Panasonic Ventilation Fv 05vf2 Installation Instructions

READ AND SAVE THESE INSTRUCTIOINS.
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
Applicable to Models: FV-05VF2, FV-08VF2, FV-11VF2
(For Contractor Pack)
Housing Can
FV-05-11VFA2
Motor/Grille Assembly
FV-05VFB2
Table of Contents
2Unpacking
2General Safety Information
IInstallation( Joist Mounting-...

UNPACKING
Unpack and carefully remove unit from carton.
Refer to the following Supplied Accessories list to verify that all parts are present.
GENERAL SAFETY INFORMATION
1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F).oo
2. Make sure that the electric service supply voltage is 120 V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupation
Safety and Health Act (OSHA).
4. Always disconnect the power...

SUPPLIED ACCESSORIES SETS(4 )SUPPLIED ACCESSORIES SETS(4 )
(A) For Motor / Grille Assembly of model: FV-05/08/11VFB2
Quantity Appearance
Part name
Grille4
(B) For Housing Can of model: FV-05-11VFA2
WIRING DIAGRAM
4 24
4
4
8
4
8
4
Thumb screwLong screw
(ST4.2X20)
Suspension
bracketI
Suspension
bracketII
Screw
(ST4.2X8)I
Suspension
bracketIII
Screw
(ST4.2X10)II
3 inches adaptor
connector
(optional part)
Quantity Appearance
Part name
3
OFFPower Supply
AC120V 60Hz
Fan body
Red
Capacitor
WhiteJunction box...

4
INSTALLATION JOIST MOUNTING-II()INSTALLATION JOIST MOUNTING-II()
1. Before installation, Secure the fan body to adaptor by
using thumb screw. (Fig. 1)
Fig. 1
2. Insert the suspension bracket into the fan body and
adaptor. (select the suspension bracket acc rding
to Fig. 2)o
Tape
IMPORTANT:
Adaptor
Remove the tape from damper and adaptor
before installation.As shown below:
Damper
2 Screw (ST4.2X8)I
Suspension bracketIIISuspension bracketII
If spacing A on center joists is 24 inches, connect
suspension...

INSTALLATION JOIST MOUNTING-II( ) CONTINUEDINSTALLATION JOIST MOUNTING-II( ) CONTINUED
5. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig. 5)
6. Refer to wiring diagram (page 3).
Using wire nuts, connect house power wires to
ventilating fan wires:
black to black; white to white; green to green;
Replace the junction box cover. (Fig. 5)
CAUTION:Mount junction box cover carefully so that lead
wires are not pinched. 4. Install the suspension bracket to...

6
INSTALLATION JOIST MOUNTING-II II()INSTALLATION JOIST MOUNTING-II II()
1. Remove adaptor from fan body before starting
installation.
2. Insert the suspension bracket into the adaptor and
secure it to joists by using long screws (ST4.2X20)
(Fig. 7)
Keep the distance B (7/8 inch, 21.6mm) for the
thickness of ceiling board.
3. Follow step 5 to 7 of the Installation (page 5) to
complete the duct work and wiring.I
If spacing A between joists is 21 1/4 to 23 1/2
inches, connect suspension bracket and
(C4...

Fig. 9
INSTALLATION JOIST MOUNTING-II II( ) CONTINUEDINSTALLATION JOIST MOUNTING-II II( ) CONTINUED
6. Secure the fan body to adaptor by using thumb
screw (Fig. 9)
7. Secure to joists by using
long screws (ST4.2X20) and secure it to fan body
by using screw (ST4.2X10) in vertical direction
(Fig. 9)the suspension bracket
II
8. Follow step 8~9 of Installation (page 5) to
complete the installation work.I
INSTALLATION JOIST MOUNTINGIII I-()INSTALLATION JOIST MOUNTINGIII I-()
C1
C2
C3
C44 kinds of -joist...

A13 1/4~15 3/4 ( 336~400 )
16 1/2~18 3/4 ( 419~480 )
B7/8 (21.6)
3~5 ( 76~126 )
5 4/5~7 4/5 ( 148~198 )
Fig.12-1
Fig.12-2
A
Fig. 13
INSTALLATION BETWEEN JOIST MOUNTINGIV()INSTALLATION BETWEEN JOIST MOUNTINGIV()
2. Insert the suspension bracket into the bracket cover of
adaptor side and the back of the fan body. (Fig.12)
(select the suspension bracket according to spacing A
as shown below)
1. Before installation, secure the fan body to adaptor
by using thumb screw. (Fig.1 of page 4)
8
3. Insert the fan...

9
Fig. 16
Fig. 14
Fig. 15
Fig. 17
INSTALLATION WOODEN HEADEV(R)INSTALLATION WOODEN HEADEV(R)
INSTALLATION BETWEEN JOIST MOUNTINGIV( ) CONTINUEDINSTALLATION BETWEEN JOIST MOUNTINGIV( ) CONTINUED
2 Long screws (ST4.2X20)
Joist 4 Long screws
(ST4.2X20)
2 Screw
(ST4.2X10)II
(275)(375)10 7/814 3/4
Adaptor
inches (mm)Fan bodyJoist Header Joist
2. Install header between joists by using nails or screws.
1. Before installation, secure the fan body to adaptor by
using thumb screw. (Fig. 1 of page 4)
4. Secure the...

10
(1) To install the ventilating fan, follow the procedures described in lnstallation . Take the following
precautions before installation.II
1. Installation in existing construction.
Installing the ventilating fan in an existing building requires an accessible area (attic or crawl space) above
the planning installation location or existing ducting and wiring.
CAUTION:
Check area above planning installation location to be sure that:
1. Duct work can be installed and that area is sufficient for proper...