Panasonic Ventilating Fan Fv08vkml1 Installation Instructions

READ AND SAVE THESE INSTRUCTIONS.R
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
15-16
16 8-107
Table of Contents
Unpacking
General Safety Information
14VInstallation( Wooden Header )
12
14
Installation( In Existing Construction )VI
IInstallation( Joist Mounting- )I
III( -Joist Mounting )I...

than the minimum ENERGY STAR requirements.
5
efficient
FV-08VKSL1
FV-08VKML1 only).
ventilating 

These Panasonic ventilating fans use a sirocco fan with dolphin-shaped blades driven by brushless direct
current motor powered by an integral transformer. The motor is designed to have long operating life, high
dynamic response, higher speed ranges with saving energy. The grille can be quickly detached from the main
unit. A damper for preventing air counterflow is provided. The blower uses a high-capacity sirocco fan developed
to reduce the noise level.
SUPPLIED ACCESSORIES UNPACKING
DESCRIPTION
The...

DIMENSIONS
Unit: ( )inches mm
(For 16 inches on center joists, only use suspension bracket , for 19.2 inches on center joists, only use
suspension bracket , If more than 19.2 inches on center, use suspension bracket & .)I
III II III
Junction box cover
Junction box
Lighting unit
Fluorescent lamp
Night lamp
Part name No.Part name
No.
1
2
3
4
5
67
8
9
10
11
Damper Fan bodyAdaptor
Grille
Suspension bracket
Bracket cover
12Sensor unit
FV-08VKSL1 FV-08VKML1
6
13 330()
10 1/4 261()
3 1/2 (90)
8
9
10
37/8 98()10...

SWITCH INDICATION
30
40 50 60 70 80
Delay Time
[min]
WI ING DIAG AMRRWI ING DIAG AMRR
Low speed air-volume preset switch positions
Air Volume
[cfm]
High/Low delay time preset switch positions
0.5
1235
10 2030
60
Factory setting : 20 minutes
Position 0 : Use for factory test only.
0
Factory setting : 50 cfm
Switch indications
on blower unit
Low speed air vol-
ume preset switch High / Low delay time
preset switch
FV-08VKML1
FV-08VKSL1
White
White
Position   use for factory test only.
CFM 

Duct
diameter
(inches)
416.5 7.5()
(cfm)(rpm)
FV-08VKML1
FV-08VKSL1
9.5
7.7
6.5
5.8
5.0
70
60
50
40
30
700
666
647
628
620 

CAUTION:
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig. B)
3. This product must be properly grounded.
45o45o
Floor
Do not install above or(Cooking area)
inside this area
equipmentCooking
Fig. B
3. Follow all local electrical and safety codes, as well as the National Electrical Codethe Occupation Safety and Health Act (OSHA). (NEC) and
4. Always disconnect the power source before working on or near the fan,...

8
2-Screw (ST4.2X8)I
Suspension bracketIIISuspension bracketII
INSTALLATION JOIST MOUNTING-II()INSTALLATION JOIST MOUNTING-II()
1. Insert the suspension bracket into the fan body and
adaptor. (select the suspension bracket as shown below)
Spacing A on center joists
Insert Suspension bracket
12 inches
16 inches
19.2 inches vertical joists
24 inchesRefer to Fig. 1-1
Refer to Fig. 1-2
Refer to Fig. 1-3
Refer to Fig. 1-4
If spacing A on center joists is 24 inches, connect
suspension bracket and (C4 mark to...

Fan body
4 Long screws (ST4.2X20)
Joist
9
Fig.2-2
INSTALLATION JOIST MOUNTING-II( ) CONTINUEDINSTALLATION JOIST MOUNTING-II( ) CONTINUED
3. Install the suspension bracket to joists by using long
screws (ST4.2X20) and secure it to the fan body by
using screw (ST4.2X12) (Fig.3)II
Junction box cover
Fig.4
ConduitCircular duct
4. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig.4)
CAUTION:Mount junction box cover carefully so that lead
wires are not pinched....

10 7/8(275)
10 7/8(275)
Ceiling
Sensor unitGrille
Ceiling
Fig.6-2
Gloves
INSTALLATION JOIST MOUNTING-II( ) CONTINUEDINSTALLATION JOIST MOUNTING-II( ) CONTINUED
8. Insert the plug connector into the receptacle ,
and secure the lighting unit to the fan
body with 1 screw (ST4.2X16) and 2 machine
screws (M4X8). (Fig.5)II II
III
9. Insert the fluorescent lamps and s cure the night
lamp into the lighting unit. (Fig.5)e
12. Insert mounting springs into the slots as shown and
mount grille to fan body....