Panasonic Ventilation Fan Fv 05vs1 Installation Instructions

							Ventilating Fan
FV-05VS1
FV-08VS1
READ AND SAVE THESE INSTRUCTIONS.R
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
Description
Dimensions
Specifications
Table of Contents
Supplied Accessories
Unpacking
General Safety Information
4
4-54 32 2
5
Wiring Diagram
13 12 8-9
10
10-11
Installation( In Existing Construction )VI
Installation( Wooden Header )V
16
16Maintenance
Practical Guide to Installation
16Product Service
6-8IInstallation( Joist Mounting- )I
Installation( Joist Mounting- )IIII
( -Joist Mounting )I InstallationIII
Installation
( Between Joist Mounting )IV
14-15
IInstallation( Wall Installation- )IVI
Installation( Wall Installation- )III VII
Installation( Wall Installation- )IIIIX
12
14 
						

							FV-05VS1
FV-08VS1
These Panasonic ceiling mount ventilation fans use a sirocco fan driven by a capacitor motor. The motor
is designed to have an extended service life with reduced energy consumption. It also incorporates a
thermal-cutoff for safety. The grille covering the main body is a spring-loaded, quick-release type. A damper
for preventing counterflow is provided.
1 81Thumb screwLong screw
(M4X30)Quantity Appearance
Part name
Grille
Suspension
bracketI
Suspension
bracketII
1
1
Screw
(M4X8)I2
1Suspension
bracketIII
Screw
(M4X10)II2
Spacer1 
						

							Unit: ( )inches mm
(For 16 inches on center joists, only use suspension bracket . For 19.2 inches on center joists, only use
suspension bracket . If more than 19.2 inches on center joists, use suspension bracket & .)I
III II III
FV-05VS1 FV-08VS1
Junction box cover
Junction box
Motor
Blade
Part name No. Part nameNo.
1
2
3
4
56
7
8
9
10
Damper Fan bodyAdaptor
Grille
Suspension bracketBracket cover
1/2 13()
36/895()
31/8 78()
31/8 78()
11/2 38()
125()23/860()
7
10 1/4 261()
12 300()
3 (76)
13 330()
10 1/4 261( ) 3 3/4 (94)
6
910
8
13 330()13 1/4~15 1/2 336~394
16 1/2~18 3/4 419~480
21 1/4~23 1/2 540~597()
()
() 
						

							Specifications are based on HVI standard.
Unpack and carefully remove unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F).oo
2. Make sure that the electric service supply voltage is 120V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupation
Safety and Health Act (OSHA).
4. Always disconnect the power source before working on or near the fan, motor or junction box.
5. Protect the power cord from sharp edges, oil, grease, hot surfaces, chemicals or other objects.
6. Do not kink the power cord.
7. Do not install the unit where ducts are configured as shown in Fig. A.
8. Provide suction parts with proper ventilation.
9. This unit is UL listed for use over a bathtub or shower when installed in a GFCI protected branch circuit.
Hz
60
V Air direction Model No.
FV-05VS1
FV-08VS1
Exhaust120
(W)
Power consumptionSpeed
(rpm)
4.8 (10.7)
Weight
kgIb.( )
Duct
diameter
(inches)Noise
(sone)
18 350 7590.8
26 3
80 8871.4
Fig. A
Prohibition Prohibition Prohibition ProhibitionAdaptor
4.8 (10.7)
Air deliver
(cfm)
at 0.1 WG. 
						

