Panasonic Ventilation Fan Fv 08vkl1 Installation Instructions

							Ventilating Fan
SpecificationsDimensions
Description
12 11-12
13-14
14 6-84
4-54 32
2
Table of Contents
Supplied Accessories
Unpacking
General Safety Information
I
Installation( Wooden Header )
10III( -Joist Mounting )I
10-11Installation
( Between Joist Mounting )
Installation( In Existing Construction )VI
Installation( Joist Mounting- )I
Installation
Maintenance
Practical Guide to Installation
14Product Service
FV-08VKL1
8-9II( Joist Mounting- )II Installation
IV
V
READ AND SAVE THESE INSTRUCTIONS.R
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference. 
						

							FV-08VKL1
Quantity Appearance
Part name
Screw
(M4X8)I21
Grille
Suspension
bracketI
Suspension
bracketII
1
1
2Screw
(M4X12)II
Screw
(M4X16)III
2
Machine screw
(M4X8)1
Quantity Appearance
Part name
2
1
1
18W
Fluorescent
lamp
4W
Night lamp
Lighting unit
These Panasonic ceiling mount ventilating fan models use a sirocco fan with dolphin-shaped blades driven by
brushless direct current motor. The motor is designed to have long operating life, high dynamic response, higher
speed ranges with saving eneray. The grille can be quickly detached from the main unit. A damper for preventing
air counterflow is provided. The blower uses a high-capacity sirocco fan developed to reduce the noise level.
The light unit is an energy-saving, lighting device which uses two 18W fluorescent lamps and produces almost
the same illumination as a standard 100W incandescent lamp.
1Suspension
bracketIII
1 8Thumb screwLong screw
(M4X30) 
						

							FV-08VKL1
Junction box cover
Junction box
Lighting unit assy
Fluorescent lamp
Night lamp
Part name No. Part nameNo.
1
2
3
4
5
67
8
9
10
11
Damper Fan bodyAdaptor
Grille
Suspension bracket
Bracket cover
Unit: ( )inches mm
7
3 1/2 (90)1 (25)
5 1/8 130()
7 7/8 200() 13/4 45()
126()
6
13 330()
10 1/4 261()
3 1/2 (90)27/873()
8
9
1110
37/8 98()10 1/4 (261)
12 1/8 (307)
3 1/4 (81)
(For 16 inches on center joists,only use suspension bracket , for 19.2 inches on center joists, only use
suspension bracket , If more than 19.2 inches on center,use suspension bracket & .)I
III II III
13 1/4~15 1/2 ( 336~394 )
16 1/2~18 3/4 ( 419~480 )
21 1/4~23 1/2 ( 540~597 ) 
						

							Specifications are based on HVI standard.
Unpack and carefully remove unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F).oo
2. Make sure that the electric service supply voltage is 120V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code
(NEC) and the Occupation Safety and Health Act (OSHA).
4. Always disconnect the power source before working on or near the fan, motor or light
fixture.
5. Protect the power cord from sharp edges, oil, grease, hot surfaces, chemicals or other
objects.
6. Do not kink the power cord.
7. Do not install the unit where ducts are configured as shown in Fig. A.
8. Provide suction parts with proper ventilation.
9. This unit is approved for use over a bathtub or shower when installed in a GFCI
protected branch circuit.
FV-08VKL1
Noise
(sone) Duct
diameter
(inches)
4
						

							CAUTION:
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig .B)
3. This product must be properly grounded.
Floor
Do not install above or(Cooking area)
inside this area
45o45o
equipmentCooking
Fig. B
WARNING:
To reduce the risk of fire, electric shock or injury to persons, observe the following;
A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact
the manufacturer.
B. Installation work and electrical wiring must be done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated construction.
C. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturers
guideline and safety standards such as those published by the National Fire Protection Association
(NFPA), and the American Society for Heating Refrigeration and Air Conditioning Engineers
(ASHRAE) and the local code authorities.
D. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
E. Ducted fans must always be vented to the outdoors.
F. These models are UL listed for tub and shower enclosures.
G. Solid state controls may cause harmonic distortion which can cause motor humming noise. Do not use
this unit with any solid-state control device.
H. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
I. NEVER place a switch where it can be reached from a tub or shower.
J. Not to be installed in a ceiling thermally insulated to a value greater than R40. 
						

