Panasonic Ventilating Fan Fv08vkml1 Installation Instructions

							3. Follow steps 4 to 6 of the installation (page 9) to
complete the duct work and wiring.I
1. Remove the machine screw by using screw driver,
disconnect plug connector from receptacle and
remove adaptor from fan body before installation.
(Fig.8)
If spacing A between joists is 21 1/4 to 23 1/2
inches (540 to 597mm), connect suspension
bracket and (C4 mark to C4 mark) according
to page. 8 Select the suspension bracket
according to spacing A as shown below.II III
suspension
bracketsuspension
bracketIsuspension
bracketIIIsuspension
bracket &II III Spacing A
between Joists
inches (mm)13 1/4~15 1/2
(336~394)16 1/2~18 3/4
(419~480)21 1/4~23 1/2
(540~597)
11
INSTALLATION JOIST MOUNTING-II II()INSTALLATION JOIST MOUNTING-II II()
Make sure that adaptor claws are properly inserted
into body slots.
IMPORTANT:
5. Insert the fan body into joists. (Fig.10)
4. Insert to fan body (refering
to step 1 of installation , page 8)the suspension bracket in
I
Fig.9inches mm()
Suspension bracket 2 Long screws
(ST4.2X20)
Adaptor Joists 2 Long screws
(ST4.2X20)Adaptor13 1/4~15 1/2 ( 336~394 )
16 1/2~18 3/4 ( 419~480 )
21 1/4~23 1/2 ( 540~597 )
A
Gloves
Gloves
1/2 (12.7)
2. Insert the suspension bracket into the adaptor and
secure it to joists by using long screws (ST4.2X20) (Fig.9)
Keep the distance B (1/2 inch, 12.7mm) for the thickness
of ceiling board.Suspension
bracketI
Fan body
Machine screw
Fig.8
Fig.10
SlotsAdaptor
claws Fan body Joist
Conduit
Junction box cover
Circular duct
Duct tape
Gloves
Screw driver 
						

							2. Connect the suspension to fan body. (Fig.13)
(Select the hole by checking -joist size and fix the
screw to the frame hole.)bracketIII
I
3. Connect the fan body to the joist. (Fig.14)I-
4. Follow steps 4 to 12 of installation (page 9, page 10) to
complete the installation work.I 1. Before installation, secure the lighting unit to fan body
(refering to Fig.5 of page 10).
C
Suspension bracket
The suspension can comply with
different kind of joists.III
III
I-bracket
C3
C4
C1
C2
C1
C2
C3
C44 kinds of joist
inches (mm)I-
9/16 ( )14.3
11/16 (17.5)
31/32 (24.6)
1 17/32 38.9()
INSTALLATION JOIST MOUNTING- CONTINUEDII II()INSTALLATION JOIST MOUNTING- CONTINUEDII II()
12
INSTALLATION JOIST MOUNTINGIII I(- )INSTALLATION JOIST MOUNTINGIII I(- )
7. Secure to joists by using
long screws(ST4.2X20) and secure it to fan body by
using screw (ST4.2X12) in vertical direction (Fig.12)the suspension bracket
II
8. Follow steps 7 to 12 of Installation (page 10) to
complete the installation work.I
Fig.14
4 Long screws (ST4.2X20)I-joist
Fig.13
Screw ST4.2X12() II Suspension
bracketIII
6. Secure the fan body to adaptor by using machine
screw and plug connector to receptacle (Fig.11)
Fig.12
2 Long screws
(ST4.2X20)Screw (ST4.2X12)II
2 Long screws
(ST4.2X20)
Screw driver
Plug connectorIReceptacleI Machine screw
Fig.11 
						

							Suspension bracketI
Suspension bracketIIISuspension bracketII
2. Insert the suspension bracket into bracket cover of
adaptor side and the back of the fan body. (Fig.15)
(select the suspension bracket according to spacing A
as shown below)
A16 inches and 19.2 inches
horizental joist
19.2 inches vertical joist
13
INSTALLATION JOIST MOUNTINGIV( BETWEEN )INSTALLATION JOIST MOUNTINGIV( BETWEEN )
3. Insert the fan body between joists. Make sure the fan
body is level and square (perpendicular) with the joists.
(Fig.16)
4. Secure the suspension bracket to joists by using long
screws(ST4.2X20) (Fig.17, Fig.18)
5. Secure the suspension bracket to fan body by using
screw (ST4.2X12) (Fig.18)II
6. Follow steps 4 to 12 of installation (page 9, page 10)
to complete the installation work.I
Fig.17
2 Long screws (ST4.2X20)
Joist
4 Long screws (ST4.2X20)2 Screw
(ST4.2X12)II
Fig.18
Joists
Fig.16
Junction box Fan bodyAdaptor
inches mm()
A13 1/4~15 3/4 ( 336~400 )
16 1/2~18 3/4 ( 419~480 )
3~5 ( 76~126 )
5 4/5~7 4/5 ( 148~198 )
B
1/2 (12.7)
Fig.15-1
Fig.15-2
Suspension bracketIII
Suspension bracketIISuspension bracketI
16 inches and 19.2 inches
horizental joist
19.2 inches vertical joist
Keep the distance B (1/2 inch, 12.7mm) for the thickness
of ceiling board.
1. Before installation, secure the lighting unit to fan body
(refering to Fig.5 of page 10). 
						

