Panasonic Ventilation Fan Fv 05vs1 Installation Instructions

2 Long screws (M4X30)
Fig. 17
3. Insert the fan body between joists.
Make sure the fan body is level and square
(perpendicular) with the joists. (Fig. 16)
4. Secure the suspension bracket to joists by using long
screws (M4X30). (Fig. 17, Fig. 18)
inches mm()
11
5. Secure the suspension bracket to fan body by using
screw (M4X10). (Fig. 18)II
6. Follow step 5 to 9 of installation (page 7, page 8)
to complete the installation work.I
Adaptor
Fan bodyJoists
Junction box
Fig. 16
Fig. 18
Joist 4 Long screws...

Fig. 20
Fig. 19
(275)(375)10 7/814 3/42. Install header between joists by using nails or screws.
3. Install the ventilating fan and secure it by using long
screws (M4X30). (Fig. 19, Fig. 20)
12
1. Before installation, secure the fan body to adaptor by
using thumb screw. (Fig. 1 of page 6)
4. Follow step 5 to 9 of installation (page 7, page 8) to
complete the installation work.I
(2) Inspect duct work and wiring before proceeding with installation.
(3) Plan suitable location for ventilating fan. (next to...

IMPORTANT:
13
Fig. 21
1. Disconnect plug connector from receptacle and remove
adaptor from fan body before starting installation. (Fig. 22)
2. Insert the suspension bracket into the adaptor. (refer to
step 2 of installation of page 8).II
Fig. 22
Fig. 23
Fig. 25
UP
3. Secure it to stud by using long screws (M4X30). (Fig. 23)
4. Insert the suspension bracket into fan body (refer to
step 2 of installation , page 6I).
6. Complete the duct work and wiring (refer to step 5 to 7
of the installation of page...

Fig. 26
14
2. Insert the suspension bracket into bracket cover of adaptor
side and the back of the fan body (refer to Fig.15-1 of
page 10).
3. Insert the fan body between studs. Make sure the fan body
is level and square(prependicular) with the stud. Ensure
that distance C 3/16 inch (5mm).
4. Secure the suspension bracket to studs by using long
screws (M4X30). (Fig. 26, Fig. 27)
5. Secure the suspension bracket to fan body by using
screw (M4X10) (refere to Fig. 4 of page 7).
6
7. Follow step 7 to 8 of...

5. Complete the duct work and wiring (refer to steps 5 to 7
of the installation on page 7).I
6. Follow step 7 to 8 of the installation to complete
installation work.VII
15
Fig. 29-22-Long screws
(M4X30)
4. Secure the suspension bracket to the wall stud using long
screws (M4X30). Secure the fan body and spacer
to stud using long screws (M4X30). (Fig. 29)
Fig. 29-3
Fan body
Stud
2 Long screws
(M4X30)
Suspension
bracketI
Spacer
Disconnect power source before working on unit. Routine
maintenance must be done...

PANASONIC CONSUMER ELECTRONICS COMPANY
One Panasonic Way, 1H-3 Secaucus, NJ 07094
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga, ON L4W 2T3
Fig. 34
Dryer-hood type vent with
backdraft flap(s).
Caulk termination to duct.
2-3 ft straight run before elbow.
In attic installation,
caulk box to drywall.
Short piece of flexible duct
helps alignment and absorbs
sound. Clamps plus tape at
all flex joints.Foil tape tightly covers
all metal duct joints
(glue PVC joints).
16
3. Remove dust and dirt from fan...