast.
1 Press [PLAY MENU] repeatedly to select 
“TUNEMODE”.
2Press [ 3,4] to select “MANUAL” and then 
press [OK].
3Press [ :/6 ] or [ 5/9 ] to tune to the 
required station.
≥ To start automatic tuning, press and hold [ :/6], 
[ 5 /9] until the frequency starts scrolling. Tuning 
stops when a station is found.
To preset the channel
4 While listening to the radio broadcast
Press [OK].
5Press [ 3,4] to select the channel and then 
press [OK].
∫ To improve FM sound quality
1 While receiving FM broadcasts, press 
[PLAY MENU] repeatedly to select “FM 
MODE”.
2Press [ 3,4] to select “MONO” and then press 
[OK].
≥ This setting can be preset and memorized. To do 
so, continue to step 4 of “Manual tuning and 
presetting”.
	≥ Select “STEREO” in step 2 to return to stereo broadcasts.
≥ “MONO” is canceled if the frequency is changed.
≥ If “MONO” is selected, regardless of the type of signal this 
system is receiving, “FM MONO” is displayed when 
[DISPLAY, iPod MENU] is pressed. ( lbelow)
∫ To display the current signal status
Press [DISPLAY, iPod MENU].
	≥“STEREO” is displayed when this system tunes to a stereo 
broadcast.
Presetting stations 
automatically
Listening to a preset channel
“FM ST”: The FM signal is in stereo.
“FM”: The FM signal is in monaural.
≥“FM” is also displayed even if this system is not tuned to a 
station.
PP_SC-NE5~VQT4U55_eng.book  19 ページ  ２０１３年７月２４日　水曜日　午後２時３６分 
						

							20
VQT4U55 (ENG)
Sound adjustment
The following sound effects can be added to the 
audio output.
1Press [SOUND] repeatedly to select the effect.
2Press [3,4] to select the setting and then 
press [OK].
≥ You may experience a reduction in sound quality when these 
effects are used with some sources. If this occurs, turn the 
sound effects off.
Clock and Timer
To make this setting, point the remote control at 
the speaker unit. 
This is a 12-hour clock.
1Press [SETUP] to select “CLOCK”.
2Press [ 3,4] to set the time and then press 
[OK].
	≥ To display the clock, press [SETUP] to select “CLOCK” and 
then press [OK] once. The time is displayed for 10 seconds.
(During standby, press [DISPLAY, iPod MENU] once.)
≥ The clock is reset when there is a power failure or when the 
AC power supply cord is removed.
≥ Reset the clock regularly to maintain accuracy.
You can set the timer so this system turns on at a 
certain time every day.
Preparation
Set the clock ( lleft).
∫ Setting the timer
1Press [SETUP] repeatedly to select “TIMER ADJ”.
2Press [ 3,4] to set the starting time 
(“ON TIME”) and then press [OK].
3Press [ 3,4] to set the finishing time 
(“OFF TIME”) and then press [OK].
∫ Turn the timer on
1Select the music source*1 and set the desired 
volume.
2Press [SETUP] repeatedly to select “TIMER 
SET”.
3Press [ 3,4] to select “SET” and then press 
[OK].
≥ “F ” is displayed.
≥ To turn the timer off, select “OFF”.
4Press [ Í] to turn this system off.
	≥To display the timer settings, press [SETUP] repeatedly to 
select “TIMER ADJ” and then press [OK] once.
The music source and volume will also be displayed if the 
timer is turned on.
≥ During standby, if the timer is turned on, press [DISPLAY, 
iPod MENU] twice to display the settings.
≥ This system can be used as normal after the timer is set, 
however:
– Turn this system to standby mode before the timer start 
time.
– Even if the audio source or the volume is changed, the 
timer will still use the audio source and volume that was 
set when the timer was turned on.
≥
If this system is having a wireless communication problem at 
the set time, an electronic sound may go off instead of the set 
music source. Turn this system off to stop the electronic sound.
*1: “CD”, “FM”, “AUX”, “IPOD_DOCK” and “IPOD_PORT” can  be set as the music source.
The sleep timer can turn this system off after a set 
time.
1Press [SLEEP] repeatedly to set the time (in 
minutes) and then press [OK].
“SLEEP 30” -. “SLEEP 60” -. “SLEEP 90” -. “SLEEP 120”^------------------------ “OFF” (Cancel) (----------------------b≥ The remaining time is indicated on this system’s display 
except when other operations are performed.
≥ The play timer and sleep timer can be used together. The 
sleep timer always has priority.
Direct-Vocal 
Surround
(D.SURROUND) “LEVEL 1”, “LEVEL 2” or 
“OFF”.
≥
The factory preset is “OFF”.
Preset EQ
(PRESET EQ) “HEAVY” (heavy), “SOFT” 
(soft), “CLEAR” (clear), 
“VOCAL” (vocal) or “FLAT” 
(flat/off).
≥
The factory preset is “HEAVY”.
Bass (BASS) or 
Tr eb le  (TRE BLE ) Adjust the level (
j4 to i 4).
Dynamic Bass
(D.BASS) “ON D.BASS” or 
“OFF D.BASS”.
≥
The factory preset is 
“ON D.BASS”.
Setting the clock
Play timer
Sleep timer
PP_SC-NE5~VQT4U55_eng.book  20 ページ  ２０１３年７月２４日　水曜日　午後２時３６分