Panasonic Ventilation Fan Fv 08vkl1 Installation Instructions

Ventilating Fan
SpecificationsDimensions
Description
12 11-12
13-14
14 6-84
4-54 32
2
Table of Contents
Supplied Accessories
Unpacking
General Safety Information
I
Installation( Wooden Header )
10III( -Joist Mounting )I
10-11Installation
( Between Joist Mounting )
Installation( In Existing Construction )VI
Installation( Joist Mounting- )I
Installation
Maintenance
Practical Guide to Installation
14Product Service
FV-08VKL1
8-9II( Joist Mounting- )II Installation
IV
V
READ AND SAVE THESE INSTRUCTIONS.R...

FV-08VKL1
Quantity Appearance
Part name
Screw
(M4X8)I21
Grille
Suspension
bracketI
Suspension
bracketII
1
1
2Screw
(M4X12)II
Screw
(M4X16)III
2
Machine screw
(M4X8)1
Quantity Appearance
Part name
2
1
1
18W
Fluorescent
lamp
4W
Night lamp
Lighting unit
These Panasonic ceiling mount ventilating fan models use a sirocco fan with dolphin-shaped blades driven by
brushless direct current motor. The motor is designed to have long operating life, high dynamic response, higher
speed ranges with saving eneray. The...

FV-08VKL1
Junction box cover
Junction box
Lighting unit assy
Fluorescent lamp
Night lamp
Part name No. Part nameNo.
1
2
3
4
5
67
8
9
10
11
Damper Fan bodyAdaptor
Grille
Suspension bracket
Bracket cover
Unit: ( )inches mm
7
3 1/2 (90)1 (25)
5 1/8 130()
7 7/8 200() 13/4 45()
126()
6
13 330()
10 1/4 261()
3 1/2 (90)27/873()
8
9
1110
37/8 98()10 1/4 (261)
12 1/8 (307)
3 1/4 (81)
(For 16 inches on center joists,only use suspension bracket , for 19.2 inches on center joists, only use
suspension bracket , If...

Specifications are based on HVI standard.
Unpack and carefully remove unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F).oo
2. Make sure that the electric service supply voltage is 120V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code
(NEC) and the Occupation Safety and Health Act (OSHA).
4. Always disconnect the power source...

CAUTION:
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig .B)
3. This product must be properly grounded.
Floor
Do not install above or(Cooking area)
inside this area
45o45o
equipmentCooking
Fig. B
WARNING:
To reduce the risk of fire, electric shock or injury to persons, observe the following;
A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact
the manufacturer.
B....

1. Before installation, secure the fan body to adaptor by
using thumb screw. (Fig.1)
Remove the tape
IMPORTANT :
Adaptor
Remove the tape from damper and adaptor
before installation. As show below:
Damper
2-Screw (M4X8)I
Suspension bracketIIISuspension bracketII
6
Fig.1
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketISuspension
bracketIII
Suspension
bracketI
Fig.2-1
Fig.2-2
Fig.2-3
Fig.2-4Fan body
Fan body
Fan body
Fan body
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketII
Fan...

Main PCB
Junction box
Fan body
Power supply
AC120V 60Hz
Black
White
Red
Green Black
WhiteLive
Neutral
Ground
M
Black
White
Black
WhiteCurrent Fuse
Electronic
BallastLive
Neutral
Live
Neutral
Wiring diagram
Lighting unit
Black
Red
Blue
Fluorescent
Lamp
Night
Lamp
3.15A
Fig.3-2
Fig.4
4. Install the suspension bracket to joists by using long
screws (M4X30) and secure it to the fan body by
using screw (M4X12) (Fig.4)II
Fan body
Joist
4-Long screws(M4X30)
Joist Fan body
2-Long screws
(M4X30)
2-Long screws...

3. Follow step 5 to 7 of the installation (page 7) to
complete the duct work and wiring.I
8
9. Insert the plug connector and plug connector
into the receptacle and receptacle respectively,
and secure the light unit to the fan unit with 2 screw
(M4X16) and 1 machine screw (M4X8). (Fig.6)II III
II III
III
10. Insert the fluorescent lamps and screw the night
lamp into the lighting unit.(Fig.6)
11. Insert mouting springs into slots as shown
and mount grille to fan body.(Fig.7)
Fig.6
Plug connectorII
Plug...

Make sure that adaptor claws are properly inserted
into body slots.
IMPORTANT:
5. Insert the fan body into joists. (Fig.9)
6. Secure the fan body to adaptor by using thumb
screw and plug connector to receptacle(Fig.10)
Fig. 10Thumb
screwPlug connectorIReceptacleI
Fig. 9
When mounting
body and blower
separately
1. Loosen 3 screws (but
do not remove them
from blower). (Fig.12-1)
2. Remove blower section.
(Fig.12-2)
4. Insert fan body (without
blower section) into joists
(Fig.9)
5. Secure the adaptor to
fan...

1. Before installation, secure the to by
using thumb screw (Fig.13) Secure the lighting unit to
fan body (refering to Fig.6 of page 8).fan body adaptor
.
10
Fig.13
Suspension bracket
The suspension can comply with
different kind of joists.III
III
I-bracket
C
2. Connect the suspension to fan body. (Fig.14)
(Select the hole by checking -joist size and fix the
screw to the frame hole.)bracketIII
I
C1
C2
C3
C44 kinds of joist
inches (mm)I-
9/16 ( )14.3
11/16 (17.5)
31/32 (24.6)
1 17/32 38.9()
Thumb screw
Fan...