Panasonic Ventilating Fan Fv 08vkml1, Fv 08vksl1 Installating Instructions

3. Follow steps 4 to 6 of the installation (page 9) to
complete the duct work and wiring.I
1. Remove the machine screw by using screw driver,
disconnect plug connector from receptacle and
remove adaptor from fan body before installation.
(Fig.8)
If spacing A between joists is 21 1/4 to 23 1/2
inches (540 to 597mm), connect suspension
bracket and (C4 mark to C4 mark) according
to page. 8 Select the suspension bracket
according to spacing A as shown below.II III
suspension
bracketsuspension...

2. Connect the suspension to fan body. (Fig.13)
(Select the hole by checking -joist size and fix the
screw to the frame hole.)bracketIII
I
3. Connect the fan body to the joist. (Fig.14)I-
4. Follow steps 4 to 12 of installation (page 9, page 10) to
complete the installation work.I 1. Before installation, secure the lighting unit to fan body
(refering to Fig.5 of page 10).
C
Suspension bracket
The suspension can comply with
different kind of joists.III
III
I-bracket
C3
C4
C1
C2
C1
C2
C3
C44 kinds of...

Suspension bracketI
Suspension bracketIIISuspension bracketII
2. Insert the suspension bracket into bracket cover of
adaptor side and the back of the fan body. (Fig.15)
(select the suspension bracket according to spacing A
as shown below)
A16 inches and 19.2 inches
horizental joist
19.2 inches vertical joist
13
INSTALLATION JOIST MOUNTINGIV( BETWEEN )INSTALLATION JOIST MOUNTINGIV( BETWEEN )
3. Insert the fan body between joists. Make sure the fan
body is level and square (perpendicular) with the joists....

Wire nut Green wires
Lead wiresRed wires
ConduitJunction boxJunction box
Wire nut Lead wires
Conduit
Green wires
14
INSTALLATION WOODEN HEADEV(R)INSTALLATION WOODEN HEADEV(R)
4. Follow steps 4 to 12 of installation (page 9, page 10)
to complete the installation work.I
3. Install the fan body and secure it by using long
screws(ST4.2X20) (Fig.19, Fig.20)
(275)(375)10 7/814 3/4
Joist Header Joist2. Install header between joists by using nails or screws.
inches (mm)Fig.19
Adaptor
Fan body
INSTALLATION IN...

15
MAINTENANCE CLEANINGI()MAINTENANCE CLEANINGI()
Fig.22
4. Remove dust and dirt from fan body using a vacuum
cleaner. (Fig.24)
5. Using a cloth dampened with kitchen detergent, remove
any dirt from fan body. Wipe dry with new cloth. (Fig.25)
6. Replace grille.
Fig.24
Fig.25
Fig.23
3. The grille should be dry after cleaning. (Fig.23)
2. Wash and clean grille. (Use non-abrasive kitchen detergent,
wipe dry with new cloth.) (Fig.22)
MAINTENANCEII(REPLACEMENT OF LAMP)MAINTENANCEII(REPLACEMENT OF LAMP)
1....

Warning Concerning Removal of Covers.
The unit should be serviced by qualified technicians only. No service information is provided for customers.
Your product is designed and manufactured to ensure a minimum of maintenance. However, should your
unit ever require service, a nationwide system of factory service centers and AUTHORIZED INDEPENDENT
SERVICE CENTERS is maintained to support your products warranty.
(In the U.S.A.,call 1-866-292-7292 to Customer call Center.)
P ODUCT SE VICERRP ODUCT SE VICERR...

Map Tools: Selects the shortcuts that appear in the map tools 
menu.
Map Layers: Sets the data that appears on the map page 
(page 6).
myMaps: Sets which installed maps the device uses.
Enabling Maps
You can enable map products installed on your device.
TIP: To purchase additional map products, go to www.garmin.com/us/maps.
1Select Settings > Map & Vehicle > myMaps.
2Select a map.
Navigation Settings
To open the Navigation settings page, from the main menu,  select Settings > Navigation.
Calculation...

2If necessary, select a settings category.
3Select  > Restore.
Appendix
Power Cables
Your device can be powered various ways.
•Vehicle power cable
•USB cable
•AC adapter (optional accessory)
Charging the Device
You can charge the battery in the device using any of these methods.
•Connect the device to the vehicle power cable.
•Connect the device to a computer using the included USB cable.
•Connect the device to an optional power adapter accessory, such as a wall power adapter.
Changing the Fuse in the...

My device is not acquiring satellite signals
•Verify the GPS simulator is turned off (page 13).
•Take your device out of parking garages and away from tall buildings and trees.
•Remain stationary for several minutes.
The device does not charge in my vehicle
•Check the fuse in the vehicle power cable (page 14).
•Verify the vehicle is turned on and is supplying power to the power outlet.
•Verify the interior temperature of the vehicle is between 32° and 113°F (between 0° and 45°C).
•Verify that the fuse is...

Index
Symbols2-D map view 73-D map view 7
Aaccessories 14active lane guidance 5adding stops 5addresses, finding 3
alertsaudio 13proximity points 13safety cameras 13
answering calls 9audio, proximity points 13
automatic volume 2enabling 2avoidancesarea 6customizing 6deleting 6disabling 6road 6road features 6
B
batterycharging 1, 2, 14, 15maximizing 15problems 15
Bluetooth technology 9, 15disabling 13enabling 9
Bluetoothtechnology, settings 13brightness 2
Ccables, power 14calibrating fuel economy 11
calls...