							CAUTION:
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig. B)
3. This product must be properly grounded.Floor
Do not install above or(Cooking area)
inside this area
45o45o
equipmentCooking
Fig. B
WARNING:
To reduce the risk of fire, electric shock or injury to persons, observe the following:
A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact
to the manufacturer.
B. Installation work and electrical wiring must be done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated construction.
C. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturers
guideline and safety standards such as those published by the National Fire Protection Association
(NFPA), and the American Society for Heating Refrigeration and Air Conditioning Engineers
(ASHRAE) and the local code authorities.
D. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
E. Ducted fans must always be vented to the outdoors.
F. These models are UL listed for tub and shower enclosures.
G. Solid state controls may cause harmonic distortion which can cause motor humming noise. To reduce
the risk of fire or electric shock, do not use this unit with any solid-state control device.
H. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
I. NEVER place a switch where it can be reached from a tub or shower.
J. Not to be installed in a ceiling thermally insulated to a value greater than R40.
Fan body
Red
Capacitor
White
Black
Green
Earth groundJunction box
White
Black
GreenNeutral
Live
EarthPower supply
AC120V 60Hz
Green
K. Install the fan at least 1.5m (5 feet) above the floor, and the fan must be installed above a counter or major
appliances that serves as a barrier.
White 
						

							6
2 Screw (M4X8)I
Suspension bracketIIISuspension bracketII
2. Insert the supension bracket into the fan body and
adaptor. (Select the suspension bracket as shown below)
Spacing A on center joists
Insert Suspension bracket
12 inches
16 inches
19.2 inches vertical joists
24 inchesRefer to Fig. 2-1
Refer to Fig. 2-2
Refer to Fig. 2-3
Refer to Fig. 2-4
If spacing A on center joists is 24 inches, connect
suspension bracket and (C4 mark to C4 mark)
as shown below :II III
Joists
ASuspension
bracketI
Fig.2-1
Fan body
Suspension
bracketISuspension
bracketIII
Fig.2-2
Fan body
Suspension
bracketIII
Suspension
bracketI
Fig.2-3
Fig.2-4Fan body
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketII
Fig.1
Fan body
Remove tape Adaptor
Damper
1. Before installation, secure the fan body to adaptor by
using thumb screw. (Fig.1)
IMPORTANT :
Remove the tape from damper and adaptor
before installation. As shown below:Fan body
Thumb screw 
						

							2 Long screws
(M4X30)
screw (M4X10)II
Fan bodyJoist
2 Long screws
(M4X30)
Joist
4 Long screws (M4X30)Fan body
5. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig. 5)
6. Refer to wiring diagram (page 5).
Using wire nuts, connect house power wires to
ventilating fan wires:
black to black; white to white; green to green;
Replace the junction box cover. (Fig. 5)
CAUTION:Mount junction box cover carefully so that lead
wires are not pinched. 4. Install the suspension bracket to joists by using long
screws (M4X30) and secure it to the fan body by
using screw (M4X10). (Fig. 4)II 3. Install the suspension bracket and the flange of fan
body to joists by using long screws (M4X30) according
to Fig. 3.
7. Install a circular duct and secure it with duct tape
or clamps.
Fig. 4
Fig. 5
Fig. 3-2 Fig. 3-1
A = 10 1/4~12 inches
Junction box coverConduitCircular duct
Wire nut
Conduit
Junction box
Green wires Lead wires
Duct tape 
						

							CAUTION:Joists Adaptor
2 Long screws
(M4X30)
Fig. 7
CeilingSlotMounting spring
Grille
12 1/8(305)
inches mm()Fig. 8
8. Finish ceiling work. Ceiling hole should be aligned
with the edge of the flange. (Fig. 6)
9. Insert mounting springs into slots as shown and
mount grille to fan body. (Fig. 7)
8
1. Disconnect plug connector from receptacle and
remove adaptor from fan body before starting
installation.
2. Insert the suspension bracket into the adaptor and
secure it to joists by using long screws (M4X30). (Fig. 8)
3. Follow step 5 to 7 of the Installation (page 7) to
complete the duct work and wiring.I
If spacing A between joists is 21 1/4 to 23 1/2
inches, connect suspension bracket and
(C4 mark to C4 mark) according to page 6.
Select the suspension bracket according to
spacing A as shown below.II III
suspension
bracketsuspension
bracketIsuspension
bracketIIIsuspension
bracket &II III Spacing A
between Joists
inches (mm)13 1/4~15 1/2
( 336~394 )16 1/2~18 3/4
( 419~480 )21 1/4~23 1/2
( 540~597 )
Fig. 6inches (mm)
4. Insert to fan body
(refering to step 2 of Installation , page 6).the suspension bracket in
I
2 Long screws
(M4X30)
Adaptor
13 1/4~15 1/2 ( 336~394 )
16 1/2~18 3/4 ( 419~480 )
21 1/4~23 1/2 ( 540~597 )Suspension bracket
no more than 1/2 (13)B
A
Ceiling
12 1/8(305)
Ensure that distance B is no more than 1/2 inch (13 mm). 
						