							Wire nut Green wires
Lead wiresRed wires
ConduitJunction boxJunction box
Wire nut Lead wires
Conduit
Green wires
14
INSTALLATION WOODEN HEADEV(R)INSTALLATION WOODEN HEADEV(R)
4. Follow steps 4 to 12 of installation (page 9, page 10)
to complete the installation work.I
3. Install the fan body and secure it by using long
screws(ST4.2X20) (Fig.19, Fig.20)
(275)(375)10 7/814 3/4
Joist Header Joist2. Install header between joists by using nails or screws.
inches (mm)Fig.19
Adaptor
Fan body
INSTALLATION IN EXISTING CONST UCTIONVI(R)INSTALLATION IN EXISTING CONST UCTIONVI(R)
(1) To install the fan body, follow the procedures described in lnstallation . Take the following
precautions before installation.II
1. Installation in existing construction.
Installing the fan body in an existing building requires an accessible area (attic or crawl space) above
the planning installation location or existing ducting and wiring.
(2) Inspect duct work and wiring before proceeding with installation.
(3) Plan suitable location for fan body. (next to ceiling joist)
(5) First, remove ceiling section.
(6) Install fan body.
(1) Inspect duct work and wiring before proceeding with installation.
(2) Remove ceiling section.
(3) Install fan body.
CAUTION:
Check area above the planned installation location to be sure that:
1. Duct work can be done and that area is sufficient for proper ventilation.
2. Wiring can be run to the planned location.
3. No wiring or other obstructions shall interfere with installation.
(4) Before installation, provide inspection and maintenance access at a location that will not interfere
with installation work shown in installation .II
2. Installation from accessible area above fan location.
Fig.20
6 Long screws
(ST4.2X20)Adaptor
Circular duct
1. Before installation, secure the lighting unit to fan body
(refering to Fig.5 of page 10). 
						

							15
MAINTENANCE CLEANINGI()MAINTENANCE CLEANINGI()
Fig.22
4. Remove dust and dirt from fan body using a vacuum
cleaner. (Fig.24)
5. Using a cloth dampened with kitchen detergent, remove
any dirt from fan body. Wipe dry with new cloth. (Fig.25)
6. Replace grille.
Fig.24
Fig.25
Fig.23
3. The grille should be dry after cleaning. (Fig.23)
2. Wash and clean grille. (Use non-abrasive kitchen detergent,
wipe dry with new cloth.) (Fig.22)
MAINTENANCEII(REPLACEMENT OF LAMP)MAINTENANCEII(REPLACEMENT OF LAMP)
1. Disconnect power source before working on unit.
2. The lamps glass is fragile. Please handle with care. To remove lamp, grasp at base and move back
and force to loosen.Do not pull hard on the lamp or you may break the glass.
3. 4W night lamp has threaded base. Remove by turning counterclockwise.
4. Be sure to remove the night lamp before remove fluorescent lamps.
Disconnect power source before working on unit. Routine
maintenance must be done every year.
WARNING:
CAUTION:
1. Never use gasoline, benzene, thinner or any other
such chemicals for cleaning the ventilating fan.
2. Do not allow water to get into the motor.
3. Do not soak resin parts in water over 60 C (140 F).
oo
Glove
Gloves
Vacuum cleaner
GrilleGloves
Sensor unit
Grille
Ceiling
Gloves
Mounting springCeiling
Fig.21-1
Fig.21-2
1. Remove grille pull down one mounting spring. Remove
sensor unit then pull down the other mounting spring.
(Squeeze mounting spring and pull down carefully.) (Fig.21) 
						

							Warning Concerning Removal of Covers.
The unit should be serviced by qualified technicians only. No service information is provided for customers.
Your product is designed and manufactured to ensure a minimum of maintenance. However, should your
unit ever require service, a nationwide system of factory service centers and AUTHORIZED INDEPENDENT
SERVICE CENTERS is maintained to support your products warranty.
(In the U.S.A.,call 1-866-292-7292 to Customer call Center.)
P ODUCT SE VICERRP ODUCT SE VICERR
3. Change the fluorescent lamps (Panasonic FDS
18E27/4,18W or FDS18E35/4, 18W or FDS18E42/4,
18W ) or the 4W night lamp, connect the plug
connector and replace the grille.(Fig.27)II 1. Remove grille. (Squeeze mounting spring and pull
down) (Fig.21 of page 15)
Fig.28
Loose fill or batt insulation can be placed
directly over the fan housing in the attic.
Panasonic fans and fan/light combination
units do not create excessive heat that is
a common problem with recessed light
fixtures or some competitors fan/light
combinations. Our efficient, cool-running
motors and our fluorescent bulbs do not
create enough ambient heat to be subjected
to these limitations.
Proper insulate the area around the fan to
minimize building heat loss and gain. (Fig.28)Dryer-hood type vent with
backdraft flap(s).
Caulk termination to duct.
2-3 ft straight run before elbow.
In attic installation,
caulk box to drywall.
Short piece of flexible duct
helps alignment and absorbs
sound. Clamps plus tape at
all flex joints.Foil tape tightly covers all metal
duct joints (glue PVC joints).Insulation.
P ACTICAL GUIDE TO INSTALLATIONRP ACTICAL GUIDE TO INSTALLATIONR
MAINTENANCEII(REPLACEMENT OF LAMP) CONTINUEDMAINTENANCEII(REPLACEMENT OF LAMP) CONTINUED
X0108-0 08VKML420
PANASONIC CONSUMER ELECTRONICS COMPANY
Division of Panasonic Corporation of North America,
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga, ON L4W 2T3 www.panasonic.com One Panasonic Way, Secaucus, NJ 07094
2. Remove the 4 W night lamp. (Fig.26)
Fig.26
Fig.27
Gloves
www.panasonic.ca