							1. Before installation, secure the fan body to adaptor by
using thumb screw. (Fig.1)
Remove the tape
IMPORTANT :
Adaptor
Remove the tape from damper and adaptor
before installation. As show below:
Damper
2-Screw (M4X8)I
Suspension bracketIIISuspension bracketII
6
Fig.1
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketISuspension
bracketIII
Suspension
bracketI
Fig.2-1
Fig.2-2
Fig.2-3
Fig.2-4Fan body
Fan body
Fan body
Fan body
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketII
Fan body
Thumb screw
2. Insert the supension bracket into the fan body and
adaptor. (select the suspension bracket as show below)
Spacing A on center Joists
Insert Suspension bracket
12 inches
16 inches
19.2 inches vertical joists
24 inchesRefer to Fig. 2-1
Refer to Fig. 2-2
Refer to Fig. 2-3
Refer to Fig. 2-4
If spacing A on center joists is 24 inches, connect
suspension bracket and (C4 mark to C4 mark)
as show below :II III
Joists
A 
						

							Main PCB
Junction box
Fan body
Power supply
AC120V 60Hz
Black
White
Red
Green Black
WhiteLive
Neutral
Ground
M
Black
White
Black
WhiteCurrent Fuse
Electronic
BallastLive
Neutral
Live
Neutral
Wiring diagram
Lighting unit
Black
Red
Blue
Fluorescent
Lamp
Night
Lamp
3.15A
Fig.3-2
Fig.4
4. Install the suspension bracket to joists by using long
screws (M4X30) and secure it to the fan body by
using screw (M4X12) (Fig.4)II
Fan body
Joist
4-Long screws(M4X30)
Joist Fan body
2-Long screws
(M4X30)
2-Long screws
(M4X30)
screw (M4X12)II
7
Junction box cover
Fig. 5
ConduitDuct
5. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig.5)
6. Refer to wiring diagram below.
Using wire nuts, connect house power wires to
ventilating fan wires:
black to black; white to white; green to green;
Replace the junction box cover.
CAUTION:
Mount junction box cover carefully so that lead wires
are not pinched.
7. Install a circular duct and secure it with duct tape or
clamps.
Fig.3-1
Wire nut
Conduit
Junction box
Green wires Lead wires
3. Install the suspension bracket and the flange of fan body
to joists by using long screws (M4X30) ( If spacing A
between joists is 12 inches, install the flange of fan body
according to Fig.3-2, others according to Fig.3-1 to install
the product)
Duct tape
3. Instale la abrazadera de suspension y la brida del cuerpo del
ventilador a las vigas usando los tornillos largos (M4X30)
(Si el espacio A entre las vigas es de mas de 12 pulgadas,
instalar el costado del cuerpo del ventilador siguiendo la
muestra en la Fig. 3-2, para otras dimensiones instale el
producto de acuerdo a la Fig. 3-1) 
						

							3. Follow step 5 to 7 of the installation (page 7) to
complete the duct work and wiring.I
8
9. Insert the plug connector and plug connector
into the receptacle and receptacle respectively,
and secure the light unit to the fan unit with 2 screw
(M4X16) and 1 machine screw (M4X8). (Fig.6)II III
II III
III
10. Insert the fluorescent lamps and screw the night
lamp into the lighting unit.(Fig.6)
11. Insert mouting springs into slots as shown
and mount grille to fan body.(Fig.7)
Fig.6
Plug connectorII
Plug connectorIII
Lighting unit
Screw (M4X16)III
Machine screw
(M4X8)
Plug connectorIII
ReceptacleIII
4 W Night Lamp
Fluorescent lamps
inches (mm)
Slot
Grille Mounting spring
Fig.7
Light unit
Fig.8inches mm()
Joists Adaptor
2-Long screws
(M4X30)
2-Long screws(M4X30)Adaptor
1. Disconnect plug connector from receptacle and
remove adaptor from fan body before starting
installation.
2. Insert the suspension bracket into the adaptor and
secure it to joists by using long screws(M4X30) (Fig.8)
Keep the distance B (7/8 inch, 21.6mm) for the
thickness of ceiling board.
ReceptacleII
8. Finish ceiling work. Ceiling hole should be aligned
with the edge of the flange. (Fig.6)
Plug connectorII
10 7/8(275)
10 7/8(275)
Ceiling
Ceiling
A
Suspension bracket13 1/4~15 1/2 ( 336~394 )
16 1/2~18 3/4 ( 419~480 )
21 1/4~23 1/2 ( 540~597 )
If spacing A between joists is 21 1/4 to 23 1/2
inches (540 to 597mm), connect suspension
bracket and (C4 mark to C4 mark) according
to page 8. Select the suspension bracket
according to spacing A as show below.II III
suspension
bracketsuspension
bracketIsuspension
bracketIIIsuspension
bracket &II III Spacing A
between Joists
inches (mm)13 1/4~15 1/2
(336~394)16 1/2~18 3/4
(419~480)21 1/4~23 1/2
(540~597) 
						

