Panasonic Ventilation Fan Fv 05vf2 Installation Instructions

Ventilating FanFV-05VF2 FV-08VF2 FV-11VF2
READ AND SAVE THESE INSTRUCTIONS.R
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
SpecificationsDimensions
Description
Table of Contents
Supplied Accessories
Unpacking
General Safety Information
Wiring Diagram4
4-54 32
2
5
12 12
13
14 8-9
Installation(...

FV-05VF2
FV-08VF2
FV-11VF2
These Panasonic ceiling mount ventilating fan models use a sirocco fan with dolphin-shaped blades driven by
a capacitor motor. The motor is designed to have an extended service life with reduced energy consumption.
Double orifice technology is used to reduce noise. It also incorporates a thermal-cutoff for safety. The grille
covering the main body is a spring-loaded, quickremove type. A damper for preventing counterflow is provided.
1 81Thumb screwLong screw
(M4X30)Quantity...

Unit: ( )inches mm
Damper
Body Adaptor
Grille
Part name Part name
No. No.
1
2
3
4
67
8
Suspension bracket
Orifice Orifice cover
Bracket cover 59
10 Junction box
Adaptor connector
11
12
Motor Blade
(For 16 inches on center joists, only use suspension bracket , for 19.2 inches on center joists, only use
suspension bracket , If more than 19.2 inches on center,use suspension bracket & .)I
III II III
FV-05VF2
FV-08VF2 FV-11VF2
6 1
24
37/8 98()
3
43/8 110()
5 5/8 (141)
9
10
3 1/4 (81)
1 3/4 (43.5)
2 15/16...

Specifications are based on HVI standard.
Unpack and carefully remove unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F).oo
2. Make certain that the electric service supply voltage is 120V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and
the Occupation Safety and Health Act (OSHA).
4. Always disconnect the power source...

Power Supply
AC120V 60Hz
Fan unit
Red
Capacitor
White
Black
Green
Earth groundJunction box
GreenNeutral
Live
Earth
CAUTION:
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig. B)
3. This product must be properly grounded.Floor
Do not install above or(Cooking area)
inside this area
45o45o
equipmentCooking
Fig. B
WARNING:
To reduce the risk of fire, electric shock or injury to persons, observe the following;
A. Use...

Press and hold the claw of orifice cover to open
the orifice cover.
1. Before installation, open the orifice cover. Secure the fan
body to adaptor by using thumb screw. (Fig. 1)
Fig. 1
2. Insert the supension bracket into the fan body and
adaptor. (select the suspension bracket acc rding
to Fig. 2)o
Remove the tape
IMPORTANT:
Adaptor
Remove the tape from damper and adaptor
before installation.As show below:
Damper
2-Screw (M4X8)I
Suspension bracketIIISuspension bracketII
If spacing A on center joists is...

5. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig. 5)
6. Refer to wiring diagram (page 5).
Using wire nuts, connect house power wires to
ventilating fan wires:
black to black; white to white; green to green;
Replace the junction box cover.
CAUTION:Mount junction box cover carefully so that lead
wires are not pinched. 4. Install the suspension bracket to joists by using long
screws (M4X30) and secure it to the fan body by
using screw (M4X10) (Fig. 4)II...

inches mm()
2-Long screws
(M4X30)Adaptor
Suspension bracket &IIICeiling joist Adaptor
2-Long screws
(M4X30)
Fig. 8
B
A
7/8 (21.6)13 1/4~15 1/2 ( 336~394 )
16 1/2~18 3/4 ( 419~480 )
21 1/4~23 1/2 ( 540~597 )
8. Finish ceiling work. Ceiling hole should be aligned
with the edge of the flange. (Fig. 6)
9. Insert mounting springs into slots as show and
mount grille to fan body. (Fig. 7)
8
Fig. 7
CeilingSlotMounting spring
Grille
1. Open the orifice cover, disconnect plug connector
from receptacle and remove...

Fig. 11
Fig. 10
Fig. 9
When mounting
body and blower
separately
1. Loosen 4 screws (but
do not remove them
from blower). (Fig. 12-1)
2. Remove blower section.
(Fig. 12-2)
4. Insert fan body (without
blower section) into
joists. (Fig. 9)
5. Secure the adaptor to
fan body by using thumb
screw. (Fig. 10)
7. Insert the blower into the
fan body. (Fig. 12-3) 3. Remove adaptor from fan
body and secure it to
joists as in Fig. 8 of
page 8.
9
Make sure that adaptor claws are properly inserted
into body slots....

10
C1
C2
C3
C44 kinds of -joist
inches (mm)I
9/16 ( )14.3
11/16 (17.5)
31/32 (24.6)
1 17/32 38.9()
Suspension bracket
The suspension can comply with
different kinds of -joist.III
III
I bracket
1. Before installation, open the orifice cover. Secure the
fan body to adaptor by using thumb screw. (Fig. 1 of
page 6)
2. Connect the suspension to fan body. (Fig. 13)
(Select the hole by checking joist size fix the screw
to the frame hole.)bracketIII
I-
3. Connect the ventilating fan to the joist. (Fig. 14)I-
4....