Panasonic Ventilating Fan Fv08vsl2 Installation Instructions

FV-08VSL2  
FV-10VSL2 INSTALLATION  INSTRUCTIONS
  
Ventilating Fan
Model No.
READ AND SAVE THESE INSTRUCTIONS Contents
Description
Dimensions General Safety lnformation
Unpacking
Wiring Diagram
lnstallation    (Joist Mounting-  )
lnstallation    (Joist Mounting-   )
lnstallation    (   -Joist Mounting)
lnstallation     (Between Joist Mounting )
lnstallation    (Wooden Header )
lnstallation     (ln Existint Construction )
Maintenance   (cleaning)
Maintenance     (replacement of lamp)
Practical Guide to...

GENERAL SAFETY INFORMATION
2 To reduce the risk of fire, electric shock or injury to persons, observe\
 the following:
9. Do not use this fan with any solid-state speed control device. 2. Before servicing or cleaning unit, switch power off at service panel \
and lock the service 
    disconnecting means to prevent power from being switched on accident\
ally. When the service 
    disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, 
    to the service panel....

GENERAL SAFETY INFORMATION CONTINUED
3
11. USA only: This product has a fluorescent lamp that contains mercury. Disposal may be regulated in 
       your community  due to environmental considerations. For disposal\
 or recycling information, please 
       contact your local authorities or visit Panasonic website: http:/\
/www.panasonic.com/enveronmental 
       or call 1-888-769-0149. 1. Do not install this ventilating fan where interior room temperature m\
ay exceed 104  F (40  C).
2. Make sure that...

FV-08VSL2
     FV-10VSL2 SUPPLIED ACCESSORIES
Part name Part name
Appearance Appearance
Quantity Quantity
Grille
 Suspension
   bracket    Suspension
   bracket  
 Suspension
  bracket  
  Screw
(ST4.2X8) 
  Screw
(ST4.2X12)  1
1
1
1
2
2
  Screw
(ST4.2X16)    Machine screw
        (M4X8) 
        Long screw
        (ST4.2X20) 
        32W
  Fluorescent
        lamp
        4W
 Night lamp
        Lighting unit 2
2
6
1
1
1UNPACKING
Unpack and carefully remove unit from carton.
Refer to the Supplied...

FV-08VSL2
  
FV-10VSL2
FV-10VSL2
WIRING DIAGRAM 6  5/16 (160)
2
3 45
6
713 (330)
5  17/32 (140)
12 (300)
10  1/4 (261)
4  7/10(118.5)
2  7/8 (73)2  3/8 (60)
3  1/4 (82.6)
1   (25)
1011
12
3  6/8 (95) 3  1/8 (78)
3  1/8 (78)
FV-08VSL2 DIMENSIONS
Unit: inches(mm)9
8 10  1/4 (261)
3  3/4 (94)
13 (330) No. Part name
No.Part name
Grille
Fan
Lighting unit
Junction box cover
Adaptor
Fluorescent lamp Fan body
Damper Suspension bracket Junction box Bracket cover Night lamp
7
8
9
10
11
12
1
2
3
4
5
6
(For 16...

lf spacing A on center joists is 24 inches, connect
suspension bracket 
   and    (C4 mark to C4 mark)
as shown below:
2 Screw   (ST4.2X8) Suspension bracket
Suspension bracketINSTALLATION   (JOIST MOUNTING-  )
1. Before installation, secure the fan body to adaptor by
    using machine screw(M4X8). (Fig.1) 
IMPORTANT:
Remove the tape from damper and adaptor 
before installation. As shown below:   Tape
Adaptor Damper2. lnsert the suspension bracket into the fan body and
    adaptor. (Select the suspension...

3. Install the suspension bracket and the flange of fan 
    body to joists by using long screws (ST4.2X20). (If 
    spacing A between joists is 10 1/4~ 12 inches, install 
    the flange of fan body according to Fig.3-2, others 
    according to Fig.3-1 install the product.)
4. Install the suspension bracket to joists by using long
    screws (ST4.2X20) and secure it to the fan body by
    using screw    (ST4.2X12). (Fig.4)
5. Remove junction box cover and secure conduit or 
    stress relief to...

INSTALLATION   (JOIST MOUNTING-  ) CONTINUED8. Finish ceiling work. Ceiling hole should be aligned
    with the edge of the flange. (Fig.6)
9. Insert the plug connector    and plug connector
    into the receptacle    and receptacle     respectively,
    and secure the lighting unit to the fan unit with 2
    screw     (ST4.2X16) and 1 machine screw (M4X8).
    (Fig.6)
10. Insert the fluorescent lamp and screw the night
      lamp into the lighting unit. (Fig.6)
11. Insert mounting springs into slots as...

INSTALLATION    (JOIST MOUNTING-   ) CONTINUED4. Insert the suspension bracket into fan body (refering
    to step 2 of installation   , page 6).
5. Insert the fan body into joists. (Fig.9)
IMPORTANT:Make sure that adaptor claws are properly inserted
into body slots.
6. Secure the fan body to adaptor by using machine
    screw and plug connector to receptacle. (Fig.10)
7. Secure the suspension bracket to joists by using
    long screws (ST4.2X20) and secure it to fan body
    by using screw    (ST4.2X12)...

INSTALLATION     (  
 - JOIST MOUNTING )  4 kinds of   -joist
   inches (mm) hole
mark
C1
C2
C3
C4
9/16 (14.3)
1 17/32 (38.9) 11/16 (17.5)
31/32 (24.6)
C
C1
C3
C4 C2
Suspension bracket
The suspension bracket     can comply with
different kinds of   -joist.
1. Before installation, secure the fan body to adaptor by
    using machine screw (M4X8) (Fig.13). Secure the 
    lighting unit to fan body (refering to Fig.6 of page 8).
2. Connect the suspension bracket     to fan body. (Fig.14)
    (Select the hole...