							Make sure that adaptor claws are properly inserted
into body slots.
IMPORTANT:
5. Insert the fan body into joists. (Fig.9)
6. Secure the fan body to adaptor by using thumb
screw and plug connector to receptacle(Fig.10)
Fig. 10Thumb
screwPlug connectorIReceptacleI
Fig. 9
When mounting
body and blower
separately
1. Loosen 3 screws (but
do not remove them
from blower). (Fig.12-1)
2. Remove blower section.
(Fig.12-2)
4. Insert fan body (without
blower section) into joists
(Fig.9)
5. Secure the adaptor to
fan body by using thumb
screw. (Fig.10)
7. Insert the blower into the
fan body. (Fig.12-3)
8. Secure the blower.
(Fig.12-4) and plug
connector to receptacle
(Fig.10) 3. Remove adaptor from
fan body and secure it
to joists as in Fig.8 of
page 8.
Fig.12-2
Fan body
Blower
Fan body
Joist
Fig.12-3
Fig.12-1
Adaptor 3-Screws
Fig.12-4
3-ScrewsScrew driver
SlotsAdaptor
claws Fan body Joist
9
7. Secure to joists by using
long screws(M4X30) and secure it to fan body by
using screw (M4X12) in vertical direction (Fig.11)the suspension bracket
II
8. Follow step 8 to 11 of Installation (page 8) to
complete the installation work.I
2-Long screws
(M4X30)screw (M4X12)II
Fig. 11
Conduit
Junction box cover
Duct4. Insert to fan body (refering
to step 2 of installation , page 6)the suspension bracket in
I
6. Secure the fan body
to joists by using long
screw(M4X30) (Fig.11)
Duct tape 
						

							1. Before installation, secure the to by
using thumb screw (Fig.13) Secure the lighting unit to
fan body (refering to Fig.6 of page 8).fan body adaptor
.
10
Fig.13
Suspension bracket
The suspension can comply with
different kind of joists.III
III
I-bracket
C
2. Connect the suspension to fan body. (Fig.14)
(Select the hole by checking -joist size and fix the
screw to the frame hole.)bracketIII
I
C1
C2
C3
C44 kinds of joist
inches (mm)I-
9/16 ( )14.3
11/16 (17.5)
31/32 (24.6)
1 17/32 38.9()
Thumb screw
Fan body
3. Connect the ventilating fan to the joist. (Fig.15)I-
4. Follow step 5 to 11 of installation (page 7~page 8) to
complete the installation work.I 1. Before installation, secure the to by
using thumb screw (Fig.13) Secure the lighting unit
to fan body (refering to Fig.6 of page 8).fan body adaptor
.
C3
C4
C1
C2
Fig.14
Screw M4X12II ( )
Suspension
bracketIII
Fig.154-Long screws(M4X30)I-joist
Fig.16inches mm()
2. Insert the suspension bracket into bracket cover of
adaptor side and the back of the fan body. (Fig.16)
(select the suspension bracket according to spacing A
as show below)
Suspension bracket
Suspension bracketI
III16 inches and 19.2 inches
horizental joist
19.2 inches vertical joist
Suspension bracket
Suspension bracketIII
II16 inches and 19.2 inches
horizental joist
19.2 inches vertical joistSuspension bracket
Suspension bracketII
I16 inches and 19.2 inches
horizental joist
19.2 inches vertical joist
A
16 inches and 19.2 inches
horizental joist
19.2 inches vertical joist