							9
Fig. 9
Fig. 11
2 Long screws
(M4X30)screw (M4X10)II
Conduit
Junction box cover
Circular duct
Joist
Fan body
Adaptor
claws
9
Make sure that adaptor claws are properly inserted
into body slots.
IMPORTANT:
5. Insert the fan body into joists. (Fig. 9)
6. Secure the fan body to adaptor by using thumb
screw and plug connector to receptacle. (Fig. 10)
7. Secure to joists by using
long screws (M4X30) and secure it to fan body by
using screw (M4X10) in vertical direction. (Fig. 11)the suspension bracket
II
8. Follow step 8 to 9 of Installation (page 8) to
complete the installation work.I
Fig.12-1
Adaptor
4 Screws
Fig.12-4
4 Screws
Screw driver
Fig.12-3
Fan body
Fig.12-2
Fan body
Blower
When mounting
body and blower
separately
1. Loosen 4 screws (but
do not remove them
from blower). (Fig. 12-1)
2. Remove blower section.
(Fig. 12-2)
4. Insert fan body (without
blower section) into
joists. (Fig. 9)
5. Secure the adaptor to
fan body by using thumb
screw. (Fig. 10)
7. Insert the blower into the
fan body. (Fig. 12-3) 3. Remove adaptor from fan
body and secure it to
joists as in Fig. 8 of
page 8.
6. Secure the fan body
to joists by using long
screw(M4X30). (Fig. 11)
8. Secure the blower.
(Fig. 12-4) and plug
connector to receptacle.
(Fig. 10)
Fig. 10Thumb
screwPlug connectorI
ReceptacleI
Ceiling
Joist 
						

							10
C1
C2
C3
C44 kinds of -joist
inches (mm)I
9/16 ( )14.3
11/16 (17.5)
31/32 (24.6)
1 17/32 38.9()
Suspension bracket
The suspension can comply with
different kinds of -joist.III
III
I bracket
1. Before installation, Secure the fan body to adaptor by
using thumb screw. (Fig. 1 of page 6)
2. Connect the suspension to fan body. (Fig. 13)
(Select the hole by checking joist size fix the screw
to the frame hole.)bracketIII
I-
3. Connect the ventilating fan to the joist. (Fig. 14)I-
4. Follow step 5 to 9 of installation (page 7, page 8) to
complete the installation work.I
2. Insert the suspension bracket into the bracket cover of
adaptor side and the back of the fan body. (Fig.15)
(select the suspension bracket according to spacing A
as shown below)
1. Before installation, Secure the fan body to adaptor by
using thumb screw. (Fig.1 of page 6)
Fig. 13
Fig. 14
C
C3
C4
C1
C2
Screw (M4X10)II Suspension
bracketIII
4 Long screws
(M4X30)I-joist
16 inches and 19.2
inches horizontal joist
and
19.2 inches vertical joist
A
Suspension bracketI
Suspension bracketIIISuspension bracketII
A = 16 inches and 19.2 inches horizontal joist
Fig.15-1
Suspension bracketIII
A = 19.2 inches vertical joist
Suspension bracketIISuspension bracketIFig